Models predicting the performance of IC component or PCB channel during electromagnetic interference

This dissertation is composed of three papers, which cover the prediction of the characteristics of jitter due to crosstalk and due to simultaneous switching noise, and covers susceptibility of delay locked loop (DLL) to electromagnetic interference. In the first paper, an improved tail-fit de-convolution method is proposed for characterizing the impact of deterministic jitter in the presence of random jitter. A Wiener filter de-convolution method is also presented for extracting the characteristics of crosstalk induced jitter from measurements of total jitter made when the crosstalk sources were and were not present. The proposed techniques are shown to work well both in simulations and in measurements of a high-speed link. In the second paper, methods are developed to predict the statistical distribution of timing jitter due to dynamic currents drawn by an integrated circuit (IC) and the resulting power supply noise on the PCB. Distribution of dynamic currents is found through vectorless methods. Results demonstrate the approach can rapidly determine the average and standard deviation of the power supply noise voltage and the peak jitter within 5~15% error, which is more than sufficient for predicting the performance impact on integrated circuits. In the third paper, a model is developed to predict the susceptibility of a DLL to electromagnetic noise on the power supply. With the proposed analytical noise transfer function, peak to peak jitter and cycle to cycle jitter at the DLL output can be estimated, which can be use to predict when soft failures will occur and to better understand how to fix these failures. Simulation and measurement results demonstrate the accuracy of the DLL delay model. --Abstract, page iv

Characterization and modeling of crosstalk bounded uncorrelated jitter (Buj) for high-speed interconnects

As data rates move towards the Gbps regime, effects that may have been ignored at lower data rates are becoming significant. Such signal integrity issues decrease the timing budget of I/O interconnects exponentially and hence, place a stringent requirement on the total jitter budget. The issues that affect signal integrity also affect jitter as both share many common root causes. Jitter can be divided into different subcomponents each with different root causes and properties. Crosstalk Jitter, or commonly referred in the industry as Bounded Uncorrelated Jitter (BUJ), is a jitter subcomponent that is mostly caused by crosstalk coupling from the adjacent interconnects on printed-circuit boards (PCB). However, the characteristics of BUJ are still ill understood. In addition, a mathematical model of jitter and an algorithm to generate a histogram for BUJ have not been developed to this date. The crosstalk-induced pulse characteristic from an aggressor signal is studied here. Based on the superposition principle, a jitter model to calculate the time difference between the distortion-free and the distorted edge crossings was developed. This model is also extended to calculate the worst-case timing difference. In addition, algorithms to generate the histogram distributions of BUJ are also developed. Simulation and measurement results validate the BUJ model. Algorithms developed to generate the histogram for BUJ show reasonable accuracy with four aggressor traces or less. These algorithms have fast execution times of 5~20 seconds, compared to simulation and measurement times in the range of 10~30 minutes, which require data post-processing.Applied Science, Faculty ofElectrical and Computer Engineering, Department ofGraduat

Reducing jitter utilising adaptive pre-emphasis FIR filter for high speed serial links

Jitter requirements have become more stringent with higher speed serial communication links. Reducing jitter, with the main focus on reducing data dependant jitter (DDJ), is presented by employing adaptive finite impulse response (FIR) filter pre-emphasis. The adaptive FIR pre-emphasis is implemented in the IBM 7WL 0.18 µm SiGe BiCMOS process. SiGe heterojunction bipolar transistors (HBTs) provide high bandwidth, low noise devices which could reduce the total system jitter. The trade-offs between utilising metal oxide semiconductor (MOS) current mode logic (CML) and SiGe bipolar CML are also discussed in comparison with a very high fT (IBM 8HP process with fT = 200 GHz) process. A reduction in total system jitter can be achieved by keeping the sub-components of the system jitter constant while optimising the DDJ. High speed CML circuits have been employed to allow data rates in excess of 5 Gb/s to be transmitted whilst still maintaining an internal voltage swing of at least 300 mV. This allows the final FIR filter adaptation scheme to minimise the DDJ within 12.5 % of a unit interval, at a data rate of 5 Gb/s implementing 6 FIR pre-emphasis filter taps, for a worst case copper backplane channel (30" FR-4 channel). The implemented integrated circuit (IC) designed as part of the verification process takes up less than 1 mm2 of silicon real estate. In this dissertation, SPICE simulation results are presented, as well as the novel IC implementation of the proposed FIR filter adaptation technique as part of the hypothesis verification procedure. The implemented transmitter and receiver were tested for functionality, and showed the successful functional behaviour of all the implemented CML gates associated with the first filter tap. However, due to the slow charge and discharge rate of the pulse generation circuit in both the transmitter and receiver, only the main operational state of the transmitter could be experimentally validated. As a result of the adaptation scheme implemented, the contribution in this research lies in that a designer utilising such an IC can optimise the DDJ, reducing the total system jitter, and hence increasing the data fidelity with minimal effort.Dissertation (MEng)--University of Pretoria, 2011.Electrical, Electronic and Computer Engineeringunrestricte