Smart Sensor Networks For Sensor-Neural Interface

One in every fifty Americans suffers from paralysis, and approximately 23% of paralysis cases are caused by spinal cord injury. To help the spinal cord injured gain functionality of their paralyzed or lost body parts, a sensor-neural-actuator system is commonly used. The system includes: 1) sensor nodes, 2) a central control unit, 3) the neural-computer interface and 4) actuators. This thesis focuses on a sensor-neural interface and presents the research related to circuits for the sensor-neural interface. In Chapter 2, three sensor designs are discussed, including a compressive sampling image sensor, an optical force sensor and a passive scattering force sensor. Chapter 3 discusses the design of the analog front-end circuit for the wireless sensor network system. A low-noise low-power analog front-end circuit in 0.5μm CMOS technology, a 12-bit 1MS/s successive approximation register (SAR) analog-to-digital converter (ADC) in 0.18μm CMOS process and a 6-bit asynchronous level-crossing ADC realized in 0.18μm CMOS process are presented. Chapter 4 shows the design of a low-power impulse-radio ultra-wide-band (IR-UWB) transceiver (TRx) that operates at a data rate of up to 10Mbps, with a power consumption of 4.9pJ/bit transmitted for the transmitter and 1.12nJ/bit received for the receiver. In Chapter 5, a wireless fully event-driven electrogoniometer is presented. The electrogoniometer is implemented using a pair of ultra-wide band (UWB) wireless smart sensor nodes interfacing with low power 3-axis accelerometers. The two smart sensor nodes are configured into a master node and a slave node, respectively. An experimental scenario data analysis shows higher than 90% reduction of the total data throughput using the proposed fully event-driven electrogoniometer to measure joint angle movements when compared with a synchronous Nyquist-rate sampling system. The main contribution of this thesis includes: 1) the sensor designs that emphasize power efficiency and data throughput efficiency; 2) the fully event-driven wireless sensor network system design that minimizes data throughput and optimizes power consumption

Systems and Methods for the Spectral Calibration of Swept Source Optical Coherence Tomography Systems

This dissertation relates to the transition of the state of the art of swept source optical coherence tomography (SS-OCT) systems to a new realm in which the image acquisition speed is improved by an order of magnitude. With the aid of a better quality imaging technology, the speed-up factor will considerably shorten the eye-exam clinical visits which in turn improves the patient and doctor interaction experience. These improvements will directly lower associated medical costs for eye-clinics and patients worldwide. There are several other embodiments closely related to Optical Coherence Tomography (OCT) that could benefit from the ideas presented in this dissertation including: optical coherence microscopy (OCM), full-field OCT (FF-OCT), optical coherence elastography (OCE), optical coherence tomography angiography (OCT-A), anatomical OCT (aOCT), optical coherence photoacoustic microscopy (OC-PAM), micro optical coherence tomography (µ OCT), among others. In recent decades, OCT has established itself as the de-facto imaging process that most ophthalmologists refer to in their clinical practices. In a broader sense, optical coherence tomography is used in applications when low penetration and high resolution are desired. These applications include different fields of biomedical sciences including cardiology, dermatology, and pulmonary related sciences. Many other industrial applications including quality control and precise measurements have also been reported that are related to the OCT technology. Every new iteration of OCT technology has always come about with advanced signal processing and data acquisition algorithms using mixed-signal architectures, calibration and signal processing techniques. The existing industrial practices towards data acquisition, processing, and image creation relies on conventional signal processing design flows, which extensively employ continuous/discrete techniques that are both time-consuming and costly. The ideas presented in this dissertation can take the technology to a new dimension of quality of service

Continuous-Time and Companding Digital Signal Processors Using Adaptivity and Asynchronous Techniques

The fully synchronous approach has been the norm for digital signal processors (DSPs) for many decades. Due to its simplicity, the classical DSP structure has been used in many applications. However, due to its rigid discrete-time operation, a classical DSP has limited efficiency or inadequate resolution for some emerging applications, such as processing of multimedia and biological signals. This thesis proposes fundamentally new approaches to designing DSPs, which are different from the classical scheme. The defining characteristic of all new DSPs examined in this thesis is the notion of "adaptivity" or "adaptability." Adaptive DSPs dynamically change their behavior to adjust to some property of their input stream, for example the rate of change of the input. This thesis presents both enhancements to existing adaptive DSPs, as well as new adaptive DSPs. The main class of DSPs that are examined throughout the thesis are continuous-time (CT) DSPs. CT DSPs are clock-less and event-driven; they naturally adapt their activity and power consumption to the rate of their inputs. The absence of a clock also provides a complete avoidance of aliasing in the frequency domain, hence improved signal fidelity. The core of this thesis deals with the complete and systematic design of a truly general-purpose CT DSP. A scalable design methodology for CT DSPs is presented. This leads to the main contribution of this thesis, namely a new CT DSP chip. This chip is the first general-purpose CT DSP chip, able to process many different classes of CT and synchronous signals. The chip has the property of handling various types of signals, i.e. various different digital modulations, both synchronous and asynchronous, without requiring any reconfiguration; such property is presented for the first time CT DSPs and is impossible for classical DSPs. As opposed to previous CT DSPs, which were limited to using only one type of digital format, and whose design was hard to scale for different bandwidths and bit-widths, this chip has a formal, robust and scalable design, due to the systematic usage of asynchronous design techniques. The second contribution of this thesis is a complete methodology to design adaptive delay lines. In particular, it is shown how to make the granularity, i.e. the number of stages, adaptive in a real-time delay line. Adaptive granularity brings about a significant improvement in the line's power consumption, up to 70% as reported by simulations on two design examples. This enhancement can have a direct large power impact on any CT DSP, since a delay line consumes the majority of a CT DSP's power. The robust methodology presented in this thesis allows safe dynamic reconfiguration of the line's granularity, on-the-fly and according to the input traffic. As a final contribution, the thesis also examines two additional DSPs: one operating the CT domain and one using the companding technique. The former operates only on level-crossing samples; the proposed methodology shows a potential for high-quality outputs by using a complex interpolation function. Finally, a companding DSP is presented for MPEG audio. Companding DSPs adapt their dynamic range to the amplitude of their input; the resulting can offer high-quality outputs even for small inputs. By applying companding to MPEG DSPs, it is shown how the DSP distortion can be made almost inaudible, without requiring complex arithmetic hardware