Multi-Frequency Modulation and Control for DC/AC and AC/DC Resonant Converters

Harmonic content is inherent in switched-mode power supplies. Since the undesired harmonics interfere with the operation of other sensitive electronics, the reduction of harmonic content is essential for power electronics design. Conventional approaches to attenuate the harmonic content include passive/active filter and wave-shaping in modulation. However, those approaches are not suitable for resonant converters due to bulky passive volumes and excessive switching losses. This dissertation focuses on eliminating the undesired harmonics from generation by intelligently manipulating the spectrum of switching waveforms, considering practical needs for functionality.To generate multiple ac outputs while eliminating the low-order harmonics from a single inverter, a multi-frequency programmed pulse width modulation is investigated. The proposed modulation schemes enable multi-frequency generation and independent output regulation. In this method, the fundamental and certain harmonics are independently controlled for each of the outputs, allowing individual power regulations. Also, undesired harmonics in between output frequencies are easily eliminated from generation, which prevents potential hazards caused by the harmonic content and bulky filters. Finally, the proposed modulation schemes are applicable to a variety of DC/AC topologies.Two applications of dc/ac resonant inverters, i.e. an electrosurgical generator and a dual-mode WPT transmitter, are demonstrated using the proposed MFPWM schemes. From the experimental results of two hardware prototypes, the MFPWM alleviates the challenges of designing a complicated passive filter for the low-order harmonics. In addition, the MFPWM facilitates combines functionalities using less hardware compared to the state-of-the-art. The prototypes demonstrate a comparable efficiency while achieving multiple ac outputs using a single inverter.To overcome the low-efficiency, low power-density problems in conventional wireless fast charging, a multi-level switched-capacitor ac/dc rectifier is investigated. This new WPT receiver takes advantage of a high power-density switched-capacitor circuit, the low harmonic content of the multilevel MFPWMs, and output regulation ability to improve the system efficiency. A detailed topology evaluation regarding the regulation scheme, system efficiency, current THD and volume estimation is demonstrated, and experimental results from a 20 W prototype prove that the multi-level switched-capacitor rectifier is an excellent candidate for high-efficiency, high power density design of wireless fast charging receiver

Frequency splitting elimination and cross-coupling rejection of wireless power transfer to multiple dynamic receivers

Simultaneous power transfer to multiple receiver (Rx) system is one of the key advantages of wireless power transfer (WPT) system using magnetic resonance. However, determining the optimal condition to uniformly transfer the power to a selected Rx at high efficiency is the challenging task under the dynamic environment. The cross-coupling and frequency splitting are the dominant issues present in the multiple Rx dynamic WPT system. The existing analysis is performed by considering any one issue present in the system; on the other hand, the cross coupling and frequency splitting issues are interrelated in dynamic Rx’s, which requires a comprehensive design strategy by considering both the problems. This paper proposes an optimal design of multiple Rx WPT system, which can eliminate cross coupling, frequency splitting issues and increase the power transfer efficiency (PTE) of selected Rx. The cross-coupling rejection, uniform power transfer is performed by adding an additional relay coil and independent resonance frequency tuning with capacitive compensation to each Rx unit. The frequency splitting phenomena are eliminated using non-identical transmitter (Tx) and Rx coil structure which can maintain the coupling between the coil under the critical coupling limit. The mathematical analysis of the compensation capacitance calculation and optimal Tx coil size identification is performed for the four Rx WPT system. Finite element analysis and experimental investigation are carried out for the proposed design in static and dynamic conditions

FDMA Enabled Phase-based Wireless Network-on-Chip using Graphene-based THz-band Antennas

The future growth in System-on-chip design is moving in the direction of multicore systems. Design of efficient interconnects between cores are crucial for improving the performance of a multicore processor. Such trends are seen due to the benefits the multicore systems provide in terms of power reduction and scalability. Network-on-chips (NoC) are viewed as an emerging solution in the design of interconnects in multicore systems. However, Traditional Network-on-chip architectures are no longer able to satisfy the performance requirements due to long distance communication over multi-hop wireline paths. Multi-hop communication leads to higher energy consumption, increase in latency and reduction in bandwidth. Research in recent years has explored emerging technologies such as 3D integration, photonic and radio frequency based Network-on-chips. The use of wireless interconnects using mm-wave antennas are able to alleviate the performance issues in a wireline interconnect system. However, to satisfy the increasing demand for higher bandwidth and lower energy consumption, Wireless Network-on-Chip enabled with high speed direct links operating in THz band between distant cores is desired. Recent research has brought to light highly efficient graphene-based antennas operating in THz band. These antennas can provide high data rate and are found to consume less power with low area overheads. In this thesis, an innovative approach using novel devices based on graphene structures is proposed to provide a high-performance on-chip interconnection. This novel approach combines the regular NoC structure with the proposed wireless infrastructure to exploit the performance benefits. An architecture with wireless interfaces on every core is explored in this work. Simultaneous multiple communications in a network can be achieved by adopting Frequency Division Multiple access (FDMA). However, in a system where all cores are equipped with a wireless interface, FDMA requires more number of frequency bands. This becomes difficult to achieve as the system scales and the number of cores increase. Therefore, a FDMA protocol along with a 4-phased repetitive multi-band architecture is envisioned in this work. The phase-based protocol allows multiple wireless links to be active at a time, the phase-based protocol along with the FDMA protocol provides a reliable data transfer between cores with lesser number of frequency bands. In this thesis, an architecture with a combination of FDMA and phase-based protocol using point-to-point graphene-based wireless links is proposed. The proposed architecture is also extended for a multichip system. With cycle accurate system-level simulations, it is shown that the proposed architecture provides huge gains in performance and energy-efficiency in data transfer both in NoC based multicore and multichip systems

A Scalable & Energy Efficient Graphene-Based Interconnection Framework for Intra and Inter-Chip Wireless Communication in Terahertz Band

Network-on-Chips (NoCs) have emerged as a communication infrastructure for the multi-core System-on-Chips (SoCs). Despite its advantages, due to the multi-hop communication over the metal interconnects, traditional Mesh based NoC architectures are not scalable in terms of performance and energy consumption. Folded architectures such as Torus and Folded Torus were proposed to improve the performance of NoCs while retaining the regular tile-based structure for ease of manufacturing. Ultra-low-latency and low-power express channels between communicating cores have also been proposed to improve the performance of conventional NoCs. However, the performance gain of these approaches is limited due to metal/dielectric based interconnection. Many emerging interconnect technologies such as 3D integration, photonic, Radio Frequency (RF), and wireless interconnects have been envisioned to alleviate the issues of a metal/dielectric interconnect system. However, photonic and RF interconnects need the additional physically overlaid optical waveguides or micro-strip transmission lines to enable data transmission across the NoC. Several on-chip antennas have shown to improve energy efficiency and bandwidth of on-chip data communications. However, the date rates of the mm-wave wireless channels are limited by the state-of-the-art power-efficient transceiver design. Recent research has brought to light novel graphene based antennas operating at THz frequencies. Due to the higher operating frequencies compared to mm-wave transceivers, the data rate that can be supported by these antennas are significantly higher. Higher operating frequencies imply that graphene based antennas are just hundred micrometers in size compared to dimensions in the range of a millimeter of mm-wave antennas. Such reduced dimensions are suitable for integration of several such transceivers in a single NoC for relatively low overheads. In this work, to exploit the benefits of a regular NoC structure in conjunction with emerging Graphene-based wireless interconnect. We propose a toroidal folding based NoC architecture. The novelty of this folding based approach is that we are using low power, high bandwidth, single hop direct point to point wireless links instead of multihop communication that happens through metallic wires. We also propose a novel phased based communication protocol through which multiple wireless links can be made active at a time without having any interference among the transceiver. This offers huge gain in terms of performance as compared to token based mechanism where only a single wireless link can be made active at a time. We also propose to extend Graphene-based wireless links to enable energy-efficient, phase-based chip-to-chip communication to create a seamless, wireless interconnection fabric for multichip systems as well. Through cycle-accurate system-level simulations, we demonstrate that such designs with torus like folding based on THz links instead of global wires along with the proposed phase based multichip systems. We provide estimates that they are able to provide significant gains (about 3 to 4 times better in terms of achievable bandwidth, packet latency and average packet energy when compared to wired system) in performance and energy efficiency in data transfer in a NoC as well as multichip system. Thus, realization of these kind of interconnection framework that could support high data rate links in Tera-bits-per-second that will alleviate the capacity limitations of current interconnection framework

A Multiband Low Noise Amplifier for Software Defined Radio Using Switchable Active Shunt Feedback Input Matching

Radio frequency (RF) receivers are the key front-end blocks in wireless devices such as smartphones, pagers, PDAs etc. An important block of the RF receiver is the Low-noise amplifier. It’s function is to amplify with little noise addition, the RF signal received at the atenna. Modern wireless devices for example the smartphone, incorporates multiple functionalities supported by various RF standards- GPS, Bluetooth, Wifi, GSM etc. Thus, the current trend in the wireless technology is to integrate radio receivers for each RF standard into a single system-on-chip (SoC) in order to reduce cost and area of the devices. In view of this, multiband RF receivers have been developed which feature multiband LNAs. This thesis presents the design and implementation of a multiband LNA for Software Defined Radio Applications. In this thesis, basic radio-frequency concepts are discussed which is followed by a discussion of pros and cons of various multistandard low-noise amplifier topologies. This is then followed by the design of the proposed reconfigurable LNA. The LNA is designed and fabricated in IBM 0.18um CMOS technology. It is made up of dual LC resonant tanks, one to switch between 5.2GHz and 3.5GHz frequency bands and the other, to switch between 2.4GHz and 1.8GHz bands. The input matching of the LNA is achieved using a switchable shunt active feedback network. The LNA achieves S21 of between 10.1dB and 13.43dB. It achieves an input matching (S11) between -13.44 dB and -11.97 dB. The noise figure measured ranges from 2.8 dB to 4.3 dB. The LNA also achieves an IIP3 from -7.12 dBm to -3.45 dBm at 50 MHz offset. The power consumption ranges from 7 mW to 7.2 mW

System and Circuit Design Techniques for Silicon-based Multi-band/Multi-standard Receivers

Today, the advances in Complementary MetalOxideSemiconductor (CMOS) technology have guided the progress in the wireless communications circuits and systems area. Various new communication standards have been developed to accommodate a variety of applications at different frequency bands, such as cellular communications at 900 and 1800 MHz, global positioning system (GPS) at 1.2 and 1.5 GHz, and Bluetooth andWiFi at 2.4 and 5.2 GHz, respectively. The modern wireless technology is now motivated by the global trend of developing multi-band/multistandard terminals for low-cost and multifunction transceivers. Exploring the unused 10-66 GHz frequency spectrum for high data rate communication is also another trend in the wireless industry. In this dissertation, the challenges and solutions for designing a multi-band/multistandard mobile device is addressed from system-level analysis to circuit implementation. A systematic system-level design methodology for block-level budgeting is proposed. The system-level design methodology focuses on minimizing the power consumption of the overall receiver. Then, a novel millimeter-wave dual-band receiver front-end architecture is developed to operate at 24 and 31 GHz. The receiver relies on a newly introduced concept of harmonic selection that helps to reduce the complexity of the dual-band receiver. Wideband circuit techniques for millimeterwave frequencies are also investigated and new bandwidth extension techniques are proposed for the dual-band 24/31 GHz receiver. These new techniques are applied for the low noise amplifier and millimeter-wave mixer resulting in the widest reported operating bandwidth in K-band, while consuming less power consumption. Additionally, various receiver building blocks, such as a low noise amplifier with reconfigurable input matching network for multi-band receivers, and a low drop-out regulator with high power supply rejection are analyzed and proposed. The low noise amplifier presents the first one with continuously reconfigurable input matching network, while achieving a noise figure comparable to the wideband techniques. The low drop-out regulator presented the first one with high power supply rejection in the mega-hertz frequency range. All the proposed building blocks and architecture in this dissertation are implemented using the existing silicon-based technologies, and resulted in several publications in IEEE Journals and Conferences

Reconfigurable Receiver Front-Ends for Advanced Telecommunication Technologies

The exponential growth of converging technologies, including augmented reality, autonomous vehicles, machine-to-machine and machine-to-human interactions, biomedical and environmental sensory systems, and artificial intelligence, is driving the need for robust infrastructural systems capable of handling vast data volumes between end users and service providers. This demand has prompted a significant evolution in wireless communication, with 5G and subsequent generations requiring exponentially improved spectral and energy efficiency compared to their predecessors. Achieving this entails intricate strategies such as advanced digital modulations, broader channel bandwidths, complex spectrum sharing, and carrier aggregation scenarios. A particularly challenging aspect arises in the form of non-contiguous aggregation of up to six carrier components across the frequency range 1 (FR1). This necessitates receiver front-ends to effectively reject out-of-band (OOB) interferences while maintaining high-performance in-band (IB) operation. Reconfigurability becomes pivotal in such dynamic environments, where frequency resource allocation, signal strength, and interference levels continuously change. Software-defined radios (SDRs) and cognitive radios (CRs) emerge as solutions, with direct RF-sampling receivers offering a suitable architecture in which the frequency translation is entirely performed in digital domain to avoid analog mixing issues. Moreover, direct RF- sampling receivers facilitate spectrum observation, which is crucial to identify free zones, and detect interferences. Acoustic and distributed filters offer impressive dynamic range and sharp roll off characteristics, but their bulkiness and lack of electronic adjustment capabilities limit their practicality. Active filters, on the other hand, present opportunities for integration in advanced CMOS technology, addressing size constraints and providing versatile programmability. However, concerns about power consumption, noise generation, and linearity in active filters require careful consideration.This thesis primarily focuses on the design and implementation of a low-voltage, low-power RFFE tailored for direct sampling receivers in 5G FR1 applications. The RFFE consists of a balun low-noise amplifier (LNA), a Q-enhanced filter, and a programmable gain amplifier (PGA). The balun-LNA employs noise cancellation, current reuse, and gm boosting for wideband gain and input impedance matching. Leveraging FD-SOI technology allows for programmable gain and linearity via body biasing. The LNA's operational state ranges between high-performance and high-tolerance modes, which are apt for sensitivityand blocking tests, respectively. The Q-enhanced filter adopts noise-cancelling, current-reuse, and programmable Gm-cells to realize a fourth-order response using two resonators. The fourth-order filter response is achieved by subtracting the individual response of these resonators. Compared to cascaded and magnetically coupled fourth-order filters, this technique maintains the large dynamic range of second-order resonators. Fabricated in 22-nm FD-SOI technology, the RFFE achieves 1%-40% fractional bandwidth (FBW) adjustability from 1.7 GHz to 6.4 GHz, 4.6 dB noise figure (NF) and an OOB third-order intermodulation intercept point (IIP3) of 22 dBm. Furthermore, concerning the implementation uncertainties and potential variations of temperature and supply voltage, design margins have been considered and a hybrid calibration scheme is introduced. A combination of on-chip and off-chip calibration based on noise response is employed to effectively adjust the quality factors, Gm-cells, and resonance frequencies, ensuring desired bandpass response. To optimize and accelerate the calibration process, a reinforcement learning (RL) agent is used.Anticipating future trends, the concept of the Q-enhanced filter extends to a multiple-mode filter for 6G upper mid-band applications. Covering the frequency range from 8 to 20 GHz, this RFFE can be configured as a fourth-order dual-band filter, two bandpass filters (BPFs) with an OOB notch, or a BPF with an IB notch. In cognitive radios, the filter’s transmission zeros can be positioned with respect to the carrier frequencies of interfering signals to yield over 50 dB blocker rejection

RF Power Transfer, Energy Harvesting, and Power Management Strategies

Energy harvesting is the way to capture green energy. This can be thought of as a recycling process where energy is converted from one form (here, non-electrical) to another (here, electrical). This is done on the large energy scale as well as low energy scale. The former can enable sustainable operation of facilities, while the latter can have a significant impact on the problems of energy constrained portable applications. Different energy sources can be complementary to one another and combining multiple-source is of great importance. In particular, RF energy harvesting is a natural choice for the portable applications. There are many advantages, such as cordless operation and light-weight. Moreover, the needed infra-structure can possibly be incorporated with wearable and portable devices. RF energy harvesting is an enabling key player for Internet of Things technology. The RF energy harvesting systems consist of external antennas, LC matching networks, RF rectifiers for ac to dc conversion, and sometimes power management. Moreover, combining different energy harvesting sources is essential for robustness and sustainability. Wireless power transfer has recently been applied for battery charging of portable devices. This charging process impacts the daily experience of every human who uses electronic applications. Instead of having many types of cumbersome cords and many different standards while the users are responsible to connect periodically to ac outlets, the new approach is to have the transmitters ready in the near region and can transfer power wirelessly to the devices whenever needed. Wireless power transfer consists of a dc to ac conversion transmitter, coupled inductors between transmitter and receiver, and an ac to dc conversion receiver. Alternative far field operation is still tested for health issues. So, the focus in this study is on near field. The goals of this study are to investigate the possibilities of RF energy harvesting from various sources in the far field, dc energy combining, wireless power transfer in the near field, the underlying power management strategies, and the integration on silicon. This integration is the ultimate goal for cheap solutions to enable the technology for broader use. All systems were designed, implemented and tested to demonstrate proof-of concept prototypes

Millimeter-Wave Concurrent Dual-Band BiCMOS RFICs for Radar and Communication RF Front-End

The recent advancement in silicon-based technologies has offered the opportunity for the development of highly-integrated circuits and systems in the millimeter-wave frequency regime. In particular, the demand for high performance multi-band multi-mode radar and communication systems built on silicon-based technologies has been increased dramatically for both military and commercial applications. This dissertation presents the design and implementation of advanced millimeter-wave front-end circuits in SiGe BiCMOS process including a transmit/receive switch module with integrated calibration function, low noise amplifier, and power amplifier for millimeter-wave concurrent dual-band dual-polarization radars and communication systems. The proposed circuits designed for the concurrent dual-band dual-polarization radars and communication systems were fabricated using 0.18-μm BiCMOS process resulting in novel circuit architectures for concurrent multi-band operation. The developed concurrent dual-band circuits fabricated on 0.18-μm BiCMOS process include the T/R/Calibration switch module for digital beam forming array system at 24.5/35 GHz, concurrent dual-band low noise amplifiers at 44/60 GHz, and concurrent dual-band power amplifier at 44/60 GHz. With having all the design frequencies closely spaced to each other showing the frequency ratio below 1.43, the designed circuits provided the integrated dual-band filtering function with Q-enhanced frequency responses. Inspired by the composite right/left- handed metamaterial transmission line approaches, the integrated Q-enhanced filtering sub-circuits provided unprecedented dual-band filtering capability. The new concurrent dual-band dual-mode circuits and system architecture can provide enhanced radar and communication system performance with extended coverage, better image synthesis and target locating by the enhanced diversity. The circuit level hardware research conducted in this dissertation is expected to contribute to enhance the performance of multi-band multi-mode imaging, sensing, and communication array systems