An FPGA Architecture and CAD Flow Supporting Dynamically Controlled Power Gating

© 2015 IEEE.Leakage power is an important component of the total power consumption in field-programmable gate arrays (FPGAs) built using 90-nm and smaller technology nodes. Power gating was shown to be effective at reducing the leakage power. Previous techniques focus on turning OFF unused FPGA resources at configuration time; the benefit of this approach depends on resource utilization. In this paper, we present an FPGA architecture that enables dynamically controlled power gating, in which FPGA resources can be selectively powered down at run-time. This could lead to significant overall energy savings for applications having modules with long idle times. We also present a CAD flow that can be used to map applications to the proposed architecture. We study the area and power tradeoffs by varying the different FPGA architecture parameters and power gating granularity. The proposed CAD flow is used to map a set of benchmark circuits that have multiple power-gated modules to the proposed architecture. Power savings of up to 83% are achievable for these circuits. Finally, we study a control system of a robot that is used in endoscopy. Using the proposed architecture combined with clock gating results in up to 19% energy savings in this application

Timing verification of dynamically reconfigurable logic for Xilinx Virtex FPGA series

This paper reports on a method for extending existing VHDL design and verification software available for the Xilinx Virtex series of FPGAs. It allows the designer to apply standard hardware design and verification tools to the design of dynamically reconfigurable logic (DRL). The technique involves the conversion of a dynamic design into multiple static designs, suitable for input to standard synthesis and APR tools. For timing and functional verification after APR, the sections of the design can then be recombined into a single dynamic system. The technique has been automated by extending an existing DRL design tool named DCSTech, which is part of the Dynamic Circuit Switching (DCS) CAD framework. The principles behind the tools are generic and should be readily extensible to other architectures and CAD toolsets. Implementation of the dynamic system involves the production of partial configuration bitstreams to load sections of circuitry. The process of creating such bitstreams, the final stage of our design flow, is summarized

Towards a Holistic CAD Platform for Nanotechnologies

Silicon-based CMOS technologies are predicted to reach their ultimate limits by the middle of the next decade. Research on nanotechnologies is actively conducted, in a world-wide effort to develop new technologies able to maintain the Moore's law. They promise revolutionizing the computing systems by integrating tremendous numbers of devices at low cost. These trends will have a profound impact on the architectures of computing systems and will require a new paradigm of CAD. The paper presents a work in progress on this direction. It is aimed at fitting requirements and constraints of nanotechnologies, in an effort to achieve efficient use of the huge computing power promised by them. To achieve this goal we are developing CAD tools able to exploit efficiently these huge computing capabilities promised by nanotechnologies in the domain of simulation of complex systems composed by huge numbers of relatively simple elements.Comment: Submitted on behalf of TIMA Editions (http://irevues.inist.fr/tima-editions

CRoute: a fast high-quality timing-driven connection-based FPGA router

FPGA routing is an important part of physical design as the programmable interconnection network requires the majority of the total silicon area and the connections largely contribute to delay and power. It should also occur with minimum runtime to enable efficient design exploration. In this work we elaborate on the concept of the connection-based routing principle. The algorithm is improved and a timing-driven version is introduced. The router, called CROUTE, is implemented in an easy to adapt FPGA CAD framework written in Java, which is publicly available on GitHub. Quality and runtime are compared to the state-of-the-art router in VPR 7.0.7. Benchmarking is done with the TITAN23 design suite, which consists of large heterogeneous designs targeted to a detailed representation of the Stratix IV FPGA. CROUTE gains in both the total wirelength and maximum clock frequency while reducing the routing runtime. The total wire-length reduces by 11% and the maximum clock frequency increases by 6%. These high-quality results are obtained in 3.4x less routing runtime

Pixie: A heterogeneous Virtual Coarse-Grained Reconfigurable Array for high performance image processing applications

Coarse-Grained Reconfigurable Arrays (CGRAs) enable ease of programmability and result in low development costs. They enable the ease of use specifically in reconfigurable computing applications. The smaller cost of compilation and reduced reconfiguration overhead enables them to become attractive platforms for accelerating high-performance computing applications such as image processing. The CGRAs are ASICs and therefore, expensive to produce. However, Field Programmable Gate Arrays (FPGAs) are relatively cheaper for low volume products but they are not so easily programmable. We combine best of both worlds by implementing a Virtual Coarse-Grained Reconfigurable Array (VCGRA) on FPGA. VCGRAs are a trade off between FPGA with large routing overheads and ASICs. In this perspective we present a novel heterogeneous Virtual Coarse-Grained Reconfigurable Array (VCGRA) called "Pixie" which is suitable for implementing high performance image processing applications. The proposed VCGRA contains generic processing elements and virtual channels that are described using the Hardware Description Language VHDL. Both elements have been optimized by using the parameterized configuration tool flow and result in a resource reduction of 24% for each processing elements and 82% for each virtual channels respectively.Comment: Presented at 3rd International Workshop on Overlay Architectures for FPGAs (OLAF 2017) arXiv:1704.0880

A fully parameterized virtual coarse grained reconfigurable array for high performance computing applications

Field Programmable Gate Arrays (FPGAs) have proven their potential in accelerating High Performance Computing (HPC) Applications. Conventionally such accelerators predominantly use, FPGAs that contain fine-grained elements such as LookUp Tables (LUTs), Switch Blocks (SB) and Connection Blocks (CB) as basic programmable logic blocks. However, the conventional implementation suffers from high reconfiguration and development costs. In order to solve this problem, programmable logic components are defined at a virtual higher abstraction level. These components are called Processing Elements (PEs) and the group of PEs along with the inter-connection network form an architecture called a Virtual Coarse-Grained Reconfigurable Array (VCGRA). The abstraction helps to reconfigure the PEs faster at the intermediate level than at the lower-level of an FPGA. Conventional VCGRA implementations (built on top of the lower levels of the FPGA) use functional resources such as LUTs to establish required connections (intra-connect) within a PE. In this paper, we propose to use the parameterized reconfiguration technique to implement the intra-connections of each PE with the aim to reduce the FPGA resource utilization (LUTs). The technique is used to parameterize the intra-connections with parameters that only change their value infrequently (whenever a new VCGRA function has to be reconfigured) and that are implemented as constants. Since the design is optimized for these constants at every moment in time, this reduces the resource utilization. Further, interconnections (network between the multiple PEs) of the VCGRA grid can also be parameterized so that both the inter- and intraconnect network of the VCGRA grid can be mapped onto the physical switch blocks of the FPGA. For every change in parameter values a specialized bitstream is generated on the fly and the FPGA is reconfigured using the parameterized run-time reconfiguration technique. Our results show a drastic reduction in FPGA LUT resource utilization in the PE by at least 30% and in the intra-network of the PE by 31% when implementing an HPC application