Effect of dimples on glancing shock wave turbulent boundary layer interactions

An experimental study has been conducted to examine the control effectiveness of dimples on the glancing shock wave turbulent boundary layer interaction produced by a series of hemi-cylindrically blunted fins at Mach numbers 0.8 and 1.4, and at angles of sweep 0°, 15°, 30° and 45°. Schlieren photography, oil flow, pressure sensitive paints, and pressure tappings were employed to examine the characteristics of the induced flow field. The passive control technique used a series of 2 mm diameter, 1 mm deep indents drilled across the hemi-cylindrical leading edge at angles 0°, 45° and 90°. The effects of dimples were highly dependent on their orientation relative to the leading edge apex, and the local boundary layer properties

Compendium of NASA Langley reports on hypersonic aerodynamics

Reference is made to papers published by the Langley Research Center in various areas of hypersonic aerodynamics for the period 1950 to 1986. The research work was performed either in-house by the Center staff or by other personnel supported entirely or in part by grants or contracts. Abstracts have been included with the references when available. The references are listed chronologically and are grouped under the following general headings: (1) Aerodynamic Measurements - Single Shapes; (2) Aerodynamic Measurements - Configurations; (3) Aero-Heating; (4) Configuration Studies; (5) Propulsion Integration Experiment; (6) Propulsion Integration - Study; (7) Analysis Methods; (8) Test Techniques; and (9) Airframe Active Cooling Systems

A survey of computational aerodynamics in the United States

Programs in theoretical and computational aerodynamics in the United States are described. Those aspects of programs that relate to aeronautics are detailed. The role of analysis at various levels of sophistication is discussed as well as the inverse solution techniques that are of primary importance in design methodology. The research is divided into the broad categories of application for boundary layer flow, Navier-Stokes turbulence modeling, internal flows, two-dimensional configurations, subsonic and supersonic aircraft, transonic aircraft, and the space shuttle. A survey of representative work in each area is presented

Reynolds number influences in aeronautics

Reynolds number, a measure of the ratio of inertia to viscous forces, is a fundamental similarity parameter for fluid flows and therefore, would be expected to have a major influence in aerodynamics and aeronautics. Reynolds number influences are generally large, but monatomic, for attached laminar (continuum) flow; however, laminar flows are easily separated, inducing even stronger, non-monatomic, Reynolds number sensitivities. Probably the strongest Reynolds number influences occur in connection with transitional flow behavior. Transition can take place over a tremendous Reynolds number range, from the order of 20 x 10(exp 3) for 2-D free shear layers up to the order of 100 x 10(exp 6) for hypersonic boundary layers. This variability in transition behavior is especially important for complex configurations where various vehicle and flow field elements can undergo transition at various Reynolds numbers, causing often surprising changes in aerodynamics characteristics over wide ranges in Reynolds number. This is further compounded by the vast parameterization associated with transition, in that any parameter which influences mean viscous flow development (e.g., pressure gradient, flow curvature, wall temperature, Mach number, sweep, roughness, flow chemistry, shock interactions, etc.), and incident disturbance fields (acoustics, vorticity, particulates, temperature spottiness, even electro static discharges) can alter transition locations to first order. The usual method of dealing with the transition problem is to trip the flow in the generally lower Reynolds number wind tunnel to simulate the flight turbulent behavior. However, this is not wholly satisfactory as it results in incorrectly scaled viscous region thicknesses and cannot be utilized at all for applications such as turbine blades and helicopter rotors, nacelles, leading edge and nose regions, and High Altitude Long Endurance and hypersonic airbreathers where the transitional flow is an innately critical portion of the problem

Supersonic laminar-flow control

Detailed, up to date systems studies of the application of laminar flow control (LFC) to various supersonic missions and/or vehicles, both civilian and military, are not yet available. However, various first order looks at the benefits are summarized. The bottom line is that laminar flow control may allow development of a viable second generation SST. This follows from a combination of reduced fuel, structure, and insulation weight permitting operation at higher altitudes, thereby lowering sonic boom along with improving performance. The long stage lengths associated with the emerging economic importance of the Pacific Basin are creating a serious and renewed requirement for such a vehicle. Supersonic LFC techniques are discussed

Analytical and experimental studies of shock interference heating in hypersonic flows

An analytical and experimental study is presented of the aerodynamic heating resulting from six types of shock interference patterns encountered in high speed flow. Centerline measurements of pressure and heat transfer distributions on basic bodies were obtained in four wind tunnels for Mach numbers from 6 to 20, specific heat ratios from 1.27 to 1.67, and free stream Reynolds numbers from 3 million to 25.6 million per meter. Peak heating and peak pressures up to 17 and 7.5 times stagnation values, respectively, were measured. In general, results obtained from semiempirical methods developed for each of the six types of interference agreed with the experimental peaks

Flow Control Applications

Flow control has a long history with many successes across a plethora of applications. This report addresses the characteristics of the approaches that are actually used, why they are used, the many approaches that are not used, and why. Analysis indicates ways forward to increase applicability/usefulness, and efficiency of flow control research. Overall, greater and more effective progress in flow control requires utilization of far more detailed information early in the research process regarding application details and requirements

Numerical solution of the Navier-Stokes equations about three-dimensional configurations: A survey

The numerical solution of the Navier-Stokes equations about three-dimensional configurations is reviewed. Formulational and computational requirements for the various Navier-Stokes approaches are examined for typical problems including the viscous flow field solution about a complete aerospace vehicle. Recent computed results, with experimental comparisons when available, are presented to highlight the presentation. The future of Navier-Stokes applications in three-dimensions is seen to be rapidly expanding across a broad front including internal and external flows, and flows across the entire speed regime from incompressible to hypersonic applications. Prospects for the future are described and recommendations for areas of concentrated research are indicated

Effects of a nonadiabatic wall on supersonic shock/boundary-layer interactions

Direct numerical simulations are employed to investigate a shock wave impinging on a turbulent boundary layer at free-stream Mach number M=2.28 with different wall thermal conditions, including adiabatic, cooled, and heated, for a wide range of deflection angles. It is found that the thermal boundary condition at the wall has a large effect on the size of the interaction region and on the level of pressure fluctuations. The distribution of the Stanton number shows a good agreement with prior experimental studies and confirms the strong heat transfer and complex pattern within the interaction region. An effort was also made to describe the unsteady features of the flow by means of wall pressure and heat flux spectra. Numerical results indicate that the changes in the interaction length due to the wall thermal condition are mainly linked to the incoming boundary layer, which is in agreement with previous experimental studies

Aeronautical engineering: A continuing bibliography, supplement 122

This bibliography lists 303 reports, articles, and other documents introduced into the NASA scientific and technical information system in April 1980