AirSync: Enabling Distributed Multiuser MIMO with Full Spatial Multiplexing

The enormous success of advanced wireless devices is pushing the demand for higher wireless data rates. Denser spectrum reuse through the deployment of more access points per square mile has the potential to successfully meet the increasing demand for more bandwidth. In theory, the best approach to density increase is via distributed multiuser MIMO, where several access points are connected to a central server and operate as a large distributed multi-antenna access point, ensuring that all transmitted signal power serves the purpose of data transmission, rather than creating "interference." In practice, while enterprise networks offer a natural setup in which distributed MIMO might be possible, there are serious implementation difficulties, the primary one being the need to eliminate phase and timing offsets between the jointly coordinated access points. In this paper we propose AirSync, a novel scheme which provides not only time but also phase synchronization, thus enabling distributed MIMO with full spatial multiplexing gains. AirSync locks the phase of all access points using a common reference broadcasted over the air in conjunction with a Kalman filter which closely tracks the phase drift. We have implemented AirSync as a digital circuit in the FPGA of the WARP radio platform. Our experimental testbed, comprised of two access points and two clients, shows that AirSync is able to achieve phase synchronization within a few degrees, and allows the system to nearly achieve the theoretical optimal multiplexing gain. We also discuss MAC and higher layer aspects of a practical deployment. To the best of our knowledge, AirSync offers the first ever realization of the full multiuser MIMO gain, namely the ability to increase the number of wireless clients linearly with the number of jointly coordinated access points, without reducing the per client rate.Comment: Submitted to Transactions on Networkin

Multi-stage Wireless Signal Identification for Blind Interception Receiver Design

Protection of critical wireless infrastructure from malicious attacks has become increasingly important in recent years, with the widespread deployment of various wireless technologies and dramatic growth in user populations. This brings substantial technical challenges to the interception receiver design to sense and identify various wireless signals using different transmission technologies. The key requirements for the receiver design include estimation of the signal parameters/features and classification of the modulation scheme. With the proper identification results, corresponding signal interception techniques can be developed, which can be further employed to enhance the network behaviour analysis and intrusion detection. In detail, the initial stage of the blind interception receiver design is to identify the signal parameters. In the thesis, two low-complexity approaches are provided to realize the parameter estimation, which are based on iterative cyclostationary analysis and envelope spectrum estimation, respectively. With the estimated signal parameters, automatic modulation classification (AMC) is performed to automatically identify the modulation schemes of the transmitted signals. A novel approach is presented based on Gaussian Mixture Models (GMM) in Chapter 4. The approach is capable of mitigating the negative effect from multipath fading channel. To validate the proposed design, the performance is evaluated under an experimental propagation environment. The results show that the proposed design is capable of adapting blind parameter estimation, realize timing and frequency synchronization and classifying the modulation schemes with improved performances

A low-cost time-hopping impulse radio system for high data rate transmission

We present an efficient, low-cost implementation of time-hopping impulse radio that fulfills the spectral mask mandated by the FCC and is suitable for high-data-rate, short-range communications. Key features are: (i) all-baseband implementation that obviates the need for passband components, (ii) symbol-rate (not chip rate) sampling, A/D conversion, and digital signal processing, (iii) fast acquisition due to novel search algorithms, (iv) spectral shaping that can be adapted to accommodate different spectrum regulations and interference environments. Computer simulations show that this system can provide 110Mbit/s at 7-10m distance, as well as higher data rates at shorter distances under FCC emissions limits. Due to the spreading concept of time-hopping impulse radio, the system can sustain multiple simultaneous users, and can suppress narrowband interference effectively.Comment: To appear in EURASIP Journal on Applied Signal Processing (Special Issue on UWB - State of the Art

Direction of Arrival Estimation for Radio Positioning: a Hardware Implementation Perspective

Nowadays multiple antenna wireless systems have gained considerable attention due to their capability to increase performance. Advances in theory have introduced several new schemes that rely on multiple antennas and aim to increase data rate, diversity gain, or to provide multiuser capabilities, beamforming and direction finding (DF) features. In this respect, it has been shown that a multiple antenna receiver can be potentially used to perform radio localization by using the direction of arrival (DoA) estimation technique. In this field, the literature is extensive and gathers the results of almost four decades of research activities. Among the most cited techniques that have been developed, we find the so called high-resolution algorithms, such as multiple signal classification (MUSIC), or estimation of signal parameters via rotational invariance (ESPRIT). Theoretical analysis as well as simulation results have demonstrated their excellent performance to the point that they are usually considered as reference for the comparison with other algorithms. However, such a performance is not necessarily obtained in a real system due to the presence of non idealities. These can be divided into two categories: the impairments due to the antenna array, and the impairments due to the multiple radio frequency (RF) and acquisition front-ends (FEs). The former are strongly influenced by the manufacturing accuracy and, depending on the required DoA resolution, have to be taken into account. Several works address these issues in the literature. The multiple FE non idealities, instead, are usually not considered in the DoA estimation literature, even if they can have a detrimental effect on the performance. This has motivated the research work in this thesis that addresses the problem of DoA estimation from a practical implementation perspective, emphasizing the impact of the hardware impairments on the final performance. This work is substantiated by measurements done on a state-of-the-art hardware platform that have pointed out the presence of non idealities such as DC offsets, phase noise (PN), carrier frequency offsets (CFOs), and phase offsets (POs) among receivers. Particularly, the hardware platform will be herein described and examined to understand what non idealities can affect the DoA estimation performance. This analysis will bring to identify which features a DF system should have to reach certain performance. Another important issue is the number of antenna elements. In fact, it is usually limited by practical considerations, such as size, costs, and also complexity. However, the most cited DoA estimation algorithms need a high number of antenna elements, and this does not yield them suitable to be implemented in a real system. Motivated by this consideration, the final part of this work will describe a novel DoA estimation algorithm that can be used when multipath propagation occurs. This algorithm does not need a high number of antenna elements to be implemented, and it shows good performance despite its low implementation/computational complexity

Algorithm-Architecture Co-Design for Digital Front-Ends in Mobile Receivers

The methodology behind this work has been to use the concept of algorithm-hardware co-design to achieve efficient solutions related to the digital front-end in mobile receivers. It has been shown that, by looking at algorithms and hardware architectures together, more efficient solutions can be found; i.e., efficient with respect to some design measure. In this thesis the main focus have been placed on two such parameters; first reduced complexity algorithms to lower energy consumptions at limited performance degradation, secondly to handle the increasing number of wireless standards that preferably should run on the same hardware platform. To be able to perform this task it is crucial to understand both sides of the table, i.e., both algorithms and concepts for wireless communication as well as the implications arising on the hardware architecture. It is easier to handle the high complexity by separating those disciplines in a way of layered abstraction. However, this representation is imperfect, since many interconnected "details" belonging to different layers are lost in the attempt of handling the complexity. This results in poor implementations and the design of mobile terminals is no exception. Wireless communication standards are often designed based on mathematical algorithms with theoretical boundaries, with few considerations to actual implementation constraints such as, energy consumption, silicon area, etc. This thesis does not try to remove the layer abstraction model, given its undeniable advantages, but rather uses those cross-layer "details" that went missing during the abstraction. This is done in three manners: In the first part, the cross-layer optimization is carried out from the algorithm perspective. Important circuit design parameters, such as quantization are taken into consideration when designing the algorithm for OFDM symbol timing, CFO, and SNR estimation with a single bit, namely, the Sign-Bit. Proof-of-concept circuits were fabricated and showed high potential for low-end receivers. In the second part, the cross-layer optimization is accomplished from the opposite side, i.e., the hardware-architectural side. A SDR architecture is known for its flexibility and scalability over many applications. In this work a filtering application is mapped into software instructions in the SDR architecture in order to make filtering-specific modules redundant, and thus, save silicon area. In the third and last part, the optimization is done from an intermediate point within the algorithm-architecture spectrum. Here, a heterogeneous architecture with a combination of highly efficient and highly flexible modules is used to accomplish initial synchronization in at least two concurrent OFDM standards. A demonstrator was build capable of performing synchronization in any two standards, including LTE, WiFi, and DVB-H

Measurement, Modeling, and OFDM Synchronization for the Wideband Mobile-to-Mobile Channel

Wideband measurements of the mobile-to-mobile channel, especially of the harshest channels, are necessary for proper design and certification testing of mobile-to-mobile communications systems. A complete measurement implies that the Doppler and delay characteristics are measured jointly. However, such measurements have not previously been published. The main objective of the proposed research is to develop channel models for specific scenarios from data obtained in a wideband mobile-to-mobile measurement campaign in the 5.9 GHz frequency band. For this purpose we developed a channel sounding system including a novel combined waveform. In order to quantify and qualify either the recorded channel or the proposed generated channel, we developed a simulation test-bed that includes all the characteristics of the proposed digital short range communications (DSRC) standard. The resulting channel models needed to comply with the specifications required by hardware channel emulators or software channel simulators. From the obtained models, we selected one to be included in the IEEE 802.11p standard certification test. To further aid in the development of software radio based receivers, we also developed an orthogonal frequency division multiplexing (OFDM) synchronization algorithm to analyze and compensate synchronization errors produced by inaccessible system clocks.Ph.D.Committee Chair: Ingram, Mary Ann; Committee Member: Lanterman, Aaron; Committee Member: Li, Ye; Committee Member: Pratt, Thomas G.; Committee Member: Rogers, Peter H

Doctor of Philosophy

dissertationWireless communications pervade all avenues of modern life. The rapid expansion of wireless services has increased the need for transmission schemes that are more spectrally efficient. Dynamic spectrum access (DSA) systems attempt to address this need by building a network where the spectrum is used opportunistically by all users based on local and regional measurements of its availability. One of the principal requirements in DSA systems is to initialize and maintain a control channel to link the nodes together. This should be done even before a complete spectral usage map is available. Additionally, with more users accessing the spectrum, it is important to maintain a stable link in the presence of significant interference in emergency first-responders, rescue, and defense applications. In this thesis, a new multicarrier spread spectrum (MC-SS) technique based on filter banks is presented. The new technique is called filter bank multicarrier spread spectrum (FB-MC-SS). A detailed theory of the underlying properties of this signal are given, with emphasis on the properties that lend themselves to synchronization at the receiver. Proposed algorithms for synchronization, channel estimation, and detection are implemented on a software-defined radio platform to complete an FB-MC-SS transceiver and to prove the practicality of the technique. FB-MC-SS is shown through physical experimentation to be significantly more robust to partial band interference compared to direct sequence spread spectrum. With a higher power interfering signal occupying 90% of its band, FB-MC-SS maintains a low bit error rate. Under the same interference conditions, DS-SS fails completely. This experimentation leads to a theoretical analysis that shows in a frequency selective channel with additive white noise, the FB-MC-SS system has performance that equals that obtained by a DS-SS system employing an optimal rake receiver. This thesis contains a detailed chapter on implementation and design, including lessons learned while prototyping the system. This is to assist future system designers to quickly gain proficiency in further development of this technology