Robust low-power digital circuit design in nano-CMOS technologies

Device scaling has resulted in large scale integrated, high performance, low-power, and low cost systems. However the move towards sub-100 nm technology nodes has increased variability in device characteristics due to large process variations. Variability has severe implications on digital circuit design by causing timing uncertainties in combinational circuits, degrading yield and reliability of memory elements, and increasing power density due to slow scaling of supply voltage. Conventional design methods add large pessimistic safety margins to mitigate increased variability, however, they incur large power and performance loss as the combination of worst cases occurs very rarely. In-situ monitoring of timing failures provides an opportunity to dynamically tune safety margins in proportion to on-chip variability that can significantly minimize power and performance losses. We demonstrated by simulations two delay sensor designs to detect timing failures in advance that can be coupled with different compensation techniques such as voltage scaling, body biasing, or frequency scaling to avoid actual timing failures. Our simulation results using 45 nm and 32 nm technology BSIM4 models indicate significant reduction in total power consumption under temperature and statistical variations. Future work involves using dual sensing to avoid useless voltage scaling that incurs a speed loss. SRAM cache is the first victim of increased process variations that requires handcrafted design to meet area, power, and performance requirements. We have proposed novel 6 transistors (6T), 7 transistors (7T), and 8 transistors (8T)-SRAM cells that enable variability tolerant and low-power SRAM cache designs. Increased sense-amplifier offset voltage due to device mismatch arising from high variability increases delay and power consumption of SRAM design. We have proposed two novel design techniques to reduce offset voltage dependent delays providing a high speed low-power SRAM design. Increasing leakage currents in nano-CMOS technologies pose a major challenge to a low-power reliable design. We have investigated novel segmented supply voltage architecture to reduce leakage power of the SRAM caches since they occupy bulk of the total chip area and power. Future work involves developing leakage reduction methods for the combination logic designs including SRAM peripherals

Temperature Variation Operation of Mixed-VT 3T GC-eDRAM for Low Power Applications in 2Kbit Memory Array

Embedded memories were once utilized to transfer information between the CPU and the main memory. The cache storage in most traditional computers was static-random-access-memory (SRAM). Other memory technologies, such as embedded dynamic random-access memory (eDRAM) and spin-transfer-torque random-access memory (STT-RAM), have also been used to store cache data. The SRAM, on the other hand, has a low density and severe leakage issues, and the STT-RAM has high latency and energy consumption when writing. The gain-cell eDRAM (GC-eDRAM), which has a higher density, lower leakage, logic compatibility, and is appropriate for two-port operations, is an attractive option. To speed up data retrieval from the main memory, future processors will require larger and faster-embedded memories. Area overhead, power overhead, and speed performance are all issues with the existing architecture. A unique mixed-V_T 3T GC-eDRAM architecture is suggested in this paper to improve data retention times (DRT) and performance for better energy efficiency in embedded memories. The GC-eDRAM is simulated using a standard complementary-metal-oxide-semiconductor (CMOS) with a 130nm technology node transistor. The performance of a 2kbit mixed-V_T 3T GC-eDRAM array were evaluated through corner process simulations. Each memory block is designed and simulated using Mentor Graphics Software. The array, which is based on the suggested bit-cell, has been successfully operated at 400Mhz under a 1V supply and takes up almost 60-75% less space than 6T SRAM using the same technology. When compared to the existing 6T and 4T ULP SRAMs (others' work), the retention power of the proposed GC-eDRAM is around 80-90% lower

Exploiting Inter- and Intra-Memory Asymmetries for Data Mapping in Hybrid Tiered-Memories

Modern computing systems are embracing hybrid memory comprising of DRAM and non-volatile memory (NVM) to combine the best properties of both memory technologies, achieving low latency, high reliability, and high density. A prominent characteristic of DRAM-NVM hybrid memory is that it has NVM access latency much higher than DRAM access latency. We call this inter-memory asymmetry. We observe that parasitic components on a long bitline are a major source of high latency in both DRAM and NVM, and a significant factor contributing to high-voltage operations in NVM, which impact their reliability. We propose an architectural change, where each long bitline in DRAM and NVM is split into two segments by an isolation transistor. One segment can be accessed with lower latency and operating voltage than the other. By introducing tiers, we enable non-uniform accesses within each memory type (which we call intra-memory asymmetry), leading to performance and reliability trade-offs in DRAM-NVM hybrid memory. We extend existing NVM-DRAM OS in three ways. First, we exploit both inter- and intra-memory asymmetries to allocate and migrate memory pages between the tiers in DRAM and NVM. Second, we improve the OS's page allocation decisions by predicting the access intensity of a newly-referenced memory page in a program and placing it to a matching tier during its initial allocation. This minimizes page migrations during program execution, lowering the performance overhead. Third, we propose a solution to migrate pages between the tiers of the same memory without transferring data over the memory channel, minimizing channel occupancy and improving performance. Our overall approach, which we call MNEME, to enable and exploit asymmetries in DRAM-NVM hybrid tiered memory improves both performance and reliability for both single-core and multi-programmed workloads.Comment: 15 pages, 29 figures, accepted at ACM SIGPLAN International Symposium on Memory Managemen

Energy Reduction Techniques to Increase Battery Life for Electronic Sensor Nodes

Preserving battery life in duty-cycled sensor nodes requires minimizing energy use in the active region. Lowering the power supply of CMOS gates down into sub-threshold mode is a good way to decrease energy. In this work, a unique technique to control the current in CMOS gates to reliably operate them in sub-threshold mode is described. Compared to the current state-of-theart for running digital gates in the sub-threshold regime, this work is often superior in its lack of complexity and in reduced variance in delay caused by process variations. In addition to presenting the design considerations, a demonstration of a complete digital design flow is given using the custom gates. An AES128 encryption/decryption engine is designed using the aforementioned digital flow in a commercial 180nm process. The resulting design has a ratio of maximum to minimum frequency variation over corners of only 50% with a 0.3V power supply where the same ratio with standard CMOS gates biased under the same supply voltage is 5600%. In addition, the custom gates are used to design a Wallace tree multiplier in an SOI 45nm process that is fully functional with an optimum energy power supply level of 0.34V with a typical operating frequency of 8 MHz having a variation over corners of 80%. For a proof of concept memory chip designed in this work, the architecture uses a logiccompatible CMOS process particularly suitable for embedded applications. The differential pair construct causes the read and refresh power to be independent of any process parameter including the within-die threshold voltage. The current stop feature keeps the read voltage transition low to further minimize read power. The bit cell operates in both single bit BASE2 and multi-bit BASE4 modes. An expression for the read signal was verified with bit cell simulations. These simulations also compare the performance impact of threshold voltage variance in the architecture with a standard gain cell. A DRAM bit cell array was fabricated in the XFab 180nm CMOS process. Measured waveforms closely match theoretical results obtained from a system simulation. The silicon retention time was measured at room temperature and is greater than 150 ms in BASE2 mode and greater than 75 ms in BASE4 mode. 180nm, 25C analysis predicts 0.8uW/Mbit refresh power at 630 MHz, the lowest in the literature. Further: the memory bit cell architecture presented here has a refresh power delay product several times lower than any other published architecture. The current controlled memory architecture in this work improves or overcomes the drawbacks of the 1T1C and gain cell memory architectures. A current controlled memory design was fabricated as a 131K bit array in an 180nm process to provide silicon proof. The bit cell configuration with shared read and write bit cells gives effectively two memory banks. The grouping of rows together into common source domains allows only two opamps to control the current in all the bit cells across the whole chip. The sense amplifiers have a globally controlled switching threshold point and keep their static power in the nano-amp range. The bit cells can operate either in BASE2 or BASE4 mode and the read bit line transitions are reduced with a current stop construct. Parts were received from the foundry in an 84-pin PLCC and were tested at a number of locations on the die. They proved to be fully functional in BASE4. The silicon retention time was measured at room temperature and was greater than four seconds

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

Low-power and high-performance SRAM design in high variability advanced CMOS technology

As process technologies shrink, the size and number of memories on a chip are exponentially increasing. Embedded SRAMs are a critical component in modern digital systems, and they strongly impact the overall power, performance, and area. To promote memory-related research in academia, this dissertation introduces OpenRAM, a flexible, portable and open-source memory compiler and characterization methodology for generating and verifying memory designs across different technologies.In addition, SRAM designs, focusing on improving power consumption, access time and bitcell stability are explored in high variability advanced CMOS technologies. To have a stable read/write operation for SRAM in high variability process nodes, a differential-ended single-port 8T bitcell is proposed that improves the read noise margin, write noise margin and readout bitcell current by 45%, 48% and 21%, respectively, compared to a conventional 6T bitcell. Also, a differential-ended single-port 12T bitcell for subthreshold operation is proposed that solves the half-select disturbance and allows efficient bit-interleaving. 12T bitcell has a leakage control mechanism which helps to reduce the power consumption and provides operation down to 0.3 V. Both 8T and 12T bitcells are analyzed in a 64 kb SRAM array using 32 nm technology. Besides, to further improve the access time and power consumption, two tracking circuits (multi replica bitline delay and reconfigurable replica bitline delay techniques) are proposed to aid the generation of accurate and optimum sense amplifier set time.An error tolerant SRAM architecture suitable for low voltage video application with dynamic power-quality management is also proposed in this dissertation. This memory uses three power supplies to improve the SRAM stability in low voltages. The proposed triple-supply approach achieves 63% improvement in image quality and 69% reduction in power consumption compared to a single-supply 64 kb SRAM array at 0.70 V