33 research outputs found
The performance of phaselocked loops for frequency control in single sideband land mobile radio receivers.
SIGLELD:D49169/84 / BLDSC - British Library Document Supply CentreGBUnited Kingdo
Low jitter phase-locked loop clock synthesis with wide locking range
The fast growing demand of wireless and high speed data communications has driven efforts to increase the levels of integration in many communications applications. Phase noise and timing jitter are important design considerations for these communications applications. The desire for highly complex levels of integration using low cost CMOS technologies works against the minimization of timing jitter and phase noise for communications systems which employ a phase-locked loop for frequency and clock synthesis with on-chip VCO. This dictates an integrated CMOS implementation of the VCO with very low phase noise performance. The ring oscillator VCOs based on differential delay cell chains have been used successfully in communications applications, but thermal noise induced phase noise have to be minimized in order not to limit their applicability to some applications which impose stringent timing jitter and phase noise requirements on the PLL clock synthesizer. Obtaining lower timing jitter and phase noise at the PLL output also requires the minimization of noise in critical circuit design blocks as well as the optimization of the loop bandwidth of the PLL.
In this dissertation the fundamental performance limits of CMOS PLL clock synthesizers based on ring oscillator VCOs are investigated. The effect of flicker and thermal noise in MOS transistors on timing jitter and phase noise are explored, with particular emphasis on source coupled NMOS differential delay cells with symmetric load elements. Several new circuit architectures are employed for the charge pump circuit and phase-frequency detector (PFD) to minimize the timing jitter due to the finite dead zone in the PFD and the current mismatch in the charge pump circuit. The selection of the optimum PLL loop bandwidth is critical in determining the phase noise performance at the PLL output. The optimum loop bandwidth and the phase noise performance of the PLL is determined using behavioral simulations. These results are compared with transistor level simulated results and experimental results for the PLL clock synthesizer fabricated in a 0.35 µm CMOS technology with good agreement.
To demonstrate the proposed concept, a fully integrated CMOS PLL clock synthesizer utilizing integer-N frequency multiplier technique to synthesize several clock signals in the range of 20-400 MHz with low phase noise was designed. Implemented in a standard 0.35-µm N-well CMOS process technology, the PLL achieves a period jitter of 6.5-ps (rms) and 38-ps (peak-to-peak) at 216 MHz with a phase noise of -120 dBc/Hz at frequency offsets above 10 KHz.
The specific research contributions of this work include (1) proposing, designing, and implementing a new charge pump circuit architecture that matches current levels and therefore minimizes one source of phase noise due to fluctuations in the control voltage of the VCO, (2) an improved phase-frequency detector architecture which has improved characteristics in lock condition, (3) an improved ring oscillator VCO with excellent thermal noise induced phase noise characteristics, (4) the application of selfbiased techniques together with fixed bias to CMOS low phase noise PLL clock synthesizer for digital video communications ,and (5) an analytical model that describes the phase noise performance of the proposed VCO and PLL clock synthesizer
Design of a microprocessor based instrumentation module for signal processing applications
Call number: LD2668 .T4 1984 R35Master of Scienc
Automated transfer function measurements
Call number: LD2668 .T4 EECE 1989 R36Master of ScienceElectrical and Computer Engineerin
DESIGN AND CHARACTERIZATION OF LOW-POWER LOW-NOISE ALLDIGITAL SERIAL LINK FOR POINT-TO-POINT COMMUNICATION IN SOC
The fully-digital implementation of serial links has recently emerged as a viable
alternative to their classical analogue counterpart. Indeed, reducing the analogue
content in favour of expanding the digital content becomes more attractive due to the
ability to achieve less power consumption, less sensitivity to the noise and better
scalability across multiple technologies and platforms with inconsiderable
modifications. In addition, describing the circuit in hardware description languages
gives it a high flexibility to program all design parameters in a very short time
compared with the analogue designs which need to be re-designed at transistor level
for any parameter change. This can radically reduce cost and time-to-market by
saving a significant amount of development time. However, beside these considerable
advantages, the fully-digital architecture poses several design challenges
Analysis of Offset Pulse Position Modulation
This work presents the performance analysis of the offset pulse position modulation (PPM) scheme using graded-index plastic optical fibre with a Gaussian impulse response. The aim of this analysis is to predict how sensitivity, error, number of required photons, threshold voltage, and the effect of inter-symbol interference will change with the change in the number of data bits encoded at a rate of 1 Gbit/s. An information theory analysis is presented in detail and also the band-utilization efficiency is determined. Results are compared to equivalent digital PPM and multiple PPM schemes and it is also shown that offset PPM gives an advantage over on-off keying (OOK).
Bit error rate (BER) analysis has been presented numerically. The errors due to different coding techniques are compared. It has also been shown that offset pulse position modulation is more power efficient than multiple pulse position modulation. The spectral analysis of offset pulse position modulation coding scheme has been carried out. For an offset PPM sequence the spectral characteristics is presented both theoretically and numerically. The results show strong frequency components at the frame rate and, if return-to-zero pulses are used, the slot rate. Slot synchronisation has been taken into consideration for the first time as offset PPM spectrum exhibits discrete slot rate component. The effect of pulse shaping and modulating index on the spectrum has been shown. The dependency of slot component on the pulse shape is examined. The results show that the frame synchronisation is possible for offset PPM as this coding exhibits a strong frame rate component. A comparison of spectral characteristics has been presented considering digital, multiple and shortened PPM. For ease of implementation an offset PPM coder has been designed. In this work an efficient clock recovery topology is presented for offset PPM data sequence at the receiver end. For clock recovery, a phase locked loop is designed. Data recovery has also been presented. It is shown that a frame clock can be extracted from the data sequence that yields the possibility of frame synchronization. A detailed noise analysis has been performed for random offset PPM input.
It has been shown that the proposed clock recovery system is also effective for extracting other data sequence. To elucidate, a multiple Pulse Position Modulation (MPPM) data sequence is considered. The MPPM data sequence has also been synchronised with the recovered clock. A noise analysis is carried out for multiple PPM
Recommended from our members
CMOS Signal Synthesizers for Emerging RF-to-Optical Applications
The need for clean and powerful signal generation is ubiquitous, with applications spanning the spectrum from RF to mm-Wave, to into and beyond the terahertz-gap. RF applications including mobile telephony and microprocessors have effectively harnessed mixed-signal integration in CMOS to realize robust on-chip signal sources calibrated against adverse ambient conditions. Combined with low cost and high yield, the CMOS component of hand-held devices costs a few cents per part per million parts. This low cost, and integrated digital processing, make CMOS an attractive option for applications like high-resolution imaging and ranging, and the emerging 5-G communication space. RADAR techniques when expanded to optical frequencies can enable micrometers of resolution for 3D imaging. These applications, however, impose upto 100x more exacting specifications on power and spectral purity at much higher frequencies than conventional RF synthesizers.
This generation of applications will present unconventional challenges for transistor technologies - whether it is to squeeze performance in the conventionally used spectrum, already wrung dry, or signal generation and system design in the relatively emptier mm-Wave to sub-mmWave spectrum, much of the latter falling in the ``Terahertz Gap". Indeed, transistor scaling and innovative device physics leading to new transistor topologies have yielded higher cut-off frequencies in CMOS, though still lagging well behind SiGe and III-V semiconductors. To avoid multimodule solutions with functionality partitioned across different technologies, CMOS must be pushed out of its comfort zone, and technology scaling has to have accompanying breakthroughs in design approaches not only at the system but also at the block level. In this thesis, while not targeting a specific application, we seek to formulate the obstacles in synthesizing high frequency, high power and low noise signals in CMOS and construct a coherent design methodology to address them. Based on this, three novel prototypes to overcome the limiting factors in each case are presented.
The first half of this thesis deals with high frequency signal synthesis and power generation in CMOS. Outside the range of frequencies where the transistor has gain, frequency generation necessitates harmonic extraction either as harmonic oscillators or as frequency multipliers. We augment the traditional maximum oscillation frequency metric (fmax), which only accounts for transistor losses, with passive component loss to derive an effective fmax metric. We then present a methodology for building oscillators at this fmax, the Maximum Gain Ring Oscillator. Next, we explore generating large signals beyond fmax through harmonic extraction in multipliers. Applying concepts of waveform shaping, we demonstrate a Power Mixer that engineers transistor nonlinearity by manipulating the amplitudes and relative phase shifts of different device nodes to maximize performance at a specific harmonic beyond device cut-off.
The second half proposes a new architecture for an ultra-low noise phase-locked loop (PLL), the Reference-Sampling PLL. In conventional PLLs, a noisy buffer converts the slow, low-noise sine-wave reference signal to a jittery square-wave clock against which the phase of a noisy voltage-controlled oscillator (VCO) is corrected. We eliminate this reference buffer, and measure phase error by sampling the reference sine-wave with the 50x faster VCO waveform already available on chip, and selecting the relevant sample with voltage proportional to phase error. By avoiding the N-squared multiplication of the high-power reference buffer noise, and directly using voltage-mode phase error to control the VCO, we eliminate several noisy components in the controlling loop for ultra-low integrated jitter for a given power consumption. Further, isolation of the VCO tank from any varying load, unlike other contemporary divider-less PLL architectures, results in an architecture with record performance in the low-noise and low-spur space.
We conclude with work that brings together concepts developed for clean, high-power signal generation towards a hybrid CMOS-Optical approach to Frequency-Modulated Continuous-Wave (FMCW) Light-Detection-And-Ranging (LIDAR). Cost-effective tunable lasers are temperature-sensitive and have nonlinear tuning profiles, rendering precise frequency modulations or 'chirps' untenable. Locking them to an electronic reference through an electro-optic PLL, and electronically calibrating the control signal for nonlinearity and ambient sensitivity, can make such chirps possible. Approaches that build on the body of advances in electrical PLLs to control the performance, and ease the specification on the design of optical systems are proposed. Eventually, we seek to leverage the twin advantages of silicon-intensive integration and low-cost high-yield towards developing a single-chip solution that uses on-chip signal processing and phased arrays to generate precise and robust chirps for an electronically-steerable fine LIDAR beam