Automated pick-up of suturing needles for robotic surgical assistance

Robot-assisted laparoscopic prostatectomy (RALP) is a treatment for prostate cancer that involves complete or nerve sparing removal prostate tissue that contains cancer. After removal the bladder neck is successively sutured directly with the urethra. The procedure is called urethrovesical anastomosis and is one of the most dexterity demanding tasks during RALP. Two suturing instruments and a pair of needles are used in combination to perform a running stitch during urethrovesical anastomosis. While robotic instruments provide enhanced dexterity to perform the anastomosis, it is still highly challenging and difficult to learn. In this paper, we presents a vision-guided needle grasping method for automatically grasping the needle that has been inserted into the patient prior to anastomosis. We aim to automatically grasp the suturing needle in a position that avoids hand-offs and immediately enables the start of suturing. The full grasping process can be broken down into: a needle detection algorithm; an approach phase where the surgical tool moves closer to the needle based on visual feedback; and a grasping phase through path planning based on observed surgical practice. Our experimental results show examples of successful autonomous grasping that has the potential to simplify and decrease the operational time in RALP by assisting a small component of urethrovesical anastomosis

Fast and Reliable Autonomous Surgical Debridement with Cable-Driven Robots Using a Two-Phase Calibration Procedure

Automating precision subtasks such as debridement (removing dead or diseased tissue fragments) with Robotic Surgical Assistants (RSAs) such as the da Vinci Research Kit (dVRK) is challenging due to inherent non-linearities in cable-driven systems. We propose and evaluate a novel two-phase coarse-to-fine calibration method. In Phase I (coarse), we place a red calibration marker on the end effector and let it randomly move through a set of open-loop trajectories to obtain a large sample set of camera pixels and internal robot end-effector configurations. This coarse data is then used to train a Deep Neural Network (DNN) to learn the coarse transformation bias. In Phase II (fine), the bias from Phase I is applied to move the end-effector toward a small set of specific target points on a printed sheet. For each target, a human operator manually adjusts the end-effector position by direct contact (not through teleoperation) and the residual compensation bias is recorded. This fine data is then used to train a Random Forest (RF) to learn the fine transformation bias. Subsequent experiments suggest that without calibration, position errors average 4.55mm. Phase I can reduce average error to 2.14mm and the combination of Phase I and Phase II can reduces average error to 1.08mm. We apply these results to debridement of raisins and pumpkin seeds as fragment phantoms. Using an endoscopic stereo camera with standard edge detection, experiments with 120 trials achieved average success rates of 94.5%, exceeding prior results with much larger fragments (89.4%) and achieving a speedup of 2.1x, decreasing time per fragment from 15.8 seconds to 7.3 seconds. Source code, data, and videos are available at https://sites.google.com/view/calib-icra/.Comment: Code, data, and videos are available at https://sites.google.com/view/calib-icra/. Final version for ICRA 201

Combining Self-Supervised Learning and Imitation for Vision-Based Rope Manipulation

Manipulation of deformable objects, such as ropes and cloth, is an important but challenging problem in robotics. We present a learning-based system where a robot takes as input a sequence of images of a human manipulating a rope from an initial to goal configuration, and outputs a sequence of actions that can reproduce the human demonstration, using only monocular images as input. To perform this task, the robot learns a pixel-level inverse dynamics model of rope manipulation directly from images in a self-supervised manner, using about 60K interactions with the rope collected autonomously by the robot. The human demonstration provides a high-level plan of what to do and the low-level inverse model is used to execute the plan. We show that by combining the high and low-level plans, the robot can successfully manipulate a rope into a variety of target shapes using only a sequence of human-provided images for direction.Comment: 8 pages, accepted to International Conference on Robotics and Automation (ICRA) 201

Perception of Deformable Objects and Compliant Manipulation for Service Robots

Abstract We identified softness in robot control as well as robot perception as key enabling technologies for future service robots. Compliance in motion control compensates for small errors in model acquisition and estimation and enables safe physical interaction with humans. The perception of shape similarities and defor-mations allows a robot to adapt its skills to the object at hand, given a description of the skill that generalizes between different objects. In this paper, we present our approaches to compliant control and object manipulation skill transfer for service robots. We report on evaluation results and public demonstrations of our ap-proaches. 1

Robot Assisted Object Manipulation for Minimally Invasive Surgery

Robotic systems have an increasingly important role in facilitating minimally invasive surgical treatments. In robot-assisted minimally invasive surgery, surgeons remotely control instruments from a console to perform operations inside the patient. However, despite the advanced technological status of surgical robots, fully autonomous systems, with decision-making capabilities, are not yet available. In 2017, a structure to classify the research efforts toward autonomy achievable with surgical robots was proposed by Yang et al. Six different levels were identified: no autonomy, robot assistance, task autonomy, conditional autonomy, high autonomy, and full autonomy. All the commercially available platforms in robot-assisted surgery is still in level 0 (no autonomy). Despite increasing the level of autonomy remains an open challenge, its adoption could potentially introduce multiple benefits, such as decreasing surgeons’ workload and fatigue and pursuing a consistent quality of procedures. Ultimately, allowing the surgeons to interpret the ample and intelligent information from the system will enhance the surgical outcome and positively reflect both on patients and society. Three main aspects are required to introduce automation into surgery: the surgical robot must move with high precision, have motion planning capabilities and understand the surgical scene. Besides these main factors, depending on the type of surgery, there could be other aspects that might play a fundamental role, to name some compliance, stiffness, etc. This thesis addresses three technological challenges encountered when trying to achieve the aforementioned goals, in the specific case of robot-object interaction. First, how to overcome the inaccuracy of cable-driven systems when executing fine and precise movements. Second, planning different tasks in dynamically changing environments. Lastly, how the understanding of a surgical scene can be used to solve more than one manipulation task. To address the first challenge, a control scheme relying on accurate calibration is implemented to execute the pick-up of a surgical needle. Regarding the planning of surgical tasks, two approaches are explored: one is learning from demonstration to pick and place a surgical object, and the second is using a gradient-based approach to trigger a smoother object repositioning phase during intraoperative procedures. Finally, to improve scene understanding, this thesis focuses on developing a simulation environment where multiple tasks can be learned based on the surgical scene and then transferred to the real robot. Experiments proved that automation of the pick and place task of different surgical objects is possible. The robot was successfully able to autonomously pick up a suturing needle, position a surgical device for intraoperative ultrasound scanning and manipulate soft tissue for intraoperative organ retraction. Despite automation of surgical subtasks has been demonstrated in this work, several challenges remain open, such as the capabilities of the generated algorithm to generalise over different environment conditions and different patients

A Comparison of Assistive Methods for Suturing in MIRS

In Minimally Invasive Robotic Surgery (MIRS) a robot is interposed between the surgeon and the surgical site to increase the precision, dexterity, and to reduce surgeon's effort and cognitive load with respect to the standard laparoscopic interventions. However, the modern robotic systems for MIRS are still based on the traditional telemanipulation paradigm, e.g. the robot behaviour is fully under surgeon's control, and no autonomy or assistance is implemented. In this work, supervised and shared controllers have been developed in a vision-free, human-in-the-Ioop, control framework to help surgeon during a surgical suturing procedure. Experiments conducted on the da Vinci Research Kit robot proves the effectiveness of the method indicating also the guidelines for improving results

A Cognitive Robot Control Architecture for Autonomous Execution of Surgical Tasks

The research on medical robotics is starting to address the autonomous execution of surgical tasks, without effective intervention of humans apart from supervision and task configuration. This paper addresses the complete automation of a surgical robot by combining advanced sensing, cognition and control capabilities, developed according to rigorous assessment of surgical require- ments, formal specification of robotic system behavior and software design and implementation based on solid tools and frame- works. In particular, the paper focuses on the cognitive control architecture and its development process, based on formal modeling and verification methods as best practices to ensure safe and reliable behavior. Full implementation of the proposed architecture has been tested on an experimental setup including a novel robot specifically designed for surgical applications, but adaptable to different selected tasks (i.e. needle insertion, wound suturing)