A DHT-based approach for path selection and message forwarding in IEEE 802.11s industrial wireless mesh networks

Wireless Mesh Networks (WMNs) are a promising communication technology that may offer greater flexibility and reliability, when compared to traditional wireless networks. WMNs open up new applications domains, but still need to find efficient mechanisms to deal with scalability and timeliness requirements. This paper proposes a scheme for Path Selection and Message Forwarding in IEEE 802.11s networks, that is suitable to be used in industrial environments. We present the DHT-based Cluster Routing Protocol (DCRP), a routing protocol based on DHTs, clustering of nodes and use of proxies. DCRP allows to improve the overall network performance by reducing the time required for path selection and the number of communication hops in large sized networks

Efficient redundancy in wired and wireless S2A architectures for NCS

This thesis focuses on the integration of wired and wireless nodes running on top of Gigabit Ethernet and WiFi respectively in Networked Control Systems. Such a networked control system investigated in this work consists of two wireless sensors, two wireless actuators, 14 wired sensors, two wired actuators and one wired supervisor. The architecture is based on Sensor-To-Actuator model. It is revealed through OMNeT++ simulations that the wired and wireless packet end-to-end delays in the developed model satisfy system requirements with no packet loss. Moreover, wired, wireless and mixed interferences are studied and quantified. The amount of interference that the model can withstand is determined. All results are subjected to a 95% confidence analysis. Additionally, the thesis focuses on reliability in the design of networked control systems that is becoming greatly important. Fault-tolerance is often used to increase system reliability. In this work, Triple Modular Redundancy (TMR) and Parallel Redundancy Protocol (PRP) are both applied to a Sensor-to-Actuator architecture with 16 sensors, four Actuators and one Supervisor. Two of the 16 sensors as well as two of the four actuators are wireless while the rest of the nodes are wired. It is first shown that this NCS succeeds in meeting all control system requirements (zero packet loss and bounded end-to-end delay). Reliability models are then developed to help designers choose the appropriate mix of fault-tolerant techniques in order to maximize lifetime while at the same time minimizing the extra cost due to the added redundancy

Networked control systems for intelligent transportation systems and industrial automation

This thesis presents a study of two different applications of Networked Control Systems. The first is: Ethernet Networked Control System On-board of Train-wagons. An Ethernet backbone is shared between control and entertainment. The wagon contains a dedicated control server and a dedicated entertainment server, which act as fault-tolerant machines for one another. In the event of a server failure, the remaining machine can serve both entertainment and/or control. The study aims at enhancing system design in order to maximize the tolerable entertainment load in the event of a control/entertainment server failure, while not causing any control violations. This fault-tolerant system is mathematically analyzed using a performability model to relate failure rates, enhancements and rewards. The model is taken further to test two identical wagons, with a total of four fault-tolerant servers. All possible failure sequences are simulated and a different communication philosophy is tested to further minimize the degradation of the entertainment load supported during the failure of up to three of the four servers. The system is shown to be capable of operating with minimal degradation with one out of four servers. The second is: Wireless Networked Control Systems (WNCS) for Industrial Automation. A WNCS using standard 802.11 and 802.3 protocols for communication is presented. Wireless Interface for Sensors and Actuators (WISA) by ABB is used as a benchmark for comparison. The basic unit is a single workcell, however, there is a need to cascade several cells along a production line. Simulations are conducted and a nontraditional allocation scheme is used to ensure correct operation under the effect of co-channel interference and network congestion. Next, fault-tolerance at the controller level is investigated due to the importance of minimizing downtime resulting from controller failure. Two different techniques of interconnecting neighboring cells are investigated. The study models both a two and three-cell scenario, and all systems show that fault-tolerance is achievable. This is mathematically studied using a performability analysis to relate failure rates with rewards at each failure state. All simulations are conducted on OPNET Network Modeler and results are subjected to a 95% confidence analysis

Hierarchical fault tolerance in wireless networked control systems

Wireless Networked Control Systems (WNCS) have recently emerged as a replacement for wired control networks. Wireless networked control systems are more suitable for environments that require higher flexibility and robustness. In previous literature a wireless manufacturing line was proposed. The work-cells communication was through IEEE 802.11 technologies and a switched Ethernet backbone. This thesis is aiming to improve the current solution by adding a supervisor to the existing system. The supervisor could be either in passive or active mode. Passive supervisor would intervene when all controllers in the network fail, while active supervisor would act once any controller on the line fail. The system was simulated using OPNET software with 95% confidence analysis. The ability of the system to withstand external interference was assessed through adding a single band jammer to the OPNET simulation. The system was able to hold up to 8KB interfering file sent from a single band jammer affecting the full Wi-Fi spectrum. All results were subjected to a 95% confidence analysis The performability of passive and active supervisor systems was compared. A Markov model of both systems was built. It was shown that by time, the performability of a passive supervisor system is enhanced while that of an active supervisor system degraded. However, the active supervisor showed a better performability in all cases