Time-Domain/Digital Frequency Synchronized Hysteresis Based Fully Integrated Voltage Regulator

abstract: Power management integrated circuit (PMIC) design is a key module in almost all electronics around us such as Phones, Tablets, Computers, Laptop, Electric vehicles, etc. The on-chip loads such as microprocessors cores, memories, Analog/RF, etc. requires multiple supply voltage domains. Providing these supply voltages from off-chip voltage regulators will increase the overall system cost and limits the performance due to the board and package parasitics. Therefore, an on-chip fully integrated voltage regulator (FIVR) is required. The dissertation presents a topology for a fully integrated power stage in a DC-DC buck converter achieving a high-power density and a time-domain hysteresis based highly integrated buck converter. A multi-phase time-domain comparator is proposed in this work for implementing the hysteresis control, thereby achieving a process scaling friendly highly digital design. A higher-order LC notch filter along with a flying capacitor which couples the input and output voltage ripple is implemented. The power stage operates at 500 MHz and can deliver a maximum power of 1.0 W and load current of 1.67 A, while occupying 1.21 mm2 active die area. Thus achieving a power density of 0.867 W/mm2 and current density of 1.377 A/mm2. The peak efficiency obtained is 71% at 780 mA of load current. The power stage with the additional off-chip LC is utilized to design a highly integrated current mode hysteretic buck converter operating at 180 MHz. It achieves 20 ns of settling and 2-5 ns of rise/fall time for reference tracking. The second part of the dissertation discusses an integrated low voltage switched-capacitor based power sensor, to measure the output power of a DC-DC boost converter. This approach results in a lower complexity, area, power consumption, and a lower component count for the overall PV MPPT system. Designed in a 180 nm CMOS process, the circuit can operate with a supply voltage of 1.8 V. It achieves a power sense accuracy of 7.6%, occupies a die area of 0.0519 mm2, and consumes 0.748 mW of power.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Dual-frequency single-inductor multiple-output (DF-SIMO) power converter topology for SoC applications

Modern mixed-signal SoCs integrate a large number of sub-systems in a single nanometer CMOS chip. Each sub-system typically requires its own independent and well-isolated power supply. However, to build these power supplies requires many large off-chip passive components, and thus the bill of material, the package pin count, and the printed circuit board area and complexity increase dramatically, leading to higher overall cost. Conventional (single-frequency) Single-Inductor Multiple-Output (SIMO) power converter topology can be employed to reduce the burden of off-chip inductors while producing a large number of outputs. However, this strategy requires even larger off-chip output capacitors than single-output converters due to time multiplexing between the multiple outputs, and thus many of them suffer from cross coupling issues that limit the isolation between the outputs. In this thesis, a Dual-Frequency SIMO (DF-SIMO) buck converter topology is proposed. Unlike conventional SIMO topologies, the DF-SIMO decouples the rate of power conversion at the input stage from the rate of power distribution at the output stage. Switching the input stage at low frequency (~2 MHz) simplifies its design in nanometer CMOS, especially with input voltages higher than 1.2 V, while switching the output stage at higher frequency enables faster output dynamic response, better cross-regulation, and smaller output capacitors without the efficiency and design complexity penalty of switching both the input and output stages at high frequency. Moreover, for output switching frequency higher than 100 MHz, the output capacitors can be small enough to be integrated on-chip. A 5-output 2-MHz/120-MHz design in 45-nm CMOS with 1.8-V input targeting low-power microcontrollers is presented as an application. The outputs vary from 0.6 to 1.6 V, with 4 outputs providing up to 15 mA and one output providing up to 50 mA. The design uses single 10-uH off-chip inductor, 2-nF on-chip capacitor for each 15-mA output and 4.5-nF for the 50-mA output. The peak efficiency is 73%, Dynamic Voltage Scaling (DVS) is 0.6 V/80 ns, and settling time is 30 ns for half-to-full load steps with no observable overshoot/undershoot or cross-coupling transients. The DF-SIMO topology enables realizing multiple efficient power supplies with faster dynamic response, better cross-regulation, and lower overall cost compared to conventional SIMO topologies

Multilevel multistate hybrid voltage regulator

In this work, a new set of voltage regulators as well as some controlling methods and schemes are proposed. While normal switched capacitor voltage regulators are easy integrable, they are suffering from charge sharing losses as well as fast degradation of efficiency when deviating from target operation point. On the other hand, conventional buck converters use bulky magnetic components that introduce challenges to integrate them on chip. The new set of voltage regulators covers the gap between inductor-based and capacitor-based voltage regulators by taking the advantages of both of them while avoiding or minimizing their disadvantages. The voltage regulator device consists of a switched capacitor circuit that is periodically switching its output between different voltage levels followed by a low pass filter to give a regulated output voltage. The voltage regulator is capable of converting an input voltage to a wide range of output voltage with a high efficiency that is roughly constant over the whole operation range. By switching between adjacent voltage levels, the voltage drop on the inductor is limited allowing for the use of smaller inductor sizes while maintaining the same performance. The general concept of the proposed voltage regulator as well as some operating conditions and techniques are explained. A phase interleaving technique to operate the multilevel multistate voltage regulator has been proposed. In this technique, the phases of two or more voltage levels are interleaved which enhances the effective switching frequency of the charge transferring components. This results in a further boost in the proposed regulator\u27s performance. A 4-level 4-state hybrid voltage regulator has been introduced as an application on the proposed concepts and techniques. It shows better performance compared to both integrated inductor-based and capacitor-based voltage regulators. The results prove that the proposed set of voltage regulators offers a potential move towards easing the integration of voltage regulators on chip with a performance that approaches that of off-chip voltage regulators

Digital Controlled Multi-phase Buck Converter with Accurate Voltage and Current Control

abstract: A 4-phase, quasi-current-mode hysteretic buck converter with digital frequency synchronization, online comparator offset-calibration and digital current sharing control is presented. The switching frequency of the hysteretic converter is digitally synchronized to the input clock reference with less than ±1.5% error in the switching frequency range of 3-9.5MHz. The online offset calibration cancels the input-referred offset of the hysteretic comparator and enables ±1.1% voltage regulation accuracy. Maximum current-sharing error of ±3.6% is achieved by a duty-cycle-calibrated delay line based PWM generator, without affecting the phase synchronization timing sequence. In light load conditions, individual converter phases can be disabled, and the final stage power converter output stage is segmented for high efficiency. The DC-DC converter achieves 93% peak efficiency for Vi = 2V and Vo = 1.6V.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

An Analysis of Non-Isolated DC-DC Converter Topologies with Energy Transfer Media

As miniaturized mobile devices with various functionalities are highly desired, the current requirement for loading blocks is gradually increasing. Accordingly, the efficiency of the power converter that supports the current to the loading bocks is a critical specification to prolong the battery time. Unfortunately, when using a small inductor for the miniaturization of mobile devices, the efficiency of the power converter is limited due to a large parasitic DC resistance (R-DCR) of the inductor. To achieve high power efficiency, this paper proposes an energy transfer media (ETM) that can make a switched inductor capacitor (SIC) converter easier to design, maintaining the advantages of both a conventional switched capacitor (SC) converter and a switched inductive (SI) converter. This paper shows various examples of SIC converters as buck, boost, and buck-boost topologies by simply cascading the ETM with conventional non-isolated converter topologies without requiring a sophisticated controller. The topologies with the ETM offer a major advantage compared to the conventional topologies by reducing the inductor current, resulting in low conduction loss dissipated at R-DCR. Additionally, the proposed topologies have a secondary benefit of a small output voltage ripple owing to the continuous current delivered to the load. Extensions to a multi-phase converter and single-inductor multiple-output converter are also discussed. Furthermore, a detailed theoretical analysis of the total conduction loss and the inductor current reduction is presented. Finally, the proposed topologies were simulated in PSIM, and the simulation results are discussed and compared with conventional non-isolated converter topologies

High Performance Power Management Integrated Circuits for Portable Devices

abstract: Portable devices often require multiple power management IC (PMIC) to power different sub-modules, Li-ion batteries are well suited for portable devices because of its small size, high energy density and long life cycle. Since Li-ion battery is the major power source for portable device, fast and high-efficiency battery charging solution has become a major requirement in portable device application. In the first part of dissertation, a high performance Li-ion switching battery charger is proposed. Cascaded two loop (CTL) control architecture is used for seamless CC-CV transition, time based technique is utilized to minimize controller area and power consumption. Time domain controller is implemented by using voltage controlled oscillator (VCO) and voltage controlled delay line (VCDL). Several efficiency improvement techniques such as segmented power-FET, quasi-zero voltage switching (QZVS) and switching frequency reduction are proposed. The proposed switching battery charger is able to provide maximum 2 A charging current and has an peak efficiency of 93.3%. By configure the charger as boost converter, the charger is able to provide maximum 1.5 A charging current while achieving 96.3% peak efficiency. The second part of dissertation presents a digital low dropout regulator (DLDO) for system on a chip (SoC) in portable devices application. The proposed DLDO achieve fast transient settling time, lower undershoot/overshoot and higher PSR performance compared to state of the art. By having a good PSR performance, the proposed DLDO is able to power mixed signal load. To achieve a fast load transient response, a load transient detector (LTD) enables boost mode operation of the digital PI controller. The boost mode operation achieves sub microsecond settling time, and reduces the settling time by 50% to 250 ns, undershoot/overshoot by 35% to 250 mV and 17% to 125 mV without compromising the system stability.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201