저전력, 저면적 유선 송수신기 설계를 위한 회로 기술

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 8. 정덕균.In this thesis, novel circuit techniques for low-power and area-efficient wireline transceiver, including a phase-locked loop (PLL) based on a two-stage ring oscillator, a scalable voltage-mode transmitter, and a forwarded-clock (FC) receiver based on a delay-locked-loop (DLL) based per-pin deskew, are proposed. At first, a two-stage ring PLL that provides a four-phase, high-speed clock for a quarter-rate TX in order to minimize power consumption is presented. Several analyses and verification techniques, ranging from the clocking architectures for a high-speed TX to oscillation failures in a two-stage ring oscillator, are addressed in this thesis. A tri-state-inverter–based frequency-divider and an AC-coupled clock-buffer are used for high-speed operations with minimal power and area overheads. The proposed PLL fabricated in the 65-nm CMOS technology occupies an active area of 0.009 mm2 with an integrated-RMS-jitter of 414 fs from 10 kHz to 100 MHz while consuming 7.6 mW from a 1.2-V supply at 10 GHz. The resulting figure-of-merit is -238.8 dB, which surpasses that of the state-of-the-art ring-PLLs by 4 dB. Secondly, a voltage-mode (VM) transmitter which offers a wide operation range of 6 to 32 Gb/s, controllable pre-emphasis equalization and output voltage swing without altering output impedance, and a power supply scalability is presented. A quarter-rate clocking architecture is employed in order to maximize the scalability and energy efficiency across the variety of operating conditions. A P-over-N VM driver is used for CMOS compatibility and wide voltage-swing range required for various I/O standards. Two supply regulators calibrate the output impedance of the VM driver across the wide swing and pre-emphasis range. A single phase-locked loop is used to provide a wide frequency range of 1.5-to-8 GHz. The prototype chip is fabricated in 65-nm CMOS technology and occupies active area of 0.48x0.36 mm2. The proposed transmitter achieves 250-to-600-mV single-ended swing and exhibits the energy efficiency of 2.10-to-2.93 pJ/bit across the data rate of 6-to-32 Gb/s. And last, this thesis describes a power and area-efficient FC receiver and includes an analysis of the jitter tolerance of the FC receiver. In the proposed design, jitter tolerance is maximized according to the analysis by employing a DLL-based de-skewing. A sample-swapping bang-bang phase-detector (SS-BBPD) eliminates the stuck locking caused by the finite delay range of the voltage-controlled delay line (VCDL), and also reduces the required delay range of the VCDL by half. The proposed FC receiver is fabricated in 65-nm CMOS technology and occupies an active area of 0.025 mm2. At a data rate of 12.5 Gb/s, the proposed FC receiver exhibits an energy efficiency of 0.36 pJ/bit, and tolerates 1.4-UIpp sinusoidal jitter of 300 MHz.Chapter 1. Introduction 1 1.1. Motivation 1 1.2. Thesis organization 5 Chapter 2. Phase-Locked Loop Based on Two-Stage Ring Oscillator 7 2.1. Overivew 7 2.2. Background and Analysis of a Two-stage Ring Oscillator 11 2.3. Circuit Implementation of The Proposed PLL 25 2.4. Measurement Results 33 Chapter 3. A Scalable Voltage-Mode Transmitter 37 3.1. Overview 37 3.2. Design Considerations on a Scalable Serial Link Transmitter 40 3.3. Circuit Implementation 46 3.4. Measurement Results 56 Chapter 4. Delay-Locked Loop Based Forwarded-Clock Receiver 62 4.1. Overview 62 4.2. Timing and Data Recovery in a Serial Link 65 4.3. DLL-Based Forwarded-Clock Receiver Characteristics 70 4.4. Circuit Implementation 79 4.5. Measurement Results 89 Chapter 5. Conclusion 94 Appendix 96 Appendix A. Design flow to optimize a high-speed ring oscillator 96 Appendix B. Reflection Issues in N-over-N Voltage-Mode Driver 99 Appendix C. Analysis on output swing and power consumption of the P-over-N voltage-mode driver 107 Appendix D. Loop Dynamics of DLL 112 Bibliography 121 Abstract 128Docto

A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

A 6.0-mW 10.0-Gb/s Receiver With Switched-Capacitor Summation DFE

A low-power receiver with a one-tap decision feedback equalization (DFE) was fabricated in 90-nm CMOS technology. The speculative equalization is performed using switched-capacitor-based addition at the front-end sample-hold circuit. In order to further reduce the power consumption, an analog multiplexer is used in the speculation technique implementation. A quarter-rate-clocking scheme facilitates the use of low-power front-end circuitry and CMOS clock buffers. The receiver was tested over channels with different levels of ISI. The signaling rate with BER<10^-12 was significantly increased with the use of DFE for short- to medium-distance PCB traces. At 10-Gb/s data rate, the receiver consumes less than 6.0 mW from a 1.0-V supply. This includes the power consumed in all quarter-rate clock buffers, but not the power of a clock recovery loop. The input clock phase and the DFE taps are adjusted externally

차세대 자동차용 카메라 데이터 통신을 위한 비대칭 동시 양방향 송수신기의 설계

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022.2. 정덕균.본 학위 논문에서는 차세대 자동차용 카메라 링크를 위해 높은 속도의 4레벨 펄스 진폭 변조 신호와 낮은 속도의 2레벨 펄스 진폭 변조 신호를 통신하는 비대칭 동시 양방향 송수신기의 설계 기술에 대해 제안하고 검증되었다. 첫번째 프로토타입 설계에서는, 10B6Q 직류 밸런스 코드를 탑재한 4레벨 펄스 진폭 변조 송신기와 고정된 데이터와 참조 레벨을 가지는 4레벨 펄스 진폭 변조 적응형 수신기에 대한 내용이 기술되었다. 4레벨 펄스 진폭 변조 송신기에서는 교류 연결 링크 시스템에 대응하기 위한 면적 및 전력 효율성이 좋은 10B6Q 코드가 제안되었다. 이 코드는 직류 밸런스를 맞추고 연속적으로 같은 심볼을 가지는 길이를 6개로 제한 시킨다. 비록 여기서는 입력 데이터 길이 10비트를 사용하였지만, 제안된 기술은 카메라의 다양한 데이터 타입에 대응할 수 있도록 입력 데이터 길이에 대한 확장성을 가진다. 반면, 4레벨 펄스 진폭 변조 적응형 수신기에서는, 샘플러의 옵셋을 최적으로 제거하여 더 낮은 비트에러율을 얻기 위해서, 기존의 데이터 및 참조 레벨을 조절하는 대신, 이 레벨들은 고정시키고 가변 게인 증폭기를 적응형으로 조절하도록 하였다. 상기 10B6Q 코드 및 고정 데이터 및 참조레벨 기술을 가진 프로토타입 칩들은 40 나노미터 상호보완형 메탈 산화 반도체 공정으로 제작되었고 칩 온 보드 형태로 평가되었다. 10B6Q 코드는 합성 게이트 숫자는 645개와 함께 단 0.0009 mm2 의 면적 만을 차지한다. 또한, 667 MHz 동작 주파수에서 단 0.23 mW 의 전력을 소모한다. 10B6Q 코드를 탑재한 송신기에서 8-Gb/s 4레벨 펄스 진폭 변조 신호를 고정 데이터 및 참조 레벨을 가지는 적응형 수신기로 12-m 케이블 (22-dB 채널 로스) 을 통해서 보낸 결과 최소 비트 에러율 108 을 달성하였고, 비트 에러율 105 에서는 아이 마진이 0.15 UI x 50 mV 보다 크게 측정되었다. 송수신기를 합친 전력 소모는 65.2 mW (PLL 제외) 이고, 성과의 대표수치는 0.37 pJ/b/dB 를 보여주었다. 첫번째 프로토타입 설계을 포함하여 개선된 두번째 프로토타입 설계에서는, 12-Gb/s 4레벨 펄스 진폭 변조 정방향 채널 신호와 125-Mb/s 2레벨 펄스 진폭 변조 역방향 채널 신호를 탑재한 비대칭 동시 양방향 송수신기에 대해 기술되고 검증되었다. 제안된 넓은 선형 범위를 가지는 하이브리드는 gmC 저대역 통과 필터와 에코 제거기와 함께 아웃바운드 신호를 24 dB 이상 효율적으로 감소시켰다. 또한, 넓은 선형 범위를 가지는 하이브리드와 함께 게인 감소기를 형성하게 되는 선형 범위 증폭기를 통해 4레벨 펄스 진폭 변조 신호의 선형성과 진폭의 트레이드 오프 관계를 깨는 것이 가능하였다. 동시 양방향 송수신기 칩은 40 나노미터 상호보완형 메탈 산화 반도체 공정으로 제작되었다. 상기 설계 기술들을 이용하여, 4레벨 펄스 진폭 변조 및 2레벨 펄스 진폭 변조 송수신기 모두 5m 채널 (채널 로스 15.9 dB) 에서 1E-12 보다 낮은 비트 에러율을 달성하였고, 총 78.4 mW 의 전력 소모를 기록하였다. 종합적인 송수신기는 성과 대표지표로 0.41 pJ/b/dB 와 함께 동시 양방향 통신 아래에서 4레벨 펄스 진폭 변조 신호 및 2레벨 펄스 진폭 변조 신호 각각에서 아이 마진 0.15 UI 와 0.57 UI 를 달성하였다. 이 수치는 성과 대표지표 0.5 이하를 가지는 기존 동시 양방향 송수신기와의 비교에서 최고의 아이 마진을 기록하였다.In this dissertation, design techniques of a highly asymmetric simultaneous bidirectional (SB) transceivers with high-speed PAM-4 and low-speed PAM-2 signals are proposed and demonstrated for the next-generation automotive camera link. In a first prototype design, a PAM-4 transmitter with 10B6Q DC balance code and a PAM-4 adaptive receiver with fixed data and threshold levels (dtLevs) are presented. In PAM-4 transmitter, an area- and power-efficient 10B6Q code for an AC coupled link system that guarantees DC balance and limited run length of six is proposed. Although the input data width of 10 bits is used here, the proposed scheme has an extensibility for the input data width to cover various data types of the camera. On the other hand, in the PAM-4 adaptive receiver, to optimally cancel the sampler offset for a lower BER, instead of adjusting dtLevs, the gain of a programmable gain amplifier is adjusted adaptively under fixed dtLevs. The prototype chips including above proposed 10B6Q code and fixed dtLevs are fabricated in 40-nm CMOS technology and tested in chip-on-board assembly. The 10B6Q code only occupies an active area of 0.0009 mm2 with a synthesized gate count of 645. It also consumes 0.23 mW at the operating clock frequency of 667 MHz. The transmitter with 10B6Q code delivers 8-Gb/s PAM-4 signal to the adaptive receiver using fixed dtLevs through a lossy 12-m cable (22-dB channel loss) with a BER of 1E-8, and the eye margin larger than 0.15 UI x 50 mV is measured for a BER of 1E-5. The proto-type chips consume 65.2 mW (excluding PLL), exhibiting an FoM of 0.37 pJ/b/dB. In a second prototype design advanced from the first prototypes, An asymmetric SB transceivers incorporating a 12-Gb/s PAM-4 forward channel and a 125-Mb/s PAM-2 back channel are presented and demonstrated. The proposed wide linear range (WLR) hybrid combined with a gmC low-pass filter and an echo canceller effectively suppresses the outbound signals by more than 24dB. In addition, linear range enhancer which forms a gain attenuator with WLR hybrid breaks the trade-off between the linearity and the amplitude of the PAM-4 signal. The SB transceiver chips are separately fabricated in 40-nm CMOS technology. Using above design techniques, both PAM-4 and PAM-2 SB transceivers achieve BER less than 1E-12 over a 5-m channel (15.9 dB channel loss), consuming 78.4 mW. The overall transceivers achieve an FoM of 0.41 pJ/b/dB and eye margin (at BER of 1E-12) of 0.15 UI and 0.57 UI for the forward PAM-4 and back PAM-2 signals, respectively, under SB communication. This is the best eye margin compared to the prior art SB transceivers with an FoM less than 0.5.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 DISSERTATION ORGANIZATION 4 CHAPTER 2 BACKGROUND ON AUTOMOTIVE CAMERA LINK 6 2.1 OVERVIEW 6 2.2 SYSTEM REQUIREMENTS 10 2.2.1 CHANNEL 10 2.2.2 POWER OVER DIFFERENTIAL LINE (PODL) 12 2.2.3 AC COUPLING AND DC BALANCE CODE 15 2.2.4 SIMULTANEOUS BIDIRECTIONAL COMMUNICATION 18 2.2.4.1 HYBRID 18 2.2.4.2 ECHO CANCELLER 20 2.2.5 ADAPTIVE RECEIVE EQUALIZATION 22 CHAPTER 3 AREA AND POWER EFFICIENT 10B6Q ENCODER FOR DC BALANCE 25 3.1 INTRODUCTION 25 3.2 PRIOR WORKS 28 3.3 PROPOSED AREA- AND POWER-EFFICIENT 10B6Q PAM-4 CODER 30 3.4 DESIGN OF THE 10B6Q CODE 33 3.4.1 PAM-4 DC BALANCE 35 3.4.2 PAM-4 TRANSITION DENSITY 35 3.4.3 10B6Q DECODER 37 3.5 IMPLEMENTATION AND MEASUREMENT RESULTS 40 CHAPTER 4 PAM-4 TRANSMITTER AND ADAPTIVE RECEIVER WITH FIXED DATA AND THRESHOLD LEVELS 45 4.1 INTRODUCTION 45 4.2 PRIOR WORKS 47 4.3 ARCHITECTURE AND IMPLEMENTATION 49 4.2.1 PAM-4 TRANSMITTER 49 4.2.2 PAM-4 ADAPTIVE RECEIVER 52 4.3 MEASUREMENT RESULTS 62 CHAPTER 5 ASYMMETRIC SIMULTANEOUS BIDIRECTIONAL TRANSCEIVERS USING WIDE LINEAR RANGE HYBRID 68 5.1 INTRODUCTION 68 5.2 PRIOR WORKS 70 5.3 WIDE LINEAR RANGE (WLR) HYBRID 75 5.3 IMPLEMENTATION 78 5.3.1 SERIALIZER (SER) DESIGN 78 5.3.2 DESERIALIZER (DES) DESIGN 79 5.4 HALF CIRCUIT ANALYSIS OF WLR HYBRID AND LRE 82 5.5 MEASUREMENT RESULTS 88 CHAPTER 6 CONCLUSION 97 BIBLIOGRAPHY 99 초 록 106박

State of the art in chip-to-chip interconnects

This thesis presents a study of short-range links for chips mounted in the same package, on printed circuit boards or interposers. Implemented in CMOS technology between 7 and 250 nm, with links that operate at a data rate between 0,4 and 112 Gb/s/pin and with energy efficiencies from 0,3 to 67,7 pJ/bit. The links operate on channels with an attenuation lower than 50 dB. A comparison is made with graphical representations between the different articles that shows the correlation between the different essential metrics of chip-to-chip interconnects, as well as its evolution over the last 20 years.Esta tesis presenta un estudio de enlaces de corto alcance para chips montados en un mismo paquete, en placas de circuito impreso o intercaladores. Implementado en tecnología CMOS entre 7 y 250 nm, con enlaces que operan a una velocidad de datos entre 0,4 y 112 Gb/s/pin y con eficiencias energéticas de 0,3 a 67,7 pJ/bit. Los enlaces operan en canales con una atenuación inferior a 50 dB. Se realiza una comparación con representaciones gráficas entre los diferentes artículos que muestra la correlación entre las distintas métricas esenciales de las interconexiones chip a chip, así como su evolución en los últimos 20 años.Aquesta tesi presenta un estudi d'enllaços de curt abast per a xips muntats en el mateix paquet, en plaques de circuits impresos o interposers. Implementat en tecnologia CMOS entre 7 i 250 nm, amb enllaços que funcionen a una velocitat de dades entre 0,4 i 112 Gb/s/pin i amb eficiències energètiques de 0,3 a 67,7 pJ/bit. Els enllaços funcionen en canals amb una atenuació inferior a 50 dB. Es fa una comparació amb representacions gràfiques entre els diferents articles que mostra la correlació entre les diferents mètriques essencials d'interconnexions xip a xip, així com la seva evolució en els darrers 20 anys

대역폭 증대 기술을 이용한 전력 효율적 고속 송신 시스템 설계

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022.2. 정덕균.The high-speed interconnect at the datacenter is being more crucial as 400 Gb Ethernet standards are developed. At the high data rate, channel loss re-quires bandwidth extension techniques for transmitters, even for short-reach channels. On the other hand, as the importance of east-to-west connection is rising, the data center architectures are switching to spine-leaf from traditional ones. In this trend, the number of short-reach optical interconnect is expected to be dominant. The vertical-cavity surface-emitting laser (VCSEL) is a com-monly used optical modulator for short-reach interconnect. However, since VCSEL has low bandwidth and nonlinearity, the optical transmitter also needs bandwidth-increasing techniques. Additionally, the power consumption of data centers reaches a point of concern to affect climate change. Therefore, this the-sis focuses on high-speed, power-efficient transmitters for data center applica-tions. Before the presenting circuit design, bandwidth extension techniques such as fractionally-spaced feed-forward equalizer (FFE), on-chip transmission line, inductive peaking, and T-coil are mathematically analyzed for their effec-tiveness. For the first chip, a power and area-efficient pulse-amplitude modulation 4 (PAM-4) transmitter using 3-tap FFE based on a slow-wave transmission line is presented. A passive delay line is adopted for generating an equalizer tap to overcome the high clocking power consumption. The transmission line achieves a high slow-wave factor of 15 with double floating metal shields around the differential coplanar waveguide. The transmitter includes 4:1 multi-plexers (MUXs) and a quadrature clock generator for high-speed data genera-tion in a quarter-rate system. The 4:1 MUX utilizes a 2-UI pulse generator, and the input configuration is determined by qualitative analysis. The chip is fabri-cated in 65 nm CMOS technology and occupies an area of 0.151 mm2. The proposed transmitter system exhibits an energy efficiency of 3.03 pJ/b at the data rate of 48 Gb/s with PAM-4 signaling. The second chip presents a power-efficient PAM-4 VCSEL transmitter using 3-tap FFE and negative-k T-coil. The phase interpolators (PIs) generate frac-tionally-spaced FFE tap and correct quadrature phase error. The PAM-4 com-bining 8:1 MUX is proposed rather than combining at output driver with double 4:1 MUXs to reduce serializing power consumption. T-coils at the internal and output node increase the bandwidth and remove inter-symbol interference (ISI). The negative-k T-coil at the output network increases the bandwidth 1.61 times than without T-coil. The VCSEL driver is placed on the high VSS domain for anode driving and power reduction. The chip is fabricated in 40 nm CMOS technology. The proposed VCSEL transmitter operates up to 48 Gb/s NRZ and 64 Gb/s PAM-4 with the power efficiency of 3.03 pJ/b and 2.09 pJ/b, respec-tively.400Gb 이더넷 표준이 개발됨에 따라 데이터 센터의 고속 상호 연결이 더욱 중요해지고 있다. 높은 데이터 속도에서의 채널 손실에 의해 단거리 채널의 경우에도 송신기에 대한 대역폭 확장 기술이 필요하다. 한편, 데이터 센터 내 동-서 연결의 중요성이 높아지면서 데이터 센터 아키텍처가 기존의 아키텍처에서 스파인-리프로 전환되고 있다. 이러한 추세에서 단거리 광학 인터커넥트의 수가 점차 우세해질 것으로 예상된다. 수직 캐비티 표면 방출 레이저(VCSEL)는 일반적으로 단거리 상호 연결을 위해 사용되는 광학 모듈레이터이다. VCSEL은 낮은 대역폭과 비선형성을 가지고 있기 때문에, 광 송신기도 대역폭 증가 기술을 필요로 한다. 또한, 데이터 센터의 전력 소비는 기후 변화에 영향을 미칠 수 있는 우려 지점에 도달했다. 따라서, 본 논문은 데이터 센터 응용을 위한 고속 전력 효율적인 송신기에 초점을 맞추고 있다. 회로 설계를 제시하기 전에, 부분 간격 피드-포워드 이퀄라이저 (FFE), 온칩 전송선로, 인덕터, T-코일과 같은 대역폭 확장 기술을 수학적으로 분석한다. 첫 번째 칩은 저속파 전송선로를 기반으로 한 3-탭 FFE를 사용하는 전력 및 면적 효율적인 펄스-진폭-변조 4(PAM-4) 송신기를 제시한다. 높은 클럭 전력 소비를 극복하기 위해 이퀄라이저 탭 생성을 위해 수동소자 지연 라인을 채택했다. 전송 라인은 차동 동일평면도파관 주위에 이중 플로팅 금속 차폐를 사용하여 15의 높은 전달속도 감쇠를 달성한다. 송신기에는 4:1 멀티플렉서(MUX)와 4-위상 클럭 생성기가 포함되어 있다. 4:1 MUX는 2-UI 펄스 발생기를 사용하며, 정성 분석에 의해 입력 구성이 결정된다. 이 칩은 65 nm CMOS 기술로 제작되었으며 0.151 mm2의 면적을 차지한다. 제안된 송신기 시스템은 PAM-4 신호와 함께 48 Gb/s의 데이터 속도에서 3.03 pJ/b의 에너지 효율을 보여준다. 두 번째 칩에서는 3-탭 FFE 및 역회전 T-코일을 사용하는 전력 효율적인 PAM-4 VCSEL 송신기를 제시한다. 위상 보간기(PI)는 부분 간격 FFE 탭을 생성하고 4-위상 클럭 오류를 수정하는 데 사용된다. 직렬화 전력 소비를 줄이기 위해 출력 드라이버에서 MSB와 LSB를 두 개의 4:1 MUX를 통해 결합하는 대신 8:1 MUX를 통해 PAM-4로 결합하는 회로가 제안된다. 내부 및 출력 노드에서 T-코일은 대역폭을 증가시키고 기호 간 간섭(ISI)을 제거한다. 출력 네트워크에서 역회전 T-코일은 T-코일이 없는 경우보다 대역폭을 1.61배 증가시킨다. VCSEL 드라이버는 양극 구동 및 전력 감소를 위해 높은 VSS 도메인에 배치된다. 이 칩은 40 nm CMOS 기술로 제작되었다. 제안된 VCSEL 송신기는 각각 3.03pJ/b와 2.09pJ/b의 전력 효율로 최대 48Gb/s NRZ와 64Gb/s PAM-4까지 작동한다.ABSTRACT I CONTENTS III LIST OF FIGURES V LIST OF TABLES IX CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 BACKGROUND OF HIGH-SPEED INTERFACE 6 2.1 OVERVIEW 6 2.2 BASIS OF DATA CENTER ARCHITECTURE 9 2.3 SHORT-REACH INTERFACE STANDARDS 12 2.4 ANALYSES OF BANDWIDTH EXTENSION TECHNIQUES 16 2.4.1 FRACTIONALLY-SPACED FFE 16 2.4.2 TRANSMISSION LINE 21 2.4.3 INDUCTOR 24 2.4.4 T-COIL 33 CHAPTER 3 DESIGN OF 48 GB/S PAM-4 ELECTRICAL TRANSMITTER IN 65 NM CMOS 43 3.1 OVERVIEW 43 3.2 FFE BASED ON DOUBLE-SHIELDED COPLANAR WAVEGUIDE 46 3.2.1 BASIC CONCEPT 46 3.2.2 PROPOSED DOUBLE-SHIELDED COPLANAR WAVEGUIDE 47 3.3 DESIGN CONSIDERATION ON 4:1 MUX 50 3.4 PROPOSED PAM-4 ELECTRICAL TRANSMITTER 53 3.5 MEASUREMENT 57 CHAPTER 4 DESIGN OF 64 GB/S PAM-4 OPTICAL TRANSMITTER IN 40 NM CMOS 64 4.1 OVERVIEW 64 4.2 DESIGN CONSIDERATION OF OPTICAL TRANSMITTER 66 4.3 PROPOSED PAM-4 VCSEL TRANSMITTER 69 4.4 MEASUREMENT 82 CHAPTER 5 CONCLUSIONS 88 BIBLIOGRAPHY 90 초 록 101박

Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications

High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator

A 60-Gb/s PAM4 Wireline Receiver With 2-Tap Direct Decision Feedback Equalization Employing Track-and-Regenerate Slicers in 28-nm CMOS

This article describes a 4-level pulse amplitude modulation (PAM4) receiver incorporating continuous time linear equalizers (CTLEs) and a 2-tap direct decision feedback equalizer (DFE) for applications in wireline communication. A CMOS track-and-regenerate slicer is proposed and employed in the PAM4 receiver. The proposed slicer is designed for the purposes of improving the clock-to-Q delay as well as the output signal swing. A direct DFE in a PAM4 receiver is made possible with the proposed slicer by having rail-to-rail digital feedback signals available with reduced delay, and accordingly relaxing the settling time constraint of the summer. With the 2-tap direct DFE enabled by the proposed slicer, loop-unrolling and inductor-based bandwidth enhancement techniques, which can be area/power intensive, are not necessary at high data rates. The PAM4 receiver fabricated in 28-nm CMOS technology achieves bit-error-rate (BER) better than 1E-12, and energy efficiency of 1.1 pJ/b at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist