Data Management Study, Volume 5. Appendix H - Contractor Data Package Logistics and Support /LS/ Final Report

Contractor data package for Voyager logistics and support in transportation, communications, supply, and maintenanc

Data management study, volume 5. Appendix F - Contractor data package test /TE/ and mission operations /MP/ Final report

Test and mission operations contractor data package for Voyager spacecraf

The Mechanical Performance of Subscale Candidate Elastomer Docking Seals

The National Aeronautics and Space Administration is developing a Low Impact Docking System (LIDS) for future exploration missions. The mechanism is a new state-of-the-art device for in-space assembly of structures and rendezvous of vehicles. At the interface between two pressurized modules, each with a version of the LIDS attached, a composite elastomer-metal seal assembly prevents the breathable air from escaping into the vacuum of space. Attached to the active LIDS, this seal mates against the passive LIDS during docking operation. The main interface seal assembly must exhibit low leak and outgas values, must be able to withstand various harsh space environments, must remain operational over a range of temperatures from -50 C to 75 C, and perform after numerous docking cycles. This paper presents results from a comprehensive study of the mechanical performance of four candidate subscale seal assembly designs at -50, 23, 50, and 75 C test temperatures. In particular, the force required to fully compress the seal during docking, and that which is required for separation during the undocking operation were measured. The height of subscale main interface seal bulbs, as well as the test temperature, were shown to have a significant effect on the forces the main interface seal of the LIDS may experience during docking and undocking operations. The average force values required to fully compress each of the seal assemblies were shown to increase with test temperature by approximately 50% from -50 to 75 C. Also, the required compression forces were shown to increase as the height of the seal bulb was increased. The seal design with the tallest elastomer seal bulb, which was 31% taller than that with the shortest bulb, required force values approximately 45% higher than those for the shortest bulb, independent of the test temperature. The force required to separate the seal was shown to increase with decreasing temperature after 15 hours of simulated docking. No adhesion force was observed at 75 C, while magnitudes of up to 235 lbf were recorded at the refrigerated temperature. In addition, the adhesion force was observed to increase with bulb height. When compared with the LIDS program requirements, the measured compression force values were found to be below the maximum allowable load allotted to the main interface seal. However, the measured adhesion force values at the refrigerated test temperature were found to exceed the program limits

Shear-driven size segregation of granular materials: modeling and experiment

Granular materials segregate by size under shear, and the ability to quantitatively predict the time required to achieve complete segregation is a key test of our understanding of the segregation process. In this paper, we apply the Gray-Thornton model of segregation (developed for linear shear profiles) to a granular flow with an exponential profile, and evaluate its ability to describe the observed segregation dynamics. Our experiment is conducted in an annular Couette cell with a moving lower boundary. The granular material is initially prepared in an unstable configuration with a layer of small particles above a layer of large particles. Under shear, the sample mixes and then re-segregates so that the large particles are located in the top half of the system in the final state. During this segregation process, we measure the velocity profile and use the resulting exponential fit as input parameters to the model. To make a direct comparison between the continuum model and the observed segregation dynamics, we locally map the measured height of the experimental sample (which indicates the degree of segregation) to the local packing density. We observe that the model successfully captures the presence of a fast mixing process and relatively slower re-segregation process, but the model predicts a finite re-segregation time, while in the experiment re-segregation occurs only exponentially in time

Data management study, volume 5. Appendix A - Contractor data package technical description and system engineering /SE/ Final report

Technical description and systems engineering contractor data package for Voyager spacecraf

Stoichiometry control of sputtered CuCl thin films: Influence on ultraviolet emission properties

We demonstrate that the chemical composition of the sputtered CuCl thin films could be finely controlled by adjusting the bias to the substrate. The films deposited without any intentional bias were Cl rich (CuCl1+x), a bias of −22 V yielded stoichiometric CuCl, and a further increase in the negative bias resulted in Cl deficient films (CuCl1−x). The crystalline and optical properties were found to be associated with the chemical composition. Cl rich films showed a deep level green emission at around 515 nm in addition to ultraviolet (UV) excitonic emission. The stoichiometric films have higher optical quality, exhibiting a sharp UV emission at around 385 nm at room temperature, compared to nonstoichiometric samples. Visible luminescence related to deep level defects was not observed in the stoichiometric films. Changes in energy of the flux from the target and the subsequent ion bombardment on the substrate surface are correlated with the variations in chemical composition and their impact on the film microstructure and UV emission

Segregation by thermal diffusion in granular shear flows

Segregation by thermal diffusion of an intruder immersed in a sheared granular gas is analyzed from the (inelastic) Boltzmann equation. Segregation is induced by the presence of a temperature gradient orthogonal to the shear flow plane and parallel to gravity. We show that, like in analogous systems without shear, the segregation criterion yields a transition between upwards segregation and downwards segregation. The form of the phase diagrams is illustrated in detail showing that they depend sensitively on the value of gravity relative to the thermal gradient. Two specific situations are considered: i) absence of gravity, and ii) homogeneous temperature. We find that both mechanisms (upwards and downwards segregation) are stronger and more clearly separated when compared with segregation criteria in systems without shear.Comment: 8 figures. To appear in J. Stat. Mec

Plataforma de telhas de fibrocimento: estrutura hidropônica para a produção de batata-semente pré-básica.

bitstream/item/31541/1/comunicado58.pd