This paper describes a proven technique that maximizes either the hydraulic impact force or the hydraulic power of the fluid hitting the bottom of the hole. The objective is to determine nozzle sizes and flow rate to deliver maximum Hydraulic Horse power (HHP) or Jet Impact Force (JIF) within specified operating constraints

Richard Lado Longwa Milla, Richard Lado

English

This report gives the account on the dissertation of the final year project report title

"Optimization of Drilling Hydraulics in Vertical Hole" assigned to the student as one of

the courses requirement by the Universiti Teknologi PETRONAS before his graduation.

The final year project given for period of two semesters starting from January of the first

semester and ends December of the second semester 2008. Immediately following the

continuation of the FYP I on this project, the student carries on to do study on the

project. In the following dissertation report, it reports on the work that has been

accomplished.

The necessary conditions for attaining optimal bottom hole cleaning below a drill bit is

usually approximated via the optimization of two design criteria: Hydraulic Impact force

and Bit Hydraulic horsepower. The process involves running a circulating pressure test

at the rig site, while keeping the rotary speed and weight-on-bit constant. The test

involves varying the mud pump speed and recording the pump pressure and circulating

rate at each speed.

This paper describes a proven technique that maximizes either the hydraulic impact

force or the hydraulic power of the fluid hitting the bottom of the hole. The objective is

to determine nozzle sizes and flow rate to deliver maximum Hydraulic Horse power

(HHP) or Jet Impact Force (JIF) within specified operating constraints.

In this paper, the introductory part in chapter one talked about the background, problem

statement, Objective and the scope of study. Second chapter covers the literature review

on the study and chapter three the methodology used. Chapter four discusses on the

finding of the study, chapter five discusses the results and final chapter six gives the

conclusion and the recommendation

Longwa Milia, Richard Lado

UTPedia

OPTIMIZATION OF. DRILLING HYDRAULICS IN VERTICAL HOLES

                                                                            i   OPTIMIZATION OF DRILLING HYDRAULICS IN VERTICAL HOLES   BY:  Richard Lado Longwa Milla         7139    Dissertation submitted in partial fulfillment of the requirements for the  Bachelor of Engineering (Hons)  (Mechanical Engineering)   July 2008        Universiti Teknologi PETRONAS Bandar Seri Iskandar 31750 Tronoh Perak Darul Ridzuan                                                                               ii  CERTIFICATION OF APPROVAL   Optimization of drilling hydraulics in vertical holes   By   Richard Lado Longwa Milla   7139  A project dissertation submitted to the Mechanical Engineering Programme Universiti Teknologi PETRONAS In partial fulfillment of the requirement for the BACHELOR OF ENGINEERING (Hons)  (CHEMICAL ENGINEERING)        Approved by,   …………………………………….. Mr Elias B. Abllah       UNIVERSITI TEKNOLOGI PETRONAS  TRONOH, PERAK  July 2008                                                                                iii  CERTIFICATION OF ORIGINALITY   This is to certify that the writer is responsible for the work submitted in this project, that the original work is his own except as specified in the references and acknowledgements, and that the original work contained herein have not been undertaken or done by unspecified sources or persons.     _______________________ Richard Lado Longwa Milla                                                                                                   iv  ABSTRACT  This report gives the account on the dissertation of the final year project report title “Optimization of Drilling Hydraulics in Vertical Hole” assigned to the student as one of the courses requirement by the Universiti Teknologi PETRONAS before his graduation.  The final year project given for period of two semesters starting from January of the first semester and ends December of the second semester 2008.  Immediately following the continuation of the FYP 1 on this project, the student carries on to do study on the project. In the following dissertation report, it reports on the work that has been accomplished. The necessary conditions for attaining optimal bottom hole cleaning below a drill bit is usually approximated via the optimization of two design criteria: Hydraulic Impact force and Bit Hydraulic horsepower. The process involves running a circulating pressure test at the rig site, while keeping the rotary speed and weight-on-bit constant. The test involves varying the mud pump speed and recording the pump pressure and circulating rate at each speed.  This paper describes a proven technique that maximizes either the hydraulic impact force or the hydraulic power of the fluid hitting the bottom of the hole. The objective is to determine nozzle sizes and flow rate to deliver maximum Hydraulic Horse power (HHP) or Jet Impact Force (JIF) within specified operating constraints. In this paper, the introductory part in chapter one talked about the background, problem statement, Objective and the scope of study.  Second chapter covers the literature review on the study and chapter three the methodology used.  Chapter four discusses on the finding of the study, chapter five discusses the results and final chapter six gives the conclusion and the recommendation.                                                                                 v    ACKNOWLEDGEMENT  First and for most, the Author would like to thank God the Almighty for the guidance He has bestowed to him all the time.  His gratitude also goes to his supervisors, whom without their helps and guidance, the project would have not been a success.  Mr.: Elias B. Abllah  And my co-supervisor Dr: Sony Irwan.  He would like to thank his supervisor, co-supervisor and others who rendered him their guidance and support that have inspired him to do his best to obtain this project. He would like also to thank the Petrodar Operating Company - Sudan for their support for the project, he would like everyone to know that this project succeeded because of everyone positive contribution which he very much appreciate indefinitely. The author also would like to thank the University laboratory technicians for their help during the experiments. The author would like to thank all his class mates for their supports directly or indirectly for the successes of this project. Last but not the least, the author would like to take this opportunity to give his special thanks to his mother, brothers and sisters and all other members of the family for their constants support throughout the duration of this project. He would like them to know that their continues support is the key to his success and aspiration for the future. Lastly, He would like to say his cordial  regards and gratitude to all those whom he failed to mentioned, that he would always remain grateful for your assistance and supports. Thank you so much and may God keep you and support you always.                                                                               vi   TABLE OF CONTENTS   CERTIFICATION . . . . .          .           iii  ABSTRACT . . . . . . . . iv  ACKNOWLEDGEMENT . . . . . . v  CHAPTER 1: INTRODUCTION . . . . 1     1.1  Background of Study . . . 1     1.2 Problem Statement . . . 3     1.3 Objectives                   .           .           .           4                                               1.4       Scope of Study . .           .           4      CHAPTER 2: LITERATURE REVIEW . . . 6     2.1 Drilling Hydraulic and Cutting Transport 6  CHAPTER 3: METHODOLOGY . . . . 8     3.1 Procedure identification . . 8      CHAPTER 4:  DISCUSSION ON THE STUDY . . 9      4.1 Hydrostatic Pressure inside the Wellbore 9     4.2 Types of Fluid Flow . . .           11                                     4.3       Rheological Classification of Fluids   .          13                                     4.4         Laminar Flow in Pipes and Annuli   .          14                                     4.5       Turbulent Flow in Pipes and Annuli  .           14                                     4.6       Pressure Drop across Surface Connections    15                                     4.7       Pressure Drop across Bit                                16                                     4.8       Initiating Circulation   .           .          .           17                                     4.9       Optimization of Bit Hydraulics          .           17                                     4.10     Limiting Conditions for                                                  Both Optimization Criteria      .          .           19                                     4.11     Measuring “m”             .           .          .           20                                     4.12     Hydraulic Optimization for                                                 the Power Limited Case.          .          .           21                                     4.13     Hydraulic Horse Power (HHP).          .           22                                     4.14     Jet Impact Force (JIF)  .           .          .           22  CHAPTER 5: RESULTS AND DISCUSSION         .          .          24     5.1 Graphical Method for Optimization                                                   of Hydraulics Program Conclusion  .  26     5.2 An Empirical Relationship between                                                   P and Q in Turbulent flow gives.  .           26                                                                              vii   CHAPTER 6:            CONCLUSION AND RECOMMANDATION      38                                     6.1        Conclusion.           .           .           .           .     38                                     6.2        Recommendations           .           .             .     38    REFERENCES . . . . . . .           . 40                                                                                     viii  APPENDIX 6-9 LIST OF FIGURES    Figure 1.1 HHP & JIF at the bit and the bottom hole assembly parameter.................2 Figure 1.2 Bit body balling..........................................................................................3 3.1 Flowchart on methodology research.......................................................................8 Figure 4.1 viscometer (Source: UTP drilling Fluid lab)..............................................14 Figure 4.2 Hydraulics Optimization Circulation system..............................................19 Figure 5.1 Limited conditions......................................................................................24 Figure 5.2     Pressure at the bit verses nozzle area percentage deviation………….…..35 Figure 5.3    HHP at the bit verses the Nozzle area percentage deviation………...……35 Figure 5.4    JIT at the bit verses Nozzle area percentages deviation…………..………36 Figure 5.5   Tthe bit and the surface pressure loss verses  nozzle area percenteg deviation.......................................................................................36 Figure 5.6 Nozzle velocity verses nozzle area percentage deviation…………………...37  LIST OF TABLES Table 4.1.      Group of surface Equipment……………………………………………..15 Table 4.2. Equivalent drillpipe lengths for surface equipment…………………………15 Table 5.1. circulating system factor................................................................................28 Table 5.2. Nozzle area and sizes......................................................................................29 Table 5.3  Pump’s rate vs. equivalent surface pressure...................................................30 Table 5.4   Pump’s type and specification.......................................................................30 Table 5.5 The desired annulus velocity for the operation................................................32 Table 5.6   Pump’s rates and the corresponding system pressures..................................32 Table 5.7   System flow rate and the corresponding Bit pressure (0.45 in2)....................33 Table 5.8 Flow rate, system, bit and circulation pressures..............................................33 Table 5.9 Nozzle deviation vs. Hydraulic optimization parameters................................34      

Optimization of drilling hydraulics in vertical holes

http://utpedia.utp.edu.my/10004/1/2008%20-%20Optimization%20of%20Drilling%20Hydraulics%20in%20Vertical%20Holes.pdf

Optimization of drilling hydraulics in vertical holes

Abstract

Similar works

Full text

Available Versions

UTPedia

UTPedia