This paper presents a study of the development of a surface roughness model in end milling of hardened

steel AISI D2 using PVD TiAIN coated carbide cutting tool. The hardness of AISI D2 tool lies within the

range of 56-58 HRe. The independent variables or the primary machining parameters selected for this experiment were the cutting speed, feed, and depth of cut. First and second order models were developed using Response Surface Methodology (RSM). Experiments were conducted within specified ranges of the parameters. Design-Expert 6.0 software was used to develop the surface roughness equations as the predictive models. Analysis of variance (ANOVA) with 95% confidence interval has indicated that the

models are valid in predicting the surface roughness of the part machined under specified condition

Amin, A. K. M. Nurul

Hafiz, A.M. Khalid

Karim, A.N. Mustafizul

Lajis, M. A.

English

The International Islamic University Malaysia Repository

[108JPrediction of Surface Roughness in Hard Milling of AISI D2 Tool SteelM.A. LAJIS', A.N. Mustafizul KARIM2, AKM. Nurul AMIN2, A.M.K. HAFIZ2'Faculty of Mechanical and Manufacturing Engineering, UTHM, Malaysia, amri@uthm.edu.my2Department of Manufacturing and Material Engineering, HUM, Malaysia, mustafizul@iiu.edu.rriyAbstract:This paper presents a study of the development of a surface roughness model in end milling of hardenedsteel AISI D2 using PVD TiAIN coated carbide cutting tool. The hardness of AISI D2 tool lies within therange of 56-58 HRe. The independent variables or the primary machining parameters selected for thisexperiment were the cutting speed, feed, and depth of cut. First and second order models were developedusing Response Surface Methodology (RSM). Experiments were conducted within specified ranges of theparameters. Design-Expert 6.0 software was used to develop the surface roughness equations as thepredictive models. Analysis of variance (ANOVA) with 95% confidence interval has indicated that themodels are valid in predicting the surface roughness of the part machined under specified condition.Keywords: Surface roughness, Response surface methodology, Hard milling, Coated carbide1. IntroductionSurface roughness is widely used as an indicator forproduct quality. This is a very important criterionconcerning mold and die making. Machining hardmaterial used for die and mold commonly results in hightool wear with less material removal rate. Securing thehigh quality of surface finish of the die materialfollowed by machining at high metal removal rate is agreat challenge for the manufacturers. High metalremoval rate is intended to reduce the manufacturingcosts and operation time. But despite having the target ofachieving optimum superficial finishing with theshortest possible time one must take into account theconsideration of tool life, so that the complete finishingoperation can be carried out with just one tool, avoidingthe intermediate stops in order to change the tool due toits wear [1].There are various methodologies and strategies thatwere adopted by researchers in order to predict surfaceroughness in milling and turning. Four major categorieswere created to classify the methodologies. These are: (i)approaches that are based on machining theory todevelop analytical models and/or computer algorithms torepresent the machined surface; (ii) approaches thatexamine the effects of various factors through theexecution of experiments and analysis of the results; (iii)approaches that use designed experiments; and (iv) theartificial intelligence (AI) approaches [2].Response surface methodology (RSM) which isclassified into designed experiments approach seems tobe the most wide-spread methodology for the surfaceroughness prediction. RSM is an important methodologyused in developing new processes, optimizing theirperformance, and improving the design and/orformulation of new products. It is often an importantconcurrent engineering tool in which product design,process development, quality, manufacturingengineering, and operations personnel often worktogether in a team environment to apply RSM [3]. It is adynamic and foremost important tool of design ofexperiment (DOE), wherein the relationship betweenresponses of a process with its input decision variables ismapped to achieve the objective of maximization orminimization of the response properties.Many researchers have used RSM for theirexperimental design and analysis of the results in endmilling [4-8], but very few of them were engaged inmachining hard material which is commonly known ashard milling. J. Vivancos et. al. [9] presented a modelfor the prediction of surface roughness in high-speedside milling of hardened die steels. He identified thefactors and interactions that are statistically moresignificant for modelling the surface roughness (R.). Thedevelopment of a surface roughness model for endmilling EN32 casehardening carbon steel (160 BRNsteel) using design of experiments and RSM wasdiscussed by A. Mansor et al [10].In this paper, the RSM has been applied to develop amathematical model to predict the surface roughness forend milling of hardened steel AISI D2 tool steel which iscategorized as a difficult to cut material. Machining wasconducted using PVD TiAlN carbide coated SANDVIK1030 inserts. The predicted surface roughness resultsare presented in terms of both l" and 2nd order equationswith the aid of a statistical design of experimentsoftware called Design-Expert version 6.0.2. Mathematical model by RSMThe relationship between surface roughness and otherindependent variables is modelled as follows:(1)where 'C' is a model constant and k, I and m are modelparameters. The above function (1) can be represented inlinear mathematical form as follows:IuRa = In C + k In V + Zln d +m In! (2)-47-The first-order linear model of the above Eq. (2) canbe represented as follows:.h = Y-E: = boxo +b1xI +b2x2 +b3x3 (3)where, Y I is the estimated response based on first-order equation and y is the measured surface roughnesson a logarithmic scale, Xo = 1 (dummy variable), X1, X2,X3 are logarithmic transformations of speed, depth of cutand feed respectively. The parameters bo, b: b2, and b,are to be estimated where € the experimental error. Thesecond-order model can be extended from the first-orderequation as follows:Y2 =Y - E:=. boxo+ b.x, + b2x2 + b3X3 + bl1X~+ b22X;+b33X; +b12x1X2 + b13x1X3 +b23X2X3(4)where Y2 is the estimated response based on thesecond-order model. Analysis of variance (ANOVA) isused to verify and validate the model.3. Experimental design and methodologyExperimental works were carried out on CNCVertical Milling Center (VMC) Excell PMC-lOT24with 40 mm diameter tool holder. End milling operationwas performed under dry cutting conditions with a 5 mmconstant radial depth of cut. Down milling method wasemployed to secure the advantageous outcomes such asbetter surface finish, less heat generation, larger tool life,better geometrical accuracy and compressive stressesfavorable for carbide edges [11]. In this experiment onlyone insert was used for each set of experimentalconditions so that the variation due to the wear of cuttingtool edge is minimized among the trials, leaving noscope of ambiguity due to the effect in variation ofcutting tool geometry. Surface roughness was measuredby Mitutoyo SURFTEST SV-500 with cut-offlength 0.8mm and sampling length 4.0 mm.The cutting conditions were selected by consideringthe recommendations of the cutting tool's manufacturer(Sandvik Tools) and the knowledge of practices,gathered through contemporary literatures on hardmachining. Few trial runs were, however, conducted toaugment the selection of parameters. The tool life andthe material removal rate were actively consideredwithout limiting the choice oriented to the hardness ofthe material to be studied. The hardness of AISI D2 steelused for these experiments was measured usingHardness Rockwell tester and the values were found tobe between 56-58 HRC. The three main selectedparameters: cutting speed, depth of cut and feed werethen coded to the levels using the followingtransformations:.X, = (In V = ln 56.57)/(ln 72.28 -In 56.57),X2 = (In d -In 1.00)/(ln 1.63 -In 1.00), andX3 = (In F -In 0.044)/(ln 0.079 -In 0.044) (5)The independent variables with their correspondingselected levels of variation and coding identification arepresented in Table 1.Table 1: Independent variables with levels and codingid tifi atioen IC nLevels in Coded FormIndependentVariables->/2 -1 0 +1 +>/2(lowest) (low) (centre) (high) (highest)Cuttingspeed (V) 40 44.27 56.57 72.28 80(rn/min)(XI!Depth of cut(d) 0.50 0.61 1.00 1.63 2.00(rnrn)(X2)Feed (F)0.10(rnrn!tooth) 0.02 0.025 0.044 0.079(X3)A well-planned design of experiment cansubstantially reduce the number of experiments and forthis reason a small CCD with five levels was selected todevelop the first order and second order models. This isthe most popular class of designs used for fitting thesemodels and has been established as a very efficientdesign for fitting the second order model [12]. Theanalysis of mathematical models was carried out usingDesign Expert version 6.0 package for both the first andsecond order models. The machining process carried outin random manner in order to reduce the error due tonoise. The overall cutting conditions and thecorresponding values of surface roughness are presentedin Table 2.4. Results and DiscussionThe surface roughness values have been presented inthe last column of Table 2. Significant variation isobserved in surface finish of the milled face of the work-piece. The maximum value of Ra is O.l6? ~ w~ereasthe minimum value is 0.055 urn, ThIS significantvariation in surface roughness cannot be explained in asimple way as there are main individual and interactiveeffects of the cutting parameters.4.1 Development of first and second order modelsUsing the experimental results as obtained in theform of surface roughness values against' all the setexperimental conditions, the following surfaceroughness prediction model has been developed.In R. = 1.704 - 0.778 In X, + 0.382 X2 + 0.328 X3 (6)This is a first order model. By substituting Eq.(5)into Eq.(6), the model finally can be expressed as :R, = 5 .49V -0.78 d 0.38 f 0.33 (7)-48-Table2' Cuttingconditionsand surfaceroughnessresultsobserved data at the 95% confidence level. Fig. 1,2, and 3show the 3D contour of predicted surface roughnessresults generated by the quadratic CCD model. Thegraphs demonstrated that by machining at high feed withlow cutting speed and low depth of cut surface roughnessvalues will be lower and vice versa.Std. Location CodedForm ActualForm Responseorder inCCD Cutting Depth of feed SurfaceXI X2 X3 speed cut (rnmItoo Roughness(rn/min) (rnm) th) (urn)1 Factorial +1 +1 -I 72.28 1.63 0.025 0.0552 Factorial +1 -1 +1 72.28 0.61 0.079 0.0653 Factorial -1 +1 +1 44.27 1.63 0.079 0.1604 Factorial -1 -I -1 44.27 0.61 0.025 0.0705 Center 0 0 0 56.57 1.00 0.044 0.0806 Center 0 0 0 56.57 1.00 0.044 0.0707 Center 0 0 0 56.57 1.00 0.044 0.0808 Center 0 0 0 56.57 1.00 0.044 0.0709 Center 0 0 0 56.57 1.00 0.044 0.07510 Axial -1.414 0 0 40.00 1.00 0.044 0.10511 Axial +1.414 0 0 80.00 1.00 0.044 0.08012 Axial 0 -1.414 0 56.57 0.50 0.044 0.07513 Axial 0 +1.414 0 56.57 2.00 0.044 0.13514 Axial 0 0 -1.414 56.57 1.00 0.02 0.07515 Axial 0 0 +1.414 56.57 1.00 0.10 0.110From this 1st order model (Eq.7) it is apparent thathigher cutting speed will lower the Ra values whereas theeffects of depth of cut and feed are opposite leading to theadverse surface roughness. This equation is valid forcutting speed (40~V~80), depth of cut (0.5~d~2) and feed(0.02~f~O.l). Since the second-order model is veryflexible, easy to estimate the parameters with method ofleast square error, and work well in solving real responsesurface problems [3], the analysis was extended inprediction of more robust modeling of surface roughness.Using the experimental data in Table 2, the second orO&1''''model is derived with the following equation:In R. = -2.492 - 0.096X1 + 0.186X2 + 0.135X3 + X220.I13XIX2 + O.l89XzX3 (8)This model takes into account of the interactive andquadratic effects of the cutting variables. However it doesnot contain the terms representing XIZ, X32 and XIX)because the effects are insignificant and/or of lowercoefficients. Both Eq. (7) and (8) representing Ist and 2ndorder CCD models respectively have indicated that depthof cut would give significant effect on surface roughnessvalues followed by feed and cutting speed.4.2 Analysis of VarianceTable 3 showing the ANOVA for 1st order (linear)CCD model indicates the significant level of each effectand lack of fit. The model is found to be significant withF-value less than 0.05. Lack of fit value of 0.0818 impliesthat it is not significant at 95% confidence interval leadsto make an inference that the model is significant. In thiscase all the independent variables are significant. Thismeans that since the P value for lack of fit test is greaterthan 0.05, the model is appears to be adequate for the·1.7198·1.96417·2.20853/',~(ij' ·2.4529et:co ·2.69726...J1.00 ,//" /"0.50 /"'./ /./" /,/" "../'0.00<>://://0.000.50B:.Depth of cut ·0.50 ·0.50A: Cutting speed·1.00 ·1.00Figure I: The 3DResponseSurfaceof TheQuadraticCCDModel atX3= 1.0 or feed = 0.079 mmltooth-49-·2.02108.2.1915~-2.50234'"C -2.66276...J •..' ,,-1""''''' 1.000.50 // .'/' 0.500.00 //' ..0.00»:8: Depm 01cut ·0.50 ·0.50 A:. Cutting speed·1.00 -1.00Figure2: The 3DResponseSurfaceof TheQuadraticCCD Modelat X3 = 0.00 or feed = 0.044 mm/tooth·2.30128-2.42746·2.55365(Q"-2.67983'"C ·2.90601...J0.500.000.008: Oeplh 01 cut ·0.50 ·0.50 A:. Cutting speed·1.00 ·1.00Figure3: The 3DResponseSurfaceof The QuadraticCCD Modelat X3 = -1.0 or feed = 0.025 mm/toothTable 3' ANOVA of 1st order(linear)CCDModelP>O.ISum of DF Mean FProb>Source Squares Square Value F model notsignificantBlock 0.15 I 0.55Model 0.86 3 0.29 20.60 0.0001 significantA 0.29 I 0.29 20.84 0.0010B 0.28 I 0.28 19.87 0.0012C 0.29 1 0.29 21.08 0.0010Residual 0.14 10 0.014Lack0.12 6 0.020 4.56 0.0818notof Fit significantPureError 0.Ql8 4 0.0044Cor US 14TotalTable 4 showing the ANOVA for 2nd order(Quadratic) CCD model indicates the significant level ofeach effect and lack of fit. From the table, it is clear thatthe squares of cutting speed and feed (A2 , C2 ) andinteraction between cutting speed and feed (AC) havelow influence on the Ra since their P-values are more than0.1. Hence these terms have been removed from theequation in order to further analyse the experiment. Theresults so obtained are shown in Table 5. It is apparentthat the model is significant with P-value less than 0.1with the value of lack of fit is more than 0.1. It indicatesthat after adjustment the model becomes morepronounced and reliable. Figure 4 and 5 show acomparison between experimental values and predictedvalues generated by quadratic CCD 2nd order model and1st linear model. Both of the models are adequate topredict the surface roughness values quite reliably as thedeviations of the theoretical and experimental values arevery smalL0,00 ..•...•...•.....•.•.........•........•.•.•..•...•.•.................................................. ,I·0,50 I---;:===========:=::~----jI--+- Actual Valle ~;=:- A'e<flCted Value I·1.00 -I---.!=========='----l•• 'I,SO t-------------------ll:.5 .2,00 +-_-1/-'»\\------------,:'r---i1\ />; 1\;·2,50 t---+--T--====-",'---\;!::::-:;;!----'.;;/----li \~'-~'~"?' .....•.••<-·3,00 t-'::...,.-"-.--------------i·3,SO+--~-_,_---.--~-__._-~-_-_io 2 10 12 14Standard OrderFigure4: ComparisonBetweenExperimentalValuesandCCDQuadraticPredictedResults0,00 .-O,50t-----------------~.1,00 +---~_+_Actual Value-s--Predlcted Value-;;,1,50 t--------------~'---_!l:.5.2,00 '-- __ -If't...,"'.\\ --,,..-_---, .•_--.,--;.- 1/1 ", $\ ~f \~ /A /'\, l·2,50 t---f-*--====,.......,.fL--.:-..r.-.,;....----",d--~:::>i \!::~~'¥~=«: ~;ff :.s:::::.~' "~'·3,00t-..:..-----------------i·3,50 t--_,_--,--~-___.-__,,_-..__-_._-_io 1210 14Standard OrderFigure5: ComparisonBetweenExperimentalValuesandCCDLinearPredictedResults-50-16.!16Table 4' ANOVA of2nd order (Quadratic) CCD ModelF P>O.ISum of Mean Prob>Source Squares OF Square Valu F (model notesignificant)Block 0.15 I 0.15Model 0.99 9 0.11 24.57 0.0037 significantA 0.037 I 0.037 8.29 0.0450B 0.17 I 0.17 38.74 0.0034C 0.073 I 0.073 16.45 0.0154A2 0.0002 0.0002notI 0.064 0.8133significantB2 0.021 I 0.021 4.70 0.0961 significantC2 0.00002 I 0.00002 0.004 0.9494 notsignificantAB 0.026 I 0.026 5.73 0.0749 significantAC 0.0037 I 0.0037 0.83 0.4149notsignificantBC 0.072 I 0.072 16.08 0.0160 significantPure0.018 4 0.0044ErrorCor 1.15 14TotalTable 5: ANOVA of 2nd order (Quadratic) CCD Model -modifiedP>O.ISum of DF Mean F Prob>(model notSource Square Square Value F significant)Block 0.15 I 0.15Model 0.98 6 0.16 52.51 0.0001 significantA 0.037 I 0.037 11.87 Om08B 0.28 I 0.28 89.16 0.0001C 0.073 I 0.073 23.54 0.0019B2 0.021 I 0.021 6.65 0.0365AB 0.026 I 0.026 8.20 0.0242BC 0.072 I 0.072 23.01 0.0020Residual 0.022 7 0.003Lack of0.004 3 0.001 0.30 0.08266notfit significantPure0.018 4 0.004ErrorCor Total 1.15 145. ConclusionsThis research work was undertaken to develop amathematical relationship between the surface roughnessin end milling of hard material (AISI' D2) and themachining variables by using the experimental resultsobtained through use of the concept of RSM. It has beenpossible to develop the first order (linear model) as wellas the second order (quadratic model). Adequacy orvalidity of the models has been evaluated by ANOVAwhich indicates that the models are reliable. Thesemodels can be safely used to predict the surfaceroughness of the machined part of AISI D2 tool steelunder the specified cutting conditions. These models arevalid within the ranges of the cutting parameters in endmilling which for cutting speed range is 40 - 80 mlmin,for depth of cut range is 0.5 - 2.0 mm and for feed rangeis 0.05 - 0.1 mmltooth. Both models linear (I" order) andCCD quadratic (2nd order) have shown similar trendsindicating that the depth of cut has the most significantinfluence on surface roughness followed by feed andcutting speed. However, the values of depth of cut andfeed are not much different coefficients meaning thattheir influences on roughness are very close.AcknowledgementThis study was conducted under the purview of the e-science project (03-01-08-SF0003) entitled"Enhancement of Machinability of Hardened Steel in EndMilling Using Advanced Cutting Methods and Tools",funded by the Ministry of Science, Technology andInnovation of Malaysia (MOST!). The authors gratefullyacknowledge the financial support.References[1] LN. Lopez de Lacalle, A. Lamikiz, lA. Sanchez,lL. Arana, Improving the surface finish in high-speed milling of stamping' dies, Journal of MaterialProcessing Technology, 123 (2002) 292-302.[2] P.G. Benardos and G.C. Vosniakos, Predictingsurface roughness in machining: a review,International Journal of Machine Tools &Manufacture, 43 (2003) 833-844[3] Raymond H. Myers and Douglas C. Montgomery,Response surface methodology: Process and productoptimization using designed experiments, 2ndedition, John Wiley & Sons, USA, 2002.[4J Wu, S.M., 1964. Tool life testing by responsesurface methodology, Part I and Part II. J. Eng. Ind.,pp: 105-116.[5] Kuang-Hua Fuh and Chih-Fu Wu, 1993, A ProposedStatistical model for Surface Quality Prediction inEnd-Milling of Al alloy, Int. J. Mach. ToolsManufact, Vol. 35, No. S, pp. 1187-1200. 1995[6] M. Alauddin, M.A. EI Baradie, M.SJ. Hashmi,1996, Optimization of surface finish in end millinginconel 718, Journal of Material Processing andTechnology 56, pp. 54 - 65.-51-[7] H. Oktem, T. Erzurumlu, H. Kurtaran, 2004,Application of response surface methodology in theof cutting conditions for surface roughness, Journalof Materials Processing Technology 170 (2005) 11-16[8] H.Z. Li, H. Zeng, X.Q. Chen, An experimentalstudy of tool wear and cutting force variation in theend milling of inconel 718 with coated carbideinserts, Journal of Material Processing Technology,180 (2006) 296-304.[9] J. Vivancos, C.J. Luis, J.A. Ortiz, HA Gonzalez,Analysis of factors affecting the high-speed sidemilling of hardened die steels, Journal of MaterialProcessing Technology, 162-163 (2005) 696-70 l.[10] A. Mansour and H. Abdalla, Surface roughness forend milling: a semi-free cutting carboncasehardening steel (EN32) in dry condition, Journalof Material Processing Technology, 124 (2002) 183-19l.[11] H.Z. Li, H. Zeng, X.Q. Chen, An experimentalstudy of tool wear and cutting force variation in theend milling of inconel 718 with coated carbideinserts, Journal of Material Processing Technology,180 (2006) 296-304. .[12] Douglas C. Montgomery, Design and analysis ofexperiments, 6th edition, John Wiley & Sons, USA,2005..1-52-

Prediction of surface roughness in hard milling of AISI D2 tool steel

http://irep.iium.edu.my/26885/1/Ra_AISI_D2_%2321.pdf

Prediction of surface roughness in hard milling of AISI D2 tool steel

Abstract

Similar works

Full text

Available Versions

The International Islamic University Malaysia Repository