This paper deals with the development of an indigenous technology for a widely used silver brazing alloy (BAg-1). Melting, alloying, casting and processing along with the heat treatment schedules, have been dealt with. Particular emphasis has been laid on the corrosion behaviour of this alloy

Dev, S C

Sivaramakrishnan, C S

English

eprints@NML

Marerids & Design. Vol. 17, No. 2, pp. 75-78, 1996 Copyright r%j 1996 Elsevier Science Ltd Printed in Great Britain. All rights reserved 0261-3069/96 $15.00 + 0.00 PII: SO261-3069/96)00035-O An indigenous technology for a silver brazing alloy S.C. Dev and C.S. Sivaramakrishnan” National Metallurgical Laboratory, Council of Scientific and Industrial Research, Jamshedpur 831007, India Received 22 May 1996; accepted 24 July 1996 This paper deals with the development of an indigenous technology for a widely used silver brazing alloy (BAg-1). Melting, alloying, casting and processing along with the heat treatment schedules, have been dealt with. Particular emphasis has been laid on the corrosion behaviour of this alloy. Copyright 0 1996 Elsevier Science Ltd Keywords: silver brazing alloy; wetting; corrosion and mechanical properties Introduction Silver brazing alloys of the American Welding Society’s specification are best suited as filler material for joining ferrous and non-ferrous metals, and alloys’~2. Of these, BAg-1 containing 4244%Ag, 15-15%Cu, 18-22%Zn and 20-22%Cd, is an alloy for general purpose applications; and is widely used for brazing steel, copper, brass, gun metal, tin bronze, aluminium bronze, manganese bronze, silver based contacts, nickel based alloys and nickel silver of all types3.4. This alloy has free flowing characteristics and a narrow melting range. It is essentially an alloy for use, where joints are closely fitted, or where it is desired to employ a single brazing alloy that will be effective in a wide range of applications. The entire requirement of this brazing alloy is either met by importing or manufacturing using imported technology. Problems are encountered during the indigenous pro- duction of sound ingots/slabs, heat treatment and proces- sing, like rolling, wire drawing etc. for making thin sheet/ wire of BAg-1 alloy. Cadmium and zinc are highly oxidisable metals and this factor plays an important role in controlling the loss of these elements during melting. Also, the wide differences in melting points and densities (Table 1) of the alloying elements cause problems in the production of homogeneous ingots/slabs. A detailed experimental programme was undertaken at the National Metallurgical Laboratory to indigenise the production technology of this brazing alloy. This involved establishing the processing parameters, such as melting, alloying, casting, heat treatment and rolling into thin sheets/wires for brazing applications. Experimental Silver, copper, zinc and cadmium of 99.9% purity were used for the preparation of the alloy. Copper and silver were melted together in an electric resistance furnace in a *Corresponding author. clay bonded graphite crucible. Preheated zinc and cadmium were added with a cover of borax flux on the molten surface to protect them from oxidation and loss. The compositions of the experimental and imported standard alloys are given in Table 2. The homogenised melt was poured in a preheated steel mould in the temperature range 700-750°C. Experimental alloys, each weighing 500 to 1000 g were made using the above procedure. Heat treatment and processing The cast ingots/slabs were given a certain amount of reduction by rolling them at the room temperature prior to the heat treatment, to reduce the conventional long homogenisation period (24 h) to 6-8 h at 400+6O”C. The homogenised slabs/ingots were then rolled into thin sheets using intermediate annealing heat treatment. Evaluation of properties Wetting properties Wettability tests for both the indigenous and imported alloys were done on copper and steel base plates by placing a cubical sample, having a length of 3 mm, at the centre of base plates, having dimensions 24 mmx 12 mmx 1 mm, and heating in Leitz Wetzlar heating microscope (Germany). A thermocouple was placed below the base plate and the assembly was put inside a tube furnace. A Leitz microscope was attached to the furnace to monitor the softening process in-situ, under argon atmosphere. Direct photographs of the contact angles of the alloys on the base plates at a brazing temperature (650°C) were taken and measured. Mechanical properties The mechanical properties, such as tensile strength, hardness and elongation, as well as the brazed joint strength for both the indigenous and imported alloys were Materials & Design Volume 17 Number 2 1996 75 Silver brazing alloy: S. C. Dev and C. S. Sivaramakrishnan Table 1 Melting points and densities of alloying elements for BAg-1 Silver brazing alloy Element Melting point (“C) Density (g cmm3) Silver 961 10.50 Copper 1083 8.94 Zinc 419 7.13 Cadmium 321 8.64 Table 2 Compositions of the imported and indigenous brazing alloys CU” Zn” Cd” Aga Indigenous alloy Standard alloy (BAg- 1) 16 20 20 balance 15-17 18-22 20-22 balance a wt.% determined. Instron tensile testing machine was used for tensile strength and Vickers Hardness tester for hardness. Corrosion properties Electrochemical studies of the imported and indigenous alloys were done using a microprocessor based potentio- stat/galvanostat (PARC-273 A) in 3.5% NaCl and 1% Na$ solutions, respectively, at a scan rate of 2 mV s-’ at the room temperature. A saturated calomel electrode and graphite rod were used as a reference and an auxiliary electrode, respectively. A surface area of 1 cm2 was exposed for the test. The corrosion current (I,,,), open circuit potential (OCP) and corrosion rate were determined. For the atmospheric corrosion test, standard sized, mirror finished test specimens were exposed at an angle of 45” in industrial and marine atmospheres, at Jamshedpur and the sea shore at Digha, respectively, and the corrosion rates after 30, 90 and 180 days of exposure were determined by weight-loss method. The industrial atmo- sphere contained sulphuroxides, carbondioxide, hydrogen sulphide, ammonia and chlorine gas. The marine atmo- sphere mainly comprised sodium chloride, moisture etc. Metallographic studies Optical microscopic studies were done on cast and homogenised samples. Service trials Silver based contact tips were brazed to a backing material (copper) with both the indigenous and imported brazing alloys, and tested for their endurance performance in the breaking and making of electrical circuits in railways and different steel plants under heavy current loads. Results and discussion The variation in the total loss of weight for different melts due to the oxidation of zinc and cadmium during the melting of the alloy are shown in Figure 1. The curve shows that the loss of cadmium and zinc decreases as the total quantity of the melting charges increases. An amount of 500 g and above of the charge would be economical for the melting of the alloy. The authors have also studied the effect of the size of the cadmium and zinc metal pieces to be added to the molten alloy during melting. It is found that the weight of each piece of zinc and cadmium should be 2- 5% of the weight of Ag-Cu of the charge to prevent the excessive loss of cadmium or zinc. The addition of cadmium or zinc pieces heavier than that mentioned above had been found to chill the bath of the molten metal, whereas lighter pieces increase the loss of metals. It is evident from the processing steps (Figure 2) that the homogenisation time has been reduced from 24 hours to 8 hours by reduction, at the room temperature prior to homogenisation. Microstructures of the cast and homo- genised samples are shown in Figure 3. It can be seen that the dendritic structure disappears on homogenisation. The initial reduction at the room temperature improves the kinetics of the homogenisation by reducing the effective diffusion distance?. During the processing of the homogenised slabs by rolling, it is observed that the initial reduction of the slab should not be more than 20-25% until it has been reduced by 45%. Then, with intermediate annealing in the range 400-45O”C, the slab could be reduced to a thin sheet having a thickness of 0.15-0.05 mm with a 35-40% reduction, at each cycle of rolling. The physical properties of the silver base brazing alloys studied are given in Table 3. The solidus and liquidus temperatures, densities and electrical conductivities are also reported which are very close for both the imported and indigenous alloys. Table 4 shows the 01 1 I I I / 1 I i 1 100 200 300 400 500 600 700 800 900 1000 WEIGHT OF CHARGE IN GRAMS - Figure 1 Variation in loss of weight of charge due to oxidation of Cd and Zn 76 Materials & Design Volume 17 Number 2 1996 Silver brazing alloy: S. C. Dev and C. S. Sivaramakrishnan cast Slab 25mm Thick (0) #mwgenised Cold Rcdn Annealing Rolled . Thin 20 -2 5 ‘I, Sheet Cold Redn. Sheet 35-40’1. 0.10 mm Thick cost ~gen&.d Wd. Redn Anne~liflg Thin Slab Slab 20 -25 ‘I. Cold, Redn Sheet 25 mm Thick 460’C/8h 35-40 ‘1. O.lOmmThick (b) Figure 2 Processing schedule for the brazing alloy: (a) conventional and (b) modified in the present work Figure 3 Photomicrographs of the indigenous brazing alloy under various conditions: (a) as cast, (b) homogenised at 460°C for 24 h and (c) reduced by rolling at room temperature prior to homogenisation at 460°C for 8 h Table 3 Physical properties of the brazing alloy wetting properties, such as contact angles, spreading area Alloy Temperature (‘C) Density Electrical and wetting index. It is evident that the values are nearly the (g cmm3) conductivity same for both the imported and indigenous alloys. Solidus Liquidus (%IACS) Hardness, yield strength, tensile strength and elongation Imported 610 620 9.2 25.28 are shown in Table 5. The indigenous alloy shows better Inditenous 605 618 9.4 27.30 values. The brazed joints (Cu-Cu and steel-steel) were tested for mechanical properties and the values are shown in Table 6. It is evident once again that the values for both Table 4 Wetting properties of brazing alloys Alloy Brazing temp (“C) Atmosphere Contact angle (“) (0) Wetting area [in2 (mm2)] (A) Wetting index (WI)* Imported (a) 650 Argon 16 0.300 (192) 0.29 (b) 650 Argon 20 0.26 Indigenous 0.280 (179) (a) 650 Argon 18 (b) 650 0.300 (192) 0.29 Argon 20 0.200 (186) 0.27 * Wetting index=A cos ClzO. 10 shows excellent performance during brazing Materials & Design Volume 17 Number 2 1996 77 Silver brazing alloy: S. C. Dev and C. S. Sivaramakrishnan Table 5 Mechanical properties of the brazing alloys Alloys Hardness (VPN) Yield strength (MPa) UTS(MPa) % Elongation Imported 100 180 350 30 Indigenous 105 200 400 35 Table 6 Mechanical properties of the brazed joints Alloy Impact strength (Kg m) Shear strength (MPa) UTS W’a) Location of fracture Imported Indigenous a 2.8 120 300 Joint b 3.0 100 170 Base metal a 3.0 120 350 Joint b 3.0 110 180 Base metal u for steel to steel and b for copper to copper joints Table 7 Polarisation data of the brazing alloys Alloy 3.5% NaCl solution 1% NazS solution OCP(-V) I corn Corrosion GCP(-V) I corr Corrosion rate (m y-t) rate (m yy’) Imported 0.430 1.33 0.435 1.420 10.30 3.40 Indigenous 0.4366 1.318 0.433 1.412 10.10 3.35 Table 8 Atmospheric corrosion test results for the brazing alloys Alloy Exposure time Corrosion rate (m y-‘) (days) Industrial Marine atmosphere atmosphere Imported 30 0.0865 0.339 90 0.0520 0.234 180 0.0176 0.198 Indigenous 30 0.0880 0.343 90 0.0500 0.230 180 0.0170 0.203 the imported and indigenous alloys are similar or the indigenous alloy gives better values. Table 7 gives the polarisation data in NaCl and NaaS solutions at the room temperature. Appreciable changes in the corrosion proper- ties of the alloys are not observed. The atmospheric test results for 30, 90 and 180 days of exposure in industrial and marine environments are given in Table 8. It is evident that both the imported and indigenous alloys have similar corrosion behaviour. Conclusions The indigenously produced silver based brazing alloy possesses imilar mechanical and physical properties as the imported BAg-1 brazing alloy. The alloy was tested in industrial and marine atmospheres along with the imported alloy, and both were found to be equally corrosion resistant. The brazed joints with indigenous alloy tested for tensile strength showed that the strength properties are better than those of the imported alloy. Recommendation for further work Further work could be undertaken to study the wettability characteristics of the alloy incorporating some microaddi- tions, like indium, bismuth etc. Detailed corrosion studies could also be studied under longer exposures. Acknowledgements The authors wish to extend their thanks to the Director, National Metallurgical Laboratory for his kind permission to publish this work and to D.K. Basu for carrying out the corrosion tests. References Dev, S.C., Basak, I?, Singh, lnder, Dubey, R.K. and Mohanty, O.N., J. Mat. Sci., 1992, 27, 6646. Barnett, O.T., Filler metals for joining. Chapman and Hall, London, 1959, p. 205. Indian Standard Specification for Brazing alloys. IS 2927.1975, 1st Dec., 1975. Chamer, E.S., Silver-Economics, Metallurgy and Uses, eds A Butt and C. D. Coxe. Kriger, Hintington, 1975, p. 386. Shewmon, P.G., Transformation in Metals. McGraw Hill, New York, 1969, p. 42. Feduska, W., Welding J., 1959, 38(3), 131s. McDonald, M.M., Heiple, C.R. et aZ., Supplement to Welding J., Oct. (1989) 391s. D. L. Keller, M. M. McDonald ef al., Welding J., Oct. 1990, 33. 78 Materials & Design Volume 17 Number 2 1996 

An indigenous technology for a silver brazing alloy

http://eprints.nmlindia.org/410/1/S._C._Dev(16).pdf

An indigenous technology for a silver brazing alloy

Abstract

Similar works

Full text

Available Versions

eprints@NML