This article presents a low-power, high-linearity cascodetype low noise amplifier (LNA) with 36 dB of variable gain for the WIDE Code Division Multiple Access systems. By enhancing the substrate resistance of a common gate transistor along with adopting multiple-gate technique, the linearity is significantly improved. Shunt-current steering is adopted for smooth gain control. Step gain mode is used to further increase the gain control range. The main common source transistor is disabled in attenuation mode, saving unwanted power consumption.

Measurements show maximum gain of 12.3 dB with S11 of 19.5

dB, and S22 of 14 dB. The total gain control range is 36 dB. NF is measured as 2 dB and two-tone test shows 9.1 dBm of IIP3. Implemented in 0.13-m CMOS technology, the LNA consumes only 1.6 mA at maximum gain mode and only 0.2 mA in attenuation mode from 1.2 V supply. Its die size is 0.3 mm2. © 2009 Wiley Periodicals, Inc. Microwave Opt Technol Lett 51: 1385–1388, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.

2432

Farrell, Ronan

Gug-Lee, Sang

Tuan-Phan, Anh

English

MURAL - Maynooth University Research Archive Library

is 1.25 dB with a return loss better than 28 dB. Two transmissionzeros are observed with attenuations over 40 dB at approximately1.43 and 1.93 GHz, respectively. Meanwhile, the measured 3-dBrelative bandwidth is about 9.35%. Figure 3(b) describes themeasured in-band group delay. The wideband responses, shown inFigure 3(c), illustrate that the first spurious pass-band is located at3.18 GHz, i.e. about 2f0. When comparing the measurements withpredicated results, one can see that a good agreement betweenthem can be observed.4. CONCLUSIONIn this article, a compact dual-mode patch resonator for band-passfilter applications has been studied. A demonstrator filter using adual-cross slot has been designed, fabricated and tested. Measureddata indicate the filter has a minimum pass-band insertion loss 1.25dB as well as a pair of transmission zeros close to the pass band.The filter has a size reduction to 26.7% as compared to theconventional patch resonator. The design concept is validated,theoretically and experimentally, with good consistency.REFERENCES1. J.-S. Hong and M.J. Lancaster, Microstrip filters for RF/microwaveapplications. Wiley, New York, 2001, Ch. 11.2. I. Wolff, Microstrip bandpass filter using degenerate modes of amicrostrip ring resonator, Electron Lett 8 (1972), 302–303.3. B.T. Tan, S.T. Chew, M.S. Leong, and B.L. Ooi, A dual-mode band-pass filter with enhanced capacitive perturbation, IEEE Trans Micro-wave Theory Tech 51, (2003), 1906–1910.4. A. Go¨ru¨r, A novel dual-mode bandpass filter with wide stopband usingthe properties of microstrip open-loop resonator, IEEE MicrowaveWireless Compon Lett 12, (2002), 386–388.5. A. Gorur, Description of coupling between degenerate modes of adual-mode microstrip loop resonator using a novel perturbation ar-rangement and its dual-mode bandpass filter applications, IEEE TransMicrowave Theory Tech 52, (2004),671–677.6. S. Amari, Comments on description of coupling between degeneratemodes of a dual-mode microstrip loop resoantor using a novel pertur-bation arrangement and its dual-mode bandpass filter applications,IEEE Trans Microwave Theory Tech 52, (2004), 2190–2192.7. S.-W. Fok, P. Cheong, K.-W. Tam, and R. P. Martins, A novelmicrostrip square-loop dual-mode bandpass filter with simultaneoussize reduction and spurious response suppression, IEEE Trans Micro-wave Theory Tech 54, (2006), 2033–2041.8. S.J. Fiedziuszko, J.A. Curtis, S.C. Holme, and R.S. Kwok, Low lossmultiplexers with planar dual mode HTS resonators, IEEE TransMicrowave Theory Tech 44, (1996), 1248–1257.9. J.-S. Hong, and S.-Z. Li, Theory and experiment of dual-mode mi-crostrip triangular patch resonators and filters, IEEE Trans MicrowaveTheory Tech 52, (2004), 1237–1243.10. L. Zhu, P.-M. Wecowski, and K. Wu, New planar dual-mode filterusing cross-slotted patch resonator for simultaneous size and lossreduction, IEEE Trans Microwave Theory Tech 47, (1999), 650–654.11. O. Akgun, B.S. Tezekici, and A. Go¨ru¨r, Reduced-size dual-modeslotted patch resonator for low-loss and narrowband bandpass filterapplications, Electron Lett 40, (2004),1275–1276.12. L. Zhu, B.C. Tan, and S.J. Quek, Miniaturized dual-mode bandpassfilter using inductively loaded cross-slotted patch resonator, IEEEMicrowave Wireless Compon Lett 15, (2005), 22–24.13. W.-H. Tu and K. Chang, Miniaturized dual-mode bandpass filter withharmonic control, IEEE Microwave Wireless Compon Lett 15, (2005)838–835.14. IE3D Manual, Zeland Software, Fremont, CA, 2001.© 2009 Wiley Periodicals, Inc.9.1 dBm IIP3 36 dB GAINCONTROLLABLE LNA FOR WCDMA IN0.13-m CMOSTuan Anh Phan,1 Ronan Farrell,1 and Sang-Gug Lee21 Institute of Microelectronics and Wireless Systems, NationalUniversity of Ireland, Maynooth, Kildare, Ireland; Correspondingauthor: aphan@eeng.nuim.ie2 Information and Communications University, Daejeon, KoreaReceived 13 September 2008ABSTRACT: This article presents a low-power, high-linearity cascode-type low noise amplifier (LNA) with 36 dB of variable gain for theWIDE Code Division Multiple Access systems. By enhancing the sub-strate resistance of a common gate transistor along with adopting multi-ple-gate technique, the linearity is significantly improved. Shunt-currentsteering is adopted for smooth gain control. Step gain mode is used tofurther increase the gain control range. The main common source tran-sistor is disabled in attenuation mode, saving unwanted power consump-tion. Measurements show maximum gain of 12.3 dB with S11 of 19.5dB, and S22 of 14 dB. The total gain control range is 36 dB. NF ismeasured as 2 dB and two-tone test shows 9.1 dBm of IIP3. Imple-mented in 0.13-m CMOS technology, the LNA consumes only 1.6 mAat maximum gain mode and only 0.2 mA in attenuation mode from 1.2 Vsupply. Its die size is 0.3 mm2. © 2009 Wiley Periodicals, Inc.Microwave Opt Technol Lett 51: 1385–1388, 2009; Published online inWiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.24320Key words: LNA; variable gain control; high linearity; CMOS;WCDMA; low-power1. INTRODUCTIONWIDE Code Division Multiple Access (WCDMA) receiver sys-tems require high linearity due to cross modulation distortion(XMD) [1]. Once the signal-to-noise ratio (SNR) is degraded at thelow noise amplifier (LNA) by XMD, designing the followingstages to satisfy linearity and power consumption requirementsmay be difficult. Also, to achieve a wide system dynamic range ofover 80 dB, the LNA must have several gain modes so as not tosaturate the following stages. Besides those main challenges, theLNA should have a good performance with high enough gain, lownoise figure (NF), and low power consumption.There have been several efforts to improve the linearity per-formance of the LNA for CMOS technology. Feed-forward can-cellation technique introduced in [2] is useful for differentialapplication, but it requires an additional external power splitterwhich would be a cost increase. The active postdistortion tech-nique [3] and derivative super-position (DS) [4] are quite effectivebut with the cost of higher noise. The modified derivative super-position (MDS) method is attractive because it can increase lin-earity significantly with wide DC operating range [5]. In thismethod, however, it is not easy to control the opposite phase ofthird order product to obtain the desired high level of linearity.Thus, a new technique to further increase the linearity is intro-duced.In this article, a high-linearity variable gain cascode-type LNAfor WDCMA systems is presented. The linearity is significantlyimproved when the DS method is adopted together with enhancingthe substrate resistance of common gate transistor without anyperformance penalty in power consumption, noise, and gain. Toextend the gain control range, smooth and step gain control tech-niques are combined. Implemented in 0.13-m CMOS processwith Deep N-Well, the proposed LNA obtained 9.1 dBm of IIP3DOI 10.1002/mop MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 51, No. 5, May 2009 1385and 36 dB of variable gain range while consuming only 1.6 mA at1.2 V supply.2. LINEARITY IMPROVEMENT APPROACHThe cascode-type LNA can be considered as two cascaded stagesconsisting of the common source (CS) and common gate (CG)transistors. The role of a preceding CS transistor is to provide thegain and suppress the noise through input matching. This transcon-ductance device linearity is usually more important because itintroduces more nonlinearity products to the output more than thecascode device (CG). Therefore, most of the linearization tech-niques have focused on the transconductance device as mentionedin the previous section. In this article, the approach is different. Weassume that the transconductance has been fully linearized and thesubsequent CG stage, which acts as current buffer, is the bottle-neck of the linearity. Moreover, if we treat the transconductanceand cascode devices as the two cascading stages, the subsequentcascode device will dominates the overall linearity performance atthe output. Thus, the overall LNA linearity will be maximizedwhen both the CS and CG are linearized, especially the CG.So far, most of the linearization methods for a CMOS LNAhave focused on the CS stage. The most effective technique isderivative superposition (DS). This method cancels out the nega-tive third-order derivative of the main field-effect transistor’s(FET’s) dc transfer characteristic by paralleling the auxiliary FETbiased near the weak inversion region with the positive one. In thisdesign, DS is adopted but the linearity does not satisfy the systemrequirement because it is hard to adjust the bias and FET’s size toachieve complete IM3 cancellation.Therefore, to obtain further linearity, a linearization techniqueat the CG by adopting substrate resistance enhancement is pro-posed. The model of a NMOSFET in a deep N-well process isshown in Figure 1 with presence of an external resistor Rsubbetween bulk terminal and ground. From the substrate modelshown in Figure 1(b), a strong signal may turn on the parasiticsource-bulk (Dsb) or drain-bulk (Ddb) diodes, which clips thesignal itself. That effect reduces the power handling capability orlinearity of the MOSFET device. Because of that, the linearity canbe improved by bootstrapping the bulk voltages [6, 7], which isrealized by floating the bulk at RF. By isolating the bulk fromground with Rsub, distortion source cannot interfere the main signalpath.In contrast, the body and source of common source FETs aretied together to minimize the body effect and substrate resistance.Because it is well known that the higher the substrate resistance ofCS transistor, the lower are its output resistance and transconduc-tance, thus reducing the maximum available gain.Figure 2 presents the linearity performance (IIP3) of the LNAversus the external substrate resistance (Rsub) by simulating withdifferent Rsub values. When Rsub goes from 700 to 4 KOhm, thelinearity shows a sharp increase in IIP3. With Rsub over 4 KOhm,linearity performance is saturated and not much improved com-pared to the IIP3 at 4 KOhm of Rsub.3. LNA TOPOLOGY AND CIRCUIT DESIGNThe proposed LNA schematic using cascode topology is shown inFigure 3. Inductive load peaking (RL, LL) is used for widebanddesign. Mm and Mex are the main and auxiliary FETs for DStechnique, respectively. LG, CGS, and LS are input the matchingnetwork. CGS is used to reduce the size of Mm for noise and inputsimultaneous matching with power constraint.The Rsub is inserted between the body of CG transistor andground. Thus the body is highly isolated from ground, avoidingany feedback loop which may cause the signal distortion. It alsohelps reducing the resistive losses in the conductive P-well be-tween D and S because the bulk resistance is open to the ground.In this design, Rsub is selected as 5 k Ohm.Continuous gain control is realized by steering the signal awayfrom the load through a branch consisting of Ccouple and Msteer.Ccouple is for DC blocking and AC signal coupling. As the MsteerFigure 1 (a) Cross-sectional view and (b) substrate model of MOSFET.[Color figure can be viewed in the online issue, which is available atwww.interscience.wiley.com]Figure 2 Simulation of IIP3 performance vs. the value of Rsub1386 MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 51, No. 5, May 2009 DOI 10.1002/mopis ON, low on-resistance creates another path for signal to theground apart from the main signal path to the output. Thus,depending on the amount of signal steered away, the signal ap-pearing at the output can be controlled. To increase the range ofgain control, step gain control is combined with continuous gaincontrol. Four step gain modes are obtained corresponding with theON/OFF operation of Mm and Msteer. That is maximum, medium,attenuation, and minimum gain modes when Mm is ON and Msteeris OFF, both Mm and Msteer are ON, Mm is OFF and Msteer is OFF,and Mm is OFF and Msteer is ON, respectively.In the DS method, the subthreshold-biased FET (Mex) gener-ates more noise than the saturation-region biased one [2]. Hence,the auxiliary FET is designed with small size to minimize parasiticcapacitance and noise contribution.4. EXPERIMENTAL RESULTSThe proposed LNA is designed and fabricated in TSMC 0.13-mCMOS technology using 1.2 V supply.Measurements show 12.3 dB of gain with good input andoutput matching. The measured S-parameters are shown in Figure4. The NF is measured at 2 dB, which is slightly higher thansimulation. This is due to slight reduction of measured power gainwhen compared with simulation.Four gain modes (maximum, medium, attenuation, and mini-mum) are realized by turning ON/OFF the bias VGS main for Mmand VGain ctrl for Msteer as aforementioned. In each gain mode,smooth gain tuning is achieved varying VGain ctrl to adjust themount of current steering. As a result, a wide range of 36 dB gaincontrol is obtained as shown in Figure 5.In Figure 6, the measured linearity performances of the LNAadopting DS technique with and without the Rsub are provided.Two-tone test at 2.135 and 2.145 GHz shows a high linearityperformance as analyzed and expected. Though, the performanceis little lower when compared with the simulation results shown inFigure 2. Measured IIP3 is 9.1 dBm showing more than 10 dB ofimprovement when compared with the case without using Rsub.P1dB is improved slightly by 1 dB. The overall LNA consumesonly 1.9 mW, which is suitable for low power applications. Chipdie photo is shown in Figure 7 and performance is summarized inTable 1.Figure 3 Proposed high linearity variable gain LNAFigure 4 Measured S-parameters and NF of the LNAFigure 5 Measured variable gains of the LNAFigure 6 Measured IIP3 of the LNA with and without Rsub of 5 KOhmDOI 10.1002/mop MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 51, No. 5, May 2009 13875. CONCLUSIONA simple but effective technique for linearity enhancement of anLNA with variable gain control in WCDMA systems is proposed.Linearity is significantly improved when the substrate of the com-mon gate transistor is floated. Smooth and step gain controls arejointly realized by using current steering and turning ON/OFF themain transistor, respectively. As a result, a wider range of gaincontrol is achieved. The LNA is also optimized for low powerconsumption. Implemented in 0.13-m CMOS process, measure-ments show 9.1 dBm of IIP3 with an extra substrate resistance,improved by more than 10 dB. 36 dB of gain control range isobtained. S11, S22, and NF are19.5,14, and 2 dB, respectively.The LNA dissipates 1.6 mA from 1.2 V supply, and die size is 0.3mm2. The proposed LNA is well suited for high-linearity, low-power applications like WCDMA.ACKNOWLEDGMENTSThe authors would like to thank Science Foundation Ireland fortheir generous funding of the research through the Centre forTelecommunication Value-Chain Research (CTVR). This workwas supported in part by the Korea Science and EngineeringFoundation (KOSEF) through the Ministry of Science and Tech-nology (MOST).REFERENCES1. V. Aparin and L.E. Larson, Analysis and reduction of cross-modulationdistortion in CDMA receivers, IEEE Trans Microwave Theory Tech 51(2003), 1591–1602.2. Y. Ding and R. Harjani, A 18 dBm IIP3 LNA in 0.35 m CMOS,IEEE Int Solid State Circuits Conf, San Francisco, CA (2001), 162–163.3. N. Kim, V. Aparin, K. Barnett, and C. Persico, A cellular-band CDMA0.25-m CMOS LNA linearized using active post-distortion, IEEE JSolid State Circuits 41 (2006), 1530–1534.4. T.W. Kim, B. Kim, and K. Lee, Highly linear receiver front-endadopting MOSFET transconductance linearization by multiple gatedtransistors, IEEE J Solid State Circuits 39 (2004), 223–229.5. V. Aparin and L.E. Larson, Modified Derivative superpostition methodfor linearizing FET low-noise amplifiers, IEEE Trans Microwave The-ory Tech 35 (2005), 571–581.6. M.-C. Yeh, Z.-M. Tsai, R.-C. Liu, K.-Y. Lin, Y.-T. Chang, and H.Wang, Design and analysis for a miniature CMOS SPDT switch usingbody-floating technique to improve power performance, IEEE TransMicrowave Theory Tech 54 (2006), 31–39.7. Q. Li and Y.P. Zhang, CMOS T/R switch design: Towards ultra-wideband and higher frequency, IEEE J Solid State Circuits 42 (2007),563–570.© 2009 Wiley Periodicals, Inc.WIDE-BAND LOW-LOSS CPW-BASEDCOMPOSITE RIGHT/LEFT-HANDEDTRANSMISSION LINENemat Dolatsha and Mahmoud ShahabadiPhotonics Research Lab., School of ECE, Univ. of Tehran, KargarAve.North, 14395–515 Tehran, Iran; Corresponding author:n.dolatsha@ece.ut.ac.irReceived 13 September 2008ABSTRACT: In this article, a coplanar waveguide (CPW)-based com-posite right/left-handed transmission line (CRLH TL) is introduced. Thestructure is realized by parallel-plate series capacitors (C) and shuntCPW stub inductors (L). Using a symmetric configuration for the unitcells along with searching for optimum values of LC components, wereduce the insertion loss and achieve wider LH-bandwidth. For the sym-metric CRLH TL, a LH-passband extending from 1.3 to 4 GHz and aRH-passband extending from 4 to 6.5 GHz are measured. © 2009 WileyPeriodicals, Inc. Microwave Opt Technol Lett 51: 1388–1390, 2009;Published online in Wiley InterScience (www.interscience.wiley.com).DOI 10.1002/mop.24319Key words: metamaterial; composite right/left-handed (CRLH); trans-mission line (TL)1. INTRODUCTIONMaterials with simultaneously negative permittivity and perme-ability were theoretically studied by Veselago in 1967 [1]. Com-posite right/left-handed transmission lines (CRLH TLs) with anti-parallel phase and group velocities are a class of these materialsrealized by cascading series capacitors and shunt inductors. Thereare also wanted and unwanted series inductors and shunt capaci-tors which should be accounted for at higher frequencies. Somenovel devices such as phase-advance phase shifters [2] and back-ward-wave antennas [3] based on the CRLH TLs have beenreported.Figure 7 Die photo of the LNATABLE 1 Summary of the LNA PerformanceParameters MeasurementPower gain (dB) 12.3Variable gain range (dB) 24S11/S22 (dB) 14/19.5NF (dB) 2.05IIP3 and P1dB (dBm) 1 and 17 without Rsub9.1 and 16 with RsubPower dissipation (mW) 1.9Supply voltage (V) 1.2Process 0.13-m CMOS1388 MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 51, No. 5, May 2009 DOI 10.1002/mop

9.1 dBm IIP3 36 dB Gain

Controllable LNA for WCDMA in

0.13-m CMOS

http://mural.maynoothuniversity.ie/1460/1/final_version.pdf

9.1 dBm IIP3 36 dB Gain Controllable LNA for WCDMA in 0.13-m CMOS

Abstract

Similar works

Full text

Available Versions

MURAL - Maynooth University Research Archive Library