This paper deals with the seismic analysis of timber framed houses filled by stones and earth mortar using a multi-scale approach going from the cell to the wall and then to the house.  At the scale of the elementary cells, experimental results allow fitting the  parameters of a new versatile hysteretic law presented herein through the definition of  a macro-element.   Then,  at  the  scale  of  wall,  the  numerical  simulations  are  able  to predict  its  behavior  under  quasi-static  cyclic  loading  and  is  compared  to  experimental results allowing validating the macro-element model

Daudeville, L.

Grange, S.

Sieffert, Y.

Vieux-Champagne, F.

English

UPCommons. Portal del coneixement obert de la UPC

XII International Conference on Computational Plasticity. Fundamentals and ApplicationsCOMPLAS XIIE. On˜ate, D.R.J. Owen, D. Peric and B. Sua´rez (Eds)MULTI-SCALE ANALYSIS OF TIMBER FRAMEDSTRUCTURES FILLED WITH EARTH AND STONESF. VIEUX-CHAMPAGNE∗, S. GRANGE∗, Y. SIEFFERT∗,L. DAUDEVILLE∗∗ UJF-Grenoble 1, Grenoble-INP, CNRS UMR 5521, 3SR Lab, Grenoble F-38041, Francee-mail: florent.vieux-champagne@3sr-grenoble.fr, web page: http://3sr.hmg.inpg.fr/3sr/Key words: Timber framed structure, Mutli-scale, Filled, Shear walls, Finite element,Constitutive model, Stones, EarthAbstract. This paper deals with the seismic analysis of timber framed houses filled bystones and earth mortar using a multi-scale approach going from the cell to the wall andthen to the house. At the scale of the elementary cells, experimental results allow fittingthe parameters of a new versatile hysteretic law presented herein through the definitionof a macro-element. Then, at the scale of wall, the numerical simulations are able topredict its behavior under quasi-static cyclic loading and is compared to experimentalresults allowing validating the macro-element model.1 INTRODUCTIONDuring the earthquake that struck Haiti, on the 12th of January 2010, a great number ofconcrete block and reinforced concrete buildings were heavily damaged. The destructionor collapse of these buildings had a dramatic impact in terms of human life and hugeeconomical loss for the country. In urban areas as well as in rural ones traditional timberframe buildings did not suffer that much, showing an enhanced structural behaviour andexposing their inhabitants to a limited risk, thanks to their lower seismic vulnerabilityand cost (see [7]).These findings raise the issue of the very limited importance given to local architecturesby the scientific community and by those responsible for reconstruction, despite the factthat in Haiti as well as in other places, those structures have often shown highly relevantuse of technical solutions and available resources, in relation to the constraints and thepotential of the context.Within the framework of the ReparH project, supported by the French National Re-search Agency (ANR), a scientific collaboration was established between researchers in thefield of architecture (CRAterre-ENSAG) and engineering (3SR - UJF) with the Haitian1Multi-scale analysis of timber framed structures filled with earth and stones  431F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudevilleorganization GADRU, to carry out a technical and methodological reflection to supportthe development of sustainable reconstruction and vulnerability reduction strategies.(a) Traditional (SCCF NGO) (b) Built for a reconstruction project (MisereorNGO)Figure 1: rural Haitian housesIn this paper an experimental approach performed previously is now compared withtraditional timber-frame constructions (see Fig. 1) by means of multi-scale non-linearnumerical analysis.The proposed method includes numerical studies from the connections to the wall ele-mentary cell (square braced by a St Andrew cross, Fig. 4(a)), to the entire wall (Fig. 6(a))and then to the whole house. More details about this multi-scale approach are given inthe references section ([4], [8] and [9]).This multi-scale approach illustrated in Fig. 2 aims at modelling shear walls or wholebuildings with a very limited number of degrees of freedom (about 500 for the wholehouse) without losing simulation accuracy. This approach allows reducing significantlycomputational cost and computational efforts for the user to realize the mesh. In addition,the multi-scale approach is really suitable in this study because experimental data areeasily obtained at connection and cell levels. It is then possible to reproduce numericallythe behavior of cells. From this first analysis at the cell scale, hysteretic behavior of thecell is fitted correctly using a modification of the 1-D law presented herein and in [6] (seeFig. 3) as a macro-element (Fig. 4(d)).2 PRESENTATION OF THE HYSTERETIC MODEL FOR THE MACRO-ELEMENTA one dimensional constitutive model in order to build the macro-element is presentedin [1] and shown in Fig. 3. This constitutive law allows reproducing elasticity, plasticand residual strains, damage and pinching effect. The branches of the force–displacementmodel are grouped into two distinct categories and numbered from (0) to (5). A first2432F. Vieux-Champagne, S. Grange, Y. Sieffert and L. DaudevilleFigure 2: Multi-sclae approachgroup formed by branches (0) to (3) describes the behaviour under monotonic loading.The initial linear branch (0) ranges from the zero displacement up to the yield displace-ment dy. The corresponding elastic stiffness is K0. This branch is followed by branch(1), which models the non-linear phenomena in the joint up to the force peak at (d1,F1).After the force peak, branches (2) and (3) model up to the ultimate displacement du atforce Fu associated to the collapse of the joint. Fu is generally chosen null to ensure acorrect continuity of forces and prevent numerical issues. Therefore, 9 parameters de-scribe the force–displacement behaviour under monotonic loading. Branch (1) is definedusing a rational quadratic Be´zier curve and provides a strict analytical continuity of forces.A second group of branches describes the hysteresis loops which are typically observedwhen the joint undergoes a reversed loading. Starting from a previously reached looppeak (upk,Fpk), branch (4) models the non-linear elastic unloading down to a null force.A residual displacement dc = 0 is commonly observed due to prior plastic deformations.The unloading stiffness K4 is either: a) proportional to the elastic stiffness K0 of thejoint; or b) proportional to the secant stiffness Fpk/upk in order to model a stiffness de-crease with displacements of increasing amplitude. Following this unloading, loading inthe opposite direction is modelled with branch (5). The stiffness at dc between branches(4) and (5) is denoted Kc and is used as a tangent for both branches for the sake ofcontinuity. Branch (5) eventually reaches the previous loop peak (u•pk,F•pk) in the op-posite loading direction. Like the unloading stiffness K4, the reloading stiffness K5 isproportional to the elastic stiffness K0 or to the secant stiffness Fpk/upk. A second setof 4 control parameters Ci=1,...,4 governs the shape of the hysteresis loops. This allowsmodelling several mechanical behaviours, in particular, the thickness of the pinching areacan be adjusted. Parameters C1 and C2 control the unloading stiffness K4 and reload-ing stiffness K5 respectively. Parameter C3 controls the tangent stiffness Kc at location3433F. Vieux-Champagne, S. Grange, Y. Sieffert and L. DaudevilleFigure 3: Proposed force–displacement model ([6])(dc,0). Finally, parameter C4 controls the value of the residual displacement dc after thenon-linear elastic unloading. These 4 control parameters Ci=1,...,4 depend mainly on thephenomena involved, and therefore on the configuration of the modelled system. Theyare constant for a given configuration.Finally, a third set of 3 parameters controls the damage process under cyclic loadingof the model. The word damage refers here to the decrease of strength under cyclic. It isbased on the hypothesis that the hysteresis loops are bound by the backbone curve whichmodels the force–displacement evolution of the joint under monotonic loading. During thefirst loading, the peak (upk,Fpk) is located on the backbone curve. The damage processdefines the evolution of the ratio (1-D) between the “non-damaged load” Fmono and the“damaged load” Fpk. The scalar damage indicator D ranges from 0 to 1, where D = 0corresponds to a non-damaged mechanical system and D = 1 corresponds to a fullycollapsed mechanical system. D is increased of ∆D at each change of the force sign ((4)to (5) in Figure 3). To ensure the damage stabilization after a few cycles of constantamplitude as experimentally observed, an upper limit D∞ for the displacement dmax isdefined, using a power law (eq 1). A power term Br > 1 ensures that the damage remainsmoderate before the force peak and becomes heavy after the peak.D∞ = Bc (dmax/d1)Br (1)4434F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudeville3 CELL’S SCALE - FITTING PARAMETERSIn this part, the elementary cell is described and the macro-element is defined. Then,the calibration of this simplified element is presented with the corresponding parametersof the law.3.1 Structure and simplified FE modelThe elementary cell shown in Fig. 4(a) is made of four wood beams connected togetherby punched steel strip nailed by 3 mm×70 mm common nails (see Fig. 4(b)). It is bracedby wood bars X-crossed and filled with a stone masonry and an earth mortar. It can benoted that X-cross is not symmetric. One of these bar goes from the top to the bottomwhereas the second one is split in two parts and linked to the first one at the middle ofthe cell. More properties of this structure are given in the fourth part.The cell is designed to be as close as possible of the wall’s part represented in Fig. 6(a).Nevertheless the boundary conditions are not exactly the same due to practices issues.The upper and the bottom part of the cell, made with type 1-joint (see Fig. 4(b)), matchwith the same parts of the wall. Therefore, the middle part of the wall, made withtype 2-joint (see Fig. 4(c)), is not included in the elementary cell.(a) Elementary cellNAIL( 3 X 70 mm)VERTICAL POST( 50 X 100 mm)STRIP( 1.5 X 30 mm)HORIZONTAL BAND( 50 X 100 mm)(b) Type 1-joint (c) Type 2-joint(d) Macro-element ofthe cellFigure 4: Cell – Experimental and modellingThe experimental campaign on elementary cell involved two reversed cyclics and onemonotonic quasi-static tests per configuration. The influence of the kind and the presenceof filling and bracing were tested but these experiments are not presented herein. Theloading was applied on top beam of the structure.The macro-element, simplified FE model, shown in Fig. 4(d)) is composed of 4 barswhere the right upper node is linked with left bottom node with the 1D non linear consti-tutive law presented above. This representation allow concentrating all the non-linearitiesof the cell in one global element. It ensures the hypothesis of a parallelogram-like deforma-tion of the cell, therefore modelling only the shearing behaviour (i.e. in and out-of-planebending and overturning effects are not taken into account). This hypothesis is based onprevious studies [5] and experimental observations.5435F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudeville−80 −60 −40 −20 0 20 40 60 80−15−10−5051015displacement (mm)load (kN) numeric − fitting law experimentalK0 1.7e6 N/mdy 5.0e-4 md1 3.8e-2 mF1 1.3e4 NK1 1.5e5 N/md2 6.0e-2 mF2 1.0e4 Ndu 8.0e-2 mFu 7.5e4 NC1 -1.0C2 -1.0C3 1.0e-1C4 8.0e-1Bc 1.2e-1Br 2.0η 5.0e-1Figure 5: Calibration of the model on an experimental test and the model’s parameters3.2 Calibration of the parameters at the cell’s levelThe law is implemented in AGALab, a finite element code developed in MatlabR© by3SR teamThe results of the tests performed on the cells are used to calibrate the constitutivemodel. The calibration consists in reproducing one particular test as displayed in Fig. 5.Normally, it is obtained by calculating the backbone curve parameters from monotonictest(s) and by calibrating the pinching and damage parameters from cyclic test(s). Herein,only one cyclic test is used to fit the parameters because the difference between the back-bone curve and the envelop curve of a cycle test is very low and because the repeatabilityof the cycle tests is good.The coefficients are the same in both positive and negative directions which lead to asymmetric numerical curve. Therefore only the positive parameters used to the calibrationare given in the table of the figure 5.Nevertheless, it can be noted an asymmetry of the experimental curve which can beexplained by the difference between the continuous plank and the perpendicular two partsof the X-cross. When the cell’s diagonal made of two bars is under a compressive strength,the stiffness is lower as shown in the graph of Fig. 5 (negative displacement). That’s whythe calibration has been done only on the positive side of the experimental curve.4 WALL’S SCALE - PREDICTION OF ITS GLOBAL BEHAVIORIn this part, the structure of the wall is described. Then, a mesh of the wall using anassociation of the macro-element is presented. Finally a prediction of the wall’s behaviourunder quasi-static loading given by the model is compared with an experimental test.6436F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudeville4.1 Structure and modellingThe structure of the wall is displayed on Fig. 6(a). It is 1.975 meter high and 3.75meters wide. It is composed of two 10 cm × 10 cm posts at both extremities and three5 cm× 10 cm in the center. They are linked with a bottom and an upper 5 cm× 10 cmwood beam by the mean of punched steel strip FP30/1,5/50 from Simpson Strong-TieR©,30 mm wide and 1, 5 mm thick. 3 mm×70 mm common steel wire nails are used (see [2])to fixed the strip. Timber strength class is C18 with a density ρmean = 380 kg/m3according to the European standard EN 338 (see [3]).The experimental campaign has been realised at the CNR-Ivalsa in Trento, Italy, wherethree filled wall were tested : two cycle tests and one monotonic.Type 2-jointType 1-jointCell(a) Wall filled with stones and earth mortar (b) Test machineFigure 6: A wall and the test machineThe mesh of the wall using the association of the macro-elements is described in Fig. 7.Kinematic links in both directions of the different nodes at the interface of the macro-elements are also presented.kkkkkkkky-axis kinematic linkyxx-axis kinematic linkFigure 7: Mesh of the wall using an association of macro-element7437F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudeville4.2 Comparison between numerical and experimental resultsThe prediction of the wall’s behavior is provided in Fig. 8. Regarding the resistingforce prediction, the model shows good results with only 11% of error. The differencecan be explained by the fact that the type 2-joints energy dissipation is not taken intoaccount.−80 −60 −40 −20 0 20 40 60 80−50−40−30−20−1001020304050displacement (mm)load (kN) modeling experimentalFigure 8: Prediction of the wall’s behavior – Experimental versus numerical resultsThen, it can be noticed that the wall model cannot predict softening due to damageeffect appearing for top displacements of about 40 mm. In the numerical results, thesoftening appears for top displacements of about 80 mm when using the parametersfitted at the cell’s level.Ongoing research aims at adding supplementary features to be able to take into accountthe type 2-connection and the damage effect.The computation effort to implement the model and the computational cost are low.Therefore in comparison with the simplicity of the model, the prediction is satisfactoryand validates this simplified approach.5 CONCLUSIONSThis paper presents a simplified finite element analysis study about traditional woodstructure filled with stones and an earth mortar. The first part describes the constitutivelaw allowing to accurately reproduce the hysteretic behavior, damage and pinching effect.Then, application of this law is illustrated in a multi-scale study by reproducing theexperimental behavior of a cell under quasi-static loading in order to build a macro-element. The third part presents the prediction of the experimental wall’s behavior bymean of a simplified FE model composed of the macro-element’s association. This multi-scale approach is very simple and allow to predict the behavior of timber frame wall filled8438F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudevillewith stones and earth mortar.Ongoing research aims to model the the whole house by using only 500 degree offreedoms using the same macro-element as shown on Fig.9. An experimental test onan uni-axial shaking table at the house’s scale was performed at the FCBA, Bordeaux inApril 2013 and will allow to validate at the third scale to validate the multi-scale approachpresented herein.Figure 9: Modelling of a whole house with the macro-element6 ACKNOWLEGMENTThe french agency ANR is gratefully acknowledged for funding this research ANR-10-HAIT-003.Philippe Garnier is also acknowledged for the management of this project.References[1] C. Boudaud, J. Baroth, S. Hameury, and L. Daudeville. Multi-scale modelling of timber-framestructures under seismic loading. XII International Conference on Computational Plasticity, 2013.[2] EN 10230-1. Steel Wire Nails - Part 1: Loose Nails For General Applications, 2000.[3] EN 338. Structural timber - Strength classes, 2003.[4] B. Folz and A. Filiatrault. Cyclic analysis of wood shear walls. Journal of Structural Engineering,127(4), pp 433-441, 2001.[5] A.K. Gupta and G.P. Kuo. Behavior wood-framed shear walls. Journal of Structural Engineering,111(8), 1722-1733, 1985.[6] J. Humbert. Characterization of the behavior of timber structures with metal fasteners undergoingseismic loadings. PhD thesis, Grenoble University, 2010.9439F. Vieux-Champagne, S. Grange, Y. Sieffert and L. Daudeville[7] R. Langenbach. ”crosswalls” instead of shearwalls. 5th National Conference on Earthquake Engineer-ing, 2003.[8] N. Richard. Approche multi-e´chelles pour la mode´lisation de structures en bois sous sollicitations sis-miques. PhD thesis, Ecole Normale Supe´rieure de Cachan, Laboratoire de Me´canique et Technologie,2001.[9] J. Xu and J.D. Dolan. Development of a wood-frame shear wall model in abaqus. Journal of structuralengineering, 135(8), 977-984, 2009.10440

Multi-scale analysis of timber framed structures filled with earth and stones

Hal - Université Grenoble Alpes

UPCommons

https://upcommons.upc.edu/bitstream/2117/182580/1/COMPLAS2013-39_Multi-scale%20analysis%20of%20timber.pdf

Multi-scale analysis of timber framed structures filled with earth and stones

Abstract

Similar works

Full text

Available Versions

UPCommons. Portal del coneixement obert de la UPC

Hal - Université Grenoble Alpes

UPCommons