Sekulic, Sava

English

Periodica Polytechnica (Budapest University of Technology and Economics)

INVESTIGATION OF TANGENTIAL FORCES IN METAL CUTTING BY DIMENSIONAL ANALYSIS* By S. S. SEKULIC Department of Metal Cutting, University of Novi Sad (Received February 12, 1976) Presented by Prof. Dr. I. KAL_'\'SZI, Department of Machine Production Technology, Technical University, Budapest 1. Introduction Determination of the tangential tool force for different types of metal cutting processes is one of the basic goals from practical as well as theoretical point of view. Forces wich arise during cutting are transmitted hy the tool to the machine. Knowledge of the tangential tool force permits to determine the defor-mation of work piece and thus the tolerance of machining. Knowing the tan-gential tool force one can also determine the right dimensions of the tool as well as the dimensions of certain parts of the machine. Since the end of the last century there havc been various attempts to theoretically determine tangential tool force, starting from the basic assump-tions of the classical mechanics. These models gave formulas for the determi-nation of tangential tool force in terms of properties of the material of work piece. Great many equations were derived from mechanical models, hut in general, the values of the tangential tool force calculated by different equations differed significantly. We refer to some of the most famous research works in this field: 1. A .. TIME (1870), TREsKA (1873), AFANASJEV (1883), GAUSNER (1892), ZVORIKIN (1893), BRIKS (1896), l\IERCHA);T (1942), HUKS (1951), LOLADZE (1952), KRoNENBERG (1957). From the early twenties, a great many force measuring devices have heen developed up to now, hased on different (mechanical, hydraulic aI, pneumatical, inductive, with strain gauges, piezoelectric, etc.) principles. Results indicate that the models hased on the classical mechanics are too simplified (e.g., they greatly simplify complex process of cutting) to ohtain agreement between calculated and measured values for the tangcntial tool force. * Common research by both Departments of University of Novi Sad and Technical University, Budapest 156 S. S. SEKULfC Therefore, most tangential tool force equations used today are based on graphoanalytical records. The formula given by Kronenberg is usually applied for tangential tool force as a function of chip cross section A = ()s: (1) Extending this formula (1) (2) where C~ and Ck, depend hoth on the material of work piece, on the tool, and on the tool's rake angle 7': Xl and)'l and £Ok depend on the material of work piece alone. In the thirties, attempts were made to determine tangential tool force according to the plastic properties of material. However, just as for mechanical models, the agreement hetween measured and calculated values of the tangen-tial tool force was rather poor. This led to the conclusion that also this analysis ignored many important factors. Important works in this field are those hy REJTO (1926) [1], KUZNECOV (1941) [2], KRIVOUHOV (1944) [6]. Now the polytropic law, valid in the plastic region, will be applied to determine the compression stresses in a chip. This law is valid for the compres-sion of cylindrical and prismatic specimens (with square cross section) and with different slenderness ratios of height ho to diameter of the unloaded spec-imen. Equation of the polytropic compression is Fohr;' = Fh = C = const. (3) where F 0 is the force at the beginning of plastic compression referred to the initial height of the specimen h[)' F is the force referred to the actual height of the specimen ho > h. and m is the exponent of thc polytropic change: 111 f (~\. h I According to Kuznecov, tangential tool force can he determined directly from the polytropic compression law. Solving Eq. (3) for F yields the force during plastic compression: F= Fol- . . It )m l ho (4) Force at the beginning of plastic compression F 0 can he expressed as TANGETIAL FORCES 11', METAL CUTTING 157 where Go is the yield stress and Ao = ab the initial cross section of the speci-men. Substituting (4) we get (5) Identifying the process of specimen compression in the plastic range with that of the chip (i.e. identifying with the cross section of the chip ab, where a is the thickness and b the width of the chip and ratio ho/h with the chip's compression factor I. = ho(h)) we get for the tangential tool force: Using the polytropic law for compression in case of turning, Krivouhoy gets a more complicated formula for the tangential tool force SI.m R 'I Fl = ( ~ (I. - l)(m -~-1) (6) where R = Dj2 is the outer radius of work piece and b is the depth of cut. For R = =, i.e. in the case of machining a flat plane, the last expression becomes undetermined and equals 0.=. This equation is a special case of L'Hospital's rule. If higher accuracy is needed, dynamometry methods are more efficient. In this work wc use dimensional analysis as a function of the primary factors, while the other effects are involved in an empirical coefficient. So far, dimensional analysis has been applied in two cases, to determine the tempera-tnre of tool and the relationship between tool life and cutting speed. 2. Application of dimensional analysis to tangential tool force Experiments showed tangential tool forces to depend on the stress of plastic compression in chip a, the chip cross section a = OS, depth of cut 0 and feed s, hence, Fl f(b, G, s) . Expanding this function to series of the type Fl = ~ Aiax O-V SZ the following condition must be satisfied (7) (8) (9) 158 S. s. SEKr:LIC The basic quantities needed for the application of the dimensional ana-lysis are known to be: (L] - length [M] = mass [S] time [F] [L1VIS-2] force [a] L-IMS-2] stress [0] [L] depth of cut [s] = [L] feed. Substituting these values in Eq. (9): writing yields 1 1 2 x+y+:;l x I 2x x=1 z=2 Substituting (12) into (8) we get FI S Ai aY s(Z-y) or Introducing the coefficient g = bjs: From (15): be f(g) = B the expression for tangential tool foree will take the form FI = Ba S2; B = f(g)· (10) (11) (12) (13) (14) (15) (16) By analyzing the last expression, we conclude that the value of the tangential tool force depends on the plastic properties of the cut material, i.e. on the com-pression stress in the cross section of the chip. To determine tangential tool force from (16) we have to know the compres-sion stress a in the chip and the empirical relationship B = f (g) TANGETIAL FORCES IS .\fETAL CUTTI;\-G 159 (in graphical or analytical form), which corresponds to the actual working conditions, and which can be obtained experimentally. The value of the compression stress in the chip, as already mentioned, could be obtained from the polytropic law, to be used for two alternatives of deriving the tangential tool force for the work on lathe. 2.1. First alternative of the expression for tangential tool force According to the physical law of constant volume before and after com-pression in the plastic range: Vo = A 0 h 0 = V = Ah (17) or (18) The factor of compression j. is the ratio of the cross sections or of the height values of the specimen after and hefore compression. From (3) we have (19) so that multiplying the left side of equation hy (20) Equalizing the right sides of Eqs (19) and (20) yields for the stress of compression in the plastic range: (J = (J 0 l.m - 1 (21) Identifying the stress of plastic compression with the stress in the chip and substituting (21) in (16): (22) we get Fl B =---=---(J 0 l.m - 1 S2 f(g) , 160 S. S. SEKULIC an empirical relationship. If this relationship B = f (g) is known for the material of the work piece, then For given conditions of cutting we may perform a short experiment and determine ). from the expression , Cs 1.=--Os y1s (23) where Cs is the weight, Is the length and y the specific weight of the chip. Assume m = 1.25 is the exponent of the polytropic change (the value recommended by Kuznecov for steel), then all the necessary elements for the calculation of tangential tool force for cutting steel materials are known. It is important to note that B f (g) depends on the working conditions, mainly on the tool geometry as well as on the lubrication and cooling of the system. 2.2 Second alternative for deriving the expression of tangential tool force The equation of the polytropic change (3) divided by the cross section area corresponding to the height h of the specimen gives: Since the volume of the specimen before compression is (17) we have v= Ah V A=-. It Substituting (25) into (24) and solving for (J, we get where C Cl = - = const . V (24) (25) (26) TAXGETIAL FORCES IX JIETAL CtTTI.YG 161 But, for side machining on the lathe, the length of chip element, for a given depth of cut 6 and given approach angle of a tool % is proportional to the feed s. i.e. Therefore, resubstituting (27) into (26) where Bl = Cl Ci- m = const. Substituting (28) into (16) const. (27) (28) (29) where BBI = B2 = f(g). Since B = f(g) and BI = cons!" from (29) it follows that (30) Assume B2 to be proportional to the slenderness ratio of a chip g: (31) where Bo = const., yields tangential tool force (32) Substituting the slenderness ratio into (32): (33) Be (as in alternative 1) the exponent of the polytropic change m = 1.25, which corresponds to the steel, we shall finally get for the tangential tool force for machining on lathe B6s lJ,75. (34) Comparing Eqs (33) and (2), this latter ohtained by graphoanalytical method (from measured data) where the exponents x = 1.00 and y = 0.75 represent the average values for steeL they are seen to represent identical for-mulas, even identical numerical values. Constant B 0 is equivalent to the specif-ic tangential tool force ChI' In the tangential tool force equation, compression stress a may be substituted for some other quantities with the same dimension and still pre-serve dimensional identity. Using shear stress T s in the plane of shear instead 162 of (J in the equation, we get S. S. SEKFLIC b B=f(g);g=-· 5 (35) Mechanical experiment involved the following shear stress/strain rela-tionship: T = T1 em. Extrapolation of the above relationship to the range of high deforma-tions which corresponds to cntting (cs = 2.5) yields stresses close to the stress in the plane of shear T s: where T1 = T.=1 and m is the slope in log-log scale. The shear stress in the plane of shear can be approximated as: 0.6 (JAr 1-1.71p (36) (37) instead of the relationship T = f(e), "where (JM is the tensile strength of the material and 1p its contraction. Substituting (36) into (35) we get for the tangential fool force (38) so that (39) which may be determined experimentally. From the approximate value of the shear stress in the plane of shear, the tangential tool force is, substituting (37) into (35): where. F1= B~aM 52 1-1.71p B = 1-1.71fJ;\\ 0.6 a F . _1 =f(g) 52 (40) (41) with the same dependence as in the previous case. Consequently, tangential tool force can be determined from the mechanical characteristics of the ma-terial and B = f (g). TANCETIAL FORCES IN METAL CUTTIi,G 163 3. Conclusiou From the expression of the first alternative the determination of the tangential tool force on the lathe is seen to depend on the knowledge of ma-terial yield point (J 0 = (J 0.2 to be determined by mechanical tests. Chip compres-sion factor ). as a measure of the plastic deformation may be determined by a short cutting experiment. Finally, dependence of the coefficient B on the slenderness of chip must also be determined experimentally. We note that ). and B = f (g) depend on the actual working conditions, tool geometry, etc. Comparing the first alternative equation for tangential tool force (22) to that by KUZNECOV they are seen to differ considerably, although they both use the polytropic law for compression in the plastic range. It is clear that the first expression obtained by dimensional analysis is more complete, because it includes function B = f (g), taking into account actual working conditions. The second alternative equation for tangential tool force that led to the well-known extended formula shows that the use of the polytropic law of compression is correct for cutting problems. Actually, starting assumptions in both are the same. Because expanded formula for the determination of the tangential tool force is obtained from the graphoanalytic method (based on tangential tool force records), the second alternative derivation seems to proY(- that assump-tions in the first one were correct, making an experimental proof of the first alternatiye needless. Last but not least, the general tangential tool force equation B = f(g) obtained by dimensional analysis giyes wide possibilities for process analysis. 'For example, by substituting the compressh-e stress (J for the stress in the plane of shear T s one may get conyenient formulas for the determination of tangential tool force on the lathe. Summary Dimensional analysis is convenient for determining the tangential tool force. taking into consideration the primary effects on tool force (stresse5 in the chip. depth of cut and feed). Some possible uses of the obtained equations are presented. For example, replacing the stress in equations obtained by dimensional analysis by stresses measured in other way (substituting the shear stress in the plane of shear)_ relationships suitable for further research "ill result. 6 Periodica Polytechnic-a ~1. 20/2. 164 S. S. SEKULIC References 1. REJTO, S.: Fundamentals of Theoretical Mechanical Technology, and Technology of Metals. Vol. II*. J. Nemeth, Budapest, 1919. (in Hungarian) 2. KUZNECOV, W. D.: Fisika tverdogo tela. T. Ill. Tomsk 1944. 3. STANKOVH\ P.: Masinska obrada, I knjiga, trece izdanje, Gradjevinska knjiga. Beograd, 1967. 4. REZl'I"IKOV, N. 1.: Uchenie 0 rezanii metallov, Mashgiz, Moskva, 1947. 5. GRANOVSKIY, G. 1.: Rezanie metallov, Mashgiz, Moskva, 1954. 6. KRIVOUHOV, A. A.: Obrabotka metallov rezaniem, Oborongiz, Moskva, 1958. 7. ZDENKOVIC, R.: Obrada metala skidanjem, Sveuciliste u Zagrebu, Zagreb, 1965. 8. KRONENBERG, M.: Grundziige der Zerspanungslehre, Springer Verlag, Berlin, 1954. 9. KRONENBERG, M.: Machining Science and Application, Pergamon Press, Oxford, 1966. 10. ZOREV, N. N.: Raschot proekciy sili rezaniya, Mashgiz, Moskva, 1958. Prof. Sava SEKULIC, Dept. of Metal Cutting, University of Novi Sad, Yugoslavia. 21000 Novi Sad, Fruskogorska 19. 

INVESTIGATION OF TANGENTIAL FORCES IN METAL CUTTING BY DIMENSIONAL ANALYSIS

https://pp.bme.hu/me/article/download/5944/5049

INVESTIGATION OF TANGENTIAL FORCES IN METAL CUTTING BY DIMENSIONAL ANALYSIS

Abstract

Similar works

Full text

Available Versions

Periodica Polytechnica (Budapest University of Technology and Economics)