The paper presents concept of design and realization of the new class of printed antenna structures which consist of a linear axial array of dipoles, subreflector, feed network and a bal-un, all printed on a common dielectric substrate. The array is positioned on the axis focus of the cylindrical-parabolic reflector. Use of the reflector enables reducing back side radiation and shaping beamwidth in H-plane thus obtaining higher gain while the printed subreflector gives the possibility of achieving additional gain. Besides, by using dipoles with pentagonal shape that operate on the second resonance, enhanced bandwidth of the array has been accomplished. Four variants of such arrays have been realized: two of them with 8 radiating elements for the frequency range around 26 GHz - one with uniform and the other with tapered feed distribution, featuring gains of 27.5 dBi and 25.7 dBi, respectively. The latter has the side lobe suppression of 28 dB in E-plane. Two other arrays that are intended for ranges around 23 GHz and 60 GHz have 16 radiating elements, uniform feed distribution and measured gains of 33 dBi and 34 dBi, respectively. Bandwidths of all realized model for S11 less than -10 dB is around 30 %. In all cases agreement between simulated and measured results is very good

Nešić, Aleksandar

Radnovic, Ivana

Milijic, Marija

Micic, Zoran

Nešić, Dušan

Informacije MIDEM - Journal of Microelectronics Electronic Components and Materials

Central Repository of the Institute of Chemistry, Technology and Metallurgy (CER)

97Original scientific paper MIDEM SocietyJournal of Microelectronics, Electronic Components and MaterialsVol. 43, No. 2(2013), 97 – 102Cylindrical-parabolic reflector with printed  antenna structuresAleksandar Nešić1, Ivana Radnović1, Marija Milijic2, Zoran Mićić1 and Dusan Nešić31Institute IMTEL Komunikacije a.d, New Belgrade, Serbia2Faculty of Electronic Engineering, University of Nis, Nis, Serbia3IHTM-CMTM, University of Belgrade, Belgrade, SerbiaAbstract: The paper presents concept of design and realization of the new class of printed antenna structures which consist of a linear axial array of dipoles, subreflector, feed network and a bal-un, all printed on a common dielectric substrate. The array is positioned on the axis focus of the cylindrical-parabolic reflector. Use of the reflector enables reducing back side radiation and shaping beamwidth in H-plane thus obtaining higher gain while the printed subreflector gives the possibility of achieving additional gain.  Besides, by using dipoles with pentagonal shape that operate on the second resonance, enhanced bandwidth of the array has been accomplished. Four variants of such arrays have been realized: two of them with 8 radiating elements for the frequency range around 26 GHz – one with uniform and the other with tapered feed distribution, featuring gains of 27.5 dBi and 25.7 dBi, respectively. The latter has the side lobe suppression of 28 dB in E-plane. Two other arrays that are intended for ranges around 23 GHz and 60 GHz have 16 radiating elements, uniform feed distribution and measured gains of 33 dBi and 34 dBi, respectively. Bandwidths of all realized model for S11 less than -10 dB is around 30 %. In all cases agreement between simulated and measured results is very good.  Key words: Microwaves and millimeter waves, Antenna array, Printed antenna, Cylindrical-parabolic reflectorCilindrično parabolični odbojniki s tiskanimi antenamPovzetek: Članek predstavlja koncept dizajna in realizacijo nove tiskane antene, ki je sestavljena z linearno matriko dipolov, odbojnikom in napajalnim omrežjem na skupnem dielektričnem substratu. Niz je nameščen v žariščni osi cilindričnega paraboličnega odbojnika. Uporaba odbojnika omogoča znižanje sevanja nazaj in oblikovanje pasovne širine v ravnini H za doseganje večjega ojačenja Uporaba dipolov v obliki peterokotnika in delovanju v drugi resonančni frekvenci omogoča povečanje pasovne širine. Realizirane so štiri inačice teh matrik. V vseh primerih je bilo doseženo dobro ujemanje med simulacijami in meritvami.Ključne besede: mikrovalovi in milimeterski valovi, matrična antenna, tiskana antenna cilindričen paraboličen odbojnik* Corresponding Author’s e-mail: nesicad@nanosys.ihtm.bg.ac.rs1 IntroductionIn the last two decades printed antenna structures are dominant over conventional antennas especially in mi-crowave and millimeter wave ranges, except in some specific applications. They are practically indispensable in the field of reconfigurable antennas. Main advantag-es of printed antenna structures are: high reproducibil-ity, small dimensions, low weight, compactness, beam scanning possibility as well as possibility of integration with passive and active microwave circuits.However, there are applications where printed anten-nas show certain disadvantages such as: applications in high power transmitters (possibility of dielectric break-down), applications in high gain antennas (due to rela-tively high losses in printed feed lines) and in antennas with very high side lobe suppression (over 40 dB) due to critical dimension tolerances. In order to overcome these significant disadvantages, the concept of linear axial antenna array positioned on a focal axis of a cylindrical-parabolic reflector is intro-duced [1-4].As radiating elements in the antenna array printed di-poles of pentagonal shape operating on the second resonance are used. In this way a much wider band-98width than with conventional printed antenna arrays is obtained. The presence of the cylindrical-parabolic reflector in-troduces a third dimension in a standard planar struc-ture, and this is practically the only drawback compar-ing to conventional printed antenna arrays. However, by applying a subreflector which consists of two strips printed on both sides of the dielectric substrate, the depth of the cylindrical-parabolic reflector can be re-duced and so the overall size of the antenna structure decreased.Differently from Cassegrain antennas where subreflec-tor covers the central part of the antenna aperture re-sulting in lower efficiency and side lobe suppression, the effect of aperture blockage is negligible in pre-sented concept. Moreover, owing to the subreflector, more suitable illumination distribution, i.e. higher gain and better side lobe suppression in H-plane can be achieved.2 Concept2.1 Radiating ElementsRadiating elements in the array are printed pentago-nally shaped dipoles. One half of dipoles is printed on one side of the dielectric substrate and their other half on the opposite substrate side, Fig.1, [5]. These dipoles operate on the second resonance (antiresonance) ena-bling much slower impedance variation with frequen-cy than in case of operation on the first resonance. The dipole impedance can range from about 70 W to a few hundred ohms. Variations of real and imaginary parts of the pentagonal dipole impedance with frequency are shown in Fig. 2. The dipole is optimized to imped-ance around (100 + j0) W at the central frequency of 26  GHz. Relative dielectric constant (er) and thickness (h) of the substrate the dipole is printed on are 2.1 and 0.254 mm (CuFlon), respectively. Impedance variation with frequency in such dipoles is a few dozen times smaller than in patches which are the most common conventional printed radiating elements. Bandwidth of the single dipole (VSWR < 2) is around 30 %. Figure 2: Real and imaginary parts of the pentagonal dipole impedance* as a function of frequency (er=2.1, h =0.254 mm, S**= λ/4).*The dipole impedance is optimized to obtain (100+j0) W at 26 GHz. **S – distance between dipole axis and the flat reflec-tor.2.2 Axial Array of DipolesAn axial array of dipoles has been formed, Fig. 3. Mutual impedances of these dipoles are relatively small which makes the design of the array significantly simpler which is especially important in cases of beam scan-ning. Certainly, the number of radiating elements in the array depends on the required E-field beamwidth. Distance between adjacent dipoles is practically a com-promise between the gain and the sufficient suppres-sion of grating lobes. The distance between dipoles in axial antenna arrays with tapered feed distribution is chosen to be around 0.85 λ in order to obtain relatively high array gain and grating lobe level that is lower than the highest (usually the first) side lobe level, [6] (which is 13 dB suppressed with regard to the main lobe in case of uniform distri-bution). 2.3 Printed SubreflectorIn front of the array of dipoles positioned on the fo-cal axis of the cylindrical-parabolic reflector, there are strips printed on both sides of the substrate playing the role of a subreflector, Fig. 3, Fig. 5. Subreflector’s axis and longitudinal axis of the dipoles’ array are spaced λ/4 apart at the central frequency. Use of the subre-A. Nešić et al; Informacije Midem, Vol. 43, No. 2(2013), 97 – 102Figure 1: Printed pentagonal dipole as a basic element of the antenna array.99flector offers the possibility of decreasing the depth of the cylindrical-parabolic reflector, i.e. of lowering the ratio Lf/D, where Lf is the focal length of the reflector and D is its width. Aperture blockage of the antenna structure by this subreflector is almost negligible due to extremely small thickness of the dielectric substrate (around λ/100). By varying width of the subreflector strip one can optimize illumination distribution of the cylindrical-parabolic reflector and obtain higher gain.Figure 3: Printed antenna array with the subreflector and the feed network integrated on the same dielectric substrate.2.4 Transition to Coaxial Connector or to Rectan-gular WaveguideComplete feed network is realized in symmetrical (bal-anced) microstrip lines. In order to link a symmetrical to an asymmetrical (conventional) structure, a tapered symmetrical to asymmetrical microstrip transition (BAL-UN) is used in ranges below 40 GHz, Fig. 3(a). Its asymmetrical end is terminated with a coaxial SMA connector. However, in frequency ranges above 40 GHz there is a need for symmetrical microstrip-to-rectangu-lar waveguide transition, [7]. Design of this transition is based on gradually tapering lines of a symmetrical microstrip that enters into waveguide and forming ridges at opposite sides of a dielectric substrate, Fig. 3. Through these ridges the E-field vector is being con-centrated and rotated by 90° becoming parallel to shorter sides of a rectangular waveguide. 2.5 Cylindrical-Parabolic ReflektorCylindrical-parabolic reflector is made of a relatively thin aluminum (2  mm). It consists of two halves that are attached to each other along their apexes and fas-tened by screws or clasps. Holes through which symmetri-cal microstrip lines of the feed network pass are drilled through the junction of the two reflector’s halves. Di-ameter (d) of these holes is chosen to be d>3W, where W is width of the symmetrical microstrip feed line, Fig 4. In this way the influence of the holes’ rims on the feed line is being eliminated.Ratio Lf/D (Lf – focal length of the reflector, D – width of the reflector) equals 0.2 in realized antennas while the length of the reflector (L) depends on the length of the axial array.Figure 4: Holes in the cylindrical-parabolic reflector through which microstrip lines of the feed network pass.2.6 Feed NetworkFeed network is realized in symmetrical microstrip mainly for these reasons:-  Radiating elements are dipoles whose halves are printed on the opposite sides of the dielectric substrate thus representing a typical symmetrical structure.-  Feed networks in printed antenna structures are the main source of losses due to loss in feed lines. Symmetrical microstrip structure by its nature has lower losses than a conventional asymmetrical microstrip. In realized antenna models with uniform feed distri-bution tapered impedance transformers are used in branching lines of the feed network, as shown in Fig 3. In case of antennas with high side lobe suppression we applied quarter-wave impedance transformers with suitable transformation ratio enabling desired tapered distribution, Fig 5. Figure 5: Example of feed network with impedance transformers (T1-4, Ta-b) for tapered distribution (detail in the left lower corner).A. Nešić et al; Informacije Midem, Vol. 43, No. 2(2013), 97 – 102100Symmetrical microstrip feed networks are terminated either with symmetrical-to-asymmetrical microstrip transition or with symmetrical microstrip-to-wave-guide transition, both described in the subchapter 2.4.3 RealizationsOn the basis of new design concept and by use of WIPL-D software package [8] for simulations four models of printed antenna arrays in the cylindrical-parabolic re-flector have been developed:(A) Array with 8 radiating elements operating at 26 GHz range with uniform feed distribution,(B) Array with 8 radiating elements operating at 26 GHz range with tapered feed distribution,(C) Array with 16 radiating elements operating at 23 GHz range with uniform feed distribution, and(D) Array with 16 radiating elements operating at 60 GHz range with uniform feed distribution.Their main technical and measured electrical charac-teristics are given in Table 1 while the photographs of the realized models are shown in Figures 6 - 9. From the obtained results we can come to a conclusion that practically all relevant parameters of this class of antenna arrays (bandwidth, gain, aperture efficiency) are significantly better than those of conventional printed antenna arrays. Table 1Array (A) Array (B) Array (C) Array (D)Number of radiating elements 8 8 16 16Feed distribution Uniform Tapered Uniform UniformDielectric substrate CuFlon(εr=2.1, h=0.254 mm, tanδ=4x10-4)CuFlon(εr=2.1, h=0.254 mm, tanδ=4x10-4)CuFlon(εr=2.1, h=0.254 mm, tanδ=4x10-4)CuFlon(εr=2.1, h=0.127 mm, tanδ=4x10-4)Dipoles’ impedances ~(100+j0) Ω ~(100+j0) Ω ~(100+j0) Ω ~(100+j0) ΩDistance between dipoles 11 mm (0.95 λ, 26 GHz)10 mm (0.85 λ, 26 GHz)14 mm (1.07 λ, 23 GHz)5.5 mm (1.1 λ, 60 GHz)Width of the subreflector 1.7 mm 1.7 mm 3.1 mm 0.866 mmDimensions of the cylindrical-parabolic reflectorL (Length) 110 mm 110 mm 250 mm 100 mmD (Width) 100 mm 100 mm 200 mm 100 mmLength of the BAL-UN/sym. mstrip to waveguide transition (case D)8 mm 8 mm 8 mm 5.09 mmType of connector SMA SMA SMA waveguide WR-15Measured gain at the central frequency ~27.5 dBi (@26 GHz)~25.7 dBi(@26 GHz)~33 dBi(@23 GHz)~34 dBi(@60 GHz)FSLSE* (measured) FSLSH* (measured) ~13 dB ~20 dB ~28 dB ~22 dB ~13 dB ~14 dB ~13 dB ~17 dBBandwidth (VSWR<2) (24.5-28.0) GHz (24.2-29.2) GHz (18-28) GHz (57.5-75.0) GHzAperture efficiency 54.1% 35.8% 54.2% 54.2%Losses in metallization and dielectric ~1.1 dB ~1.1 dB ~2.2 dB near 3 dBmaximum handling power, theory/real ~67 W / 33 W ~67 W / 33 W ~67 W / 33 W ~20 W / 10 WFSLSE*, FSLSH* - First Side Lobe Suppression in E- and H-planeFigure 6: Photograph of the realized 26 GHz antenna array (A) in the cylindrical-parabolic reflector with uni-form feed distribution.A. Nešić et al; Informacije Midem, Vol. 43, No. 2(2013), 97 – 102101Maximum working temperature for CuFlon is 1750C, 1500C above normal temperature of 250C. Substrate CuFlon is a soft substrate with low thermal conductiv-ity, 0.25 W/m/0C, comparing to high thermal conductiv-ity silicon [11].Figure 7: Photograph of the realized 26 GHz antenna array (B) in the cylindrical-parabolic reflector with ta-pered feed distribution with the detail of the tapered feed network.Figure 8: Photograph of the realized 23 GHz antenna array (C) in the cylindrical-parabolic reflector with uni-form feed distribution. Figure 9: Photograph of the realized 60 GHz antenna array (D) in the cylindrical-parabolic reflector with uni-form feed distribution.4 Conclusion The paper proposes a new class of printed antenna structures that have most of advantages of printed an-tennas: high reproducibility, low weight, compactness, possibility of simple integration with other passive and active microwave circuits as well as low manufactur-ing cost. At the same time they feature high gain and relatively low losses which is not common for planar printed antenna arrays. The only disadvantage com-paring to standard planar (2D) antenna structures is the third dimension, i.e. thickness, due to presence of the cylindrical-parabolic reflector. Four realizations of printed antenna arrays in cylindrical-parabolic reflector intended for various frequency ranges are presented, including antenna with high side lobe suppression for higher microwave ranges and antenna operat-ing in millimeter range (57.5–75.0)  GHz. Besides, pro-posed antenna structures are suitable for applications in beam scanning antennas as well as for forming the desired radiation pattern (for example, cosec2). Experi-mentally obtained results are in good agreement with those obtained by simulation.AcknowledgmentThe authors would like to thank colleagues Ms. M. Marjanović, Ms. M. Pesić, Mr. N. Tasić, Mr. M. Tasić and Mr. Lj. Radović for their help in realization of the an-tenna models. This work has been supported by the Serbian Ministry of Education and Science within the Technological Development Project TR 32024.A. Nešić et al; Informacije Midem, Vol. 43, No. 2(2013), 97 – 102102References1. A. Nesic, I. Radnovic, “High Gain Millimeter Wave Antenna with Cylindrical-Parabolic Reflector”, TELSIKS 2009, Nis, Conference Proc. pp. 376-3792. A. Nesic, I. Radnovic, “New Type of Millimeter Wave Antenna with High Gain and High Side Lobe Sup-pression”, Optoelectronics and Advanced Materi-als – Rapid Communications Vol. 3, No.10, Octo-ber 2009, pp. 1060-1064.3. A. Nesic, I. Radnovic, “60 GHz Range High Gain Printed Antenna Array with a Cylindrical-Parabol-ic Reflector”, Frequenz, 3-4/2010, Vol. 64 March/April 2010, 48-51.4. A. Nesic and D. Nesic, “Cylindrical-Parabolic An-tenna Fed by Printed Axial Array Like Primary Ra-diator”, Patent Pending no. P-207/0738, 24. Sep. 20075. A. Nesic, Z. Micic, S. Jovanovic, I. Radnovic , D. Nesic, “Millimeter Wave Printed Antenna Arrays for Covering Various Sector Width”, IEEE Anten-nas and  Propagation Magazine, Vol.49, No.1, Feb. 2007, pp. 113-1186. M. Mikavica, A. Nesic, CAD for Linear and Planar Antenna Array of Various Radiating Elements, AR-TECH House, Norwood, MA, 19927. J. H. C. van Heuven, “A New Integrated Wave-guide-Microstrip Transition”,  IEEE  Transactions on MTT, vol. 24, 1976, pp. 144-147 8. WIPL-D software package, http://www.wipl-d.com/, WIPL-D d.o.o.: Belgrade, Serbia, 20129. M. Petersson, Microstrip Solution for Innovative Mi-crowave Feed Systems, Department of Science and Technology, Linkoping University, Sweden, 200110. Rogers Corporation, MWI-2010, Calculator11. D. Nesic, I. Jokic, M. Frantlovic and M. Sarajlic, “Wide Band-stop Microwave Microstrip Filter on High-resistivity Silicon”, MIDEM - Journal of Micro-electronics, Electronic Components and Materi-als, vol. 42, no. 4, 2012, pp. 282-286Arrived: 26. 02. 2013Accepted: 08. 04. 2013A. Nešić et al; Informacije Midem, Vol. 43, No. 2(2013), 97 – 102

Cylindrical-parabolic reflector with printed antenna structures

Compte-rendu critique  « Écocritique, écosémiotique et représentation  du monde en littérature » de Gabriel Vignola             Le chercheur Gabriel Vignola propose dans son article d'élaborer un nouveau modèle théorique lié à l'écocritique et applicable à une certaine littérature, celle des « nature writings ». Ce courant de l'analyse littéraire né dans les années 1990, pose la question de la littérature à l'ère du contemporain et son rapport au monde. L'article se présente d'emblée comme un..

Charline Pluvinet

OpenEdition

L’écho écrit n°1 // Nature – 3

http://cer.ihtm.bg.ac.rs/bitstream/id/14643/MIDEM_43(2013)2p97.pdf

Cylindrical-parabolic reflector with printed antenna structures

Abstract

Similar works

Full text

Available Versions

Central Repository of the Institute of Chemistry, Technology and Metallurgy (CER)

OpenEdition