The multipurpose glove is a hand-worn device that wirelessly controls the position of a platform and flashes a high power LED at a particular frequency in order to alias the motion of an oscillatory object. The position and motion of the platform is dictated by an accelerometer which is attached to the top of the glove, as shown in Fig. 1. The user can then tilt the hand forward, backward, left, or right, to cause the platform to move towards a desired location. The user can also adjust the flashing frequency of the high power LED that is attached to the bottom of the glove. This frequency adjustment can be done through hand motion and the accelerometer, or by changing the position of a potentiometer that is attached to the overall casing, as depicted by Fig. 1. Figure 1 also displays the battery armature, which is used to fix the battery and secure the system casing around the forearm of the user with VELCRO straps

Davis, Destinee

Marques, João

Plantin, Thomas

English

Trinity University

Trinity UniversityDigital Commons @ TrinityMechatronics Final Projects Engineering Science Department5-2018Multipurpose Iron Man Glove & MoveablePlatformDestinee DavisTrinity University, ddavis2@trinity.eduJoão MarquesTrinity University, jmarques@trinity.eduThomas PlantinTrinity University, tplantin@trinity.eduFollow this and additional works at: https://digitalcommons.trinity.edu/engine_mechatronicsPart of the Engineering CommonsThis Report is brought to you for free and open access by the Engineering Science Department at Digital Commons @ Trinity. It has been accepted forinclusion in Mechatronics Final Projects by an authorized administrator of Digital Commons @ Trinity. For more information, please contactjcostanz@trinity.edu.Repository CitationDavis, Destinee; Marques, João; and Plantin, Thomas, "Multipurpose Iron Man Glove & Moveable Platform" (2018). MechatronicsFinal Projects. 7.https://digitalcommons.trinity.edu/engine_mechatronics/7               Multipurpose Iron Man Glove & Moveable Platform Group D Destinee Davis, João Marques, Thomas Plantin  (pledged)  April 30, 2018   Group D 1 TABLE OF CONTENTS DESIGN SUMMARY ................................................................................................................. 2 SYSTEM DETAILS ................................................................................................................... 3 DESIGN EVALUATION ............................................................................................................ 5 PARTIAL PARTS LIST ............................................................................................................. 6 LESSONS LEARNED ................................................................................................................ 7 REFERENCES ......................................................................................................................... 8 APPENDIX .............................................................................................................................. 9        Group D 2 DESIGN SUMMARY:  The multipurpose glove is a hand-worn device that wirelessly controls the position of a platform and flashes a high power LED at a particular frequency in order to alias the motion of an oscillatory object. The position and motion of the platform is dictated by an accelerometer which is attached to the top of the glove, as shown in Fig. 1. The user can then tilt the hand forward, backward, left, or right, to cause the platform to move towards a desired location. The user can also adjust the flashing frequency of the high power LED that is attached to the bottom of the glove. This frequency adjustment can be done through hand motion and the accelerometer, or by changing the position of a potentiometer that is attached to the overall casing, as depicted by Fig. 1. Figure 1 also displays the battery armature, which is used to fix the battery and secure the system casing around the forearm of the user with VELCRO straps.   Figure 1: Final design prototype with the glove (1), the system casing (2), and the battery armature (3) Group D 3 SYSTEM DETAILS:  Figure 2 exhibits a detailed picture of the design prototype with all the important user components. At first, the system is off, so to turn it on, the user must activate the main power switch. Once the switch is activated, power is delivered to the microcontrollers and electronics stored in the main casing. Battery power is also supplied to the DC-DC boost converter, which steps up the voltage from 11.1-V to 34-V in order for the high power LED to function when instructed.  The user now has a choice of three system modes, which are printed on the LCD. The first mode is the “Platform Control” mode, which allows the user to wirelessly control the platform’s motion through the accelerometer. Also, if the fan switch is activated, then the fan on the platform will engage. The second mode is the “LED Hand Control” mode, which can be entered by pressing the red push button. On the button press, the user LED on the system casing will blink, the piezo buzzer will sound, and the LCD will update its display. In this second mode, the user can activate the high power LED by positioning his palm normal to the ground, and can adjust the frequency by tilting his hand left or right. Retracting the wrist downwards causes the high power LED to disengage. Finally, the third mode is the “LED Pot Control” mode, which is also accessed via the red push button. In this mode, the high power LED is automatically turned on and its flashing frequency can be altered with the potentiometer.   Figure 2: Detailed design prototype with the LiPo battery (1), the power switch (2), the high power LED (3), the DC-DC boost converter (4), the accelerometer (5), the fan switch (6), the user LED (7), the potentiometer (8), the push button (9), the LCD (10), and the piezo buzzer (11, within the main casing) Group D 4 Figures A1-A4 in the appendix represent the functional diagrams of each microcontroller used in the project. Figure A1 combines the logic of two PIC microcontrollers, one which updates the display of the LCD, and one that both intakes the potentiometer value and communicates in binary with the Master Arduino. Portrayed in Fig. A2, the Master Arduino then reads the accelerometer value and outputs data to the transmitter. The transmitter then communicates the data to the receiver which then relays it to the Slave Arduino in Fig. A3. In essence, the Slave Arduino is merely a data bridge between the receiver and the platform PIC; it communicates in binary with the platform PIC, which then controls the motors and the fan according to Fig. A4.  Figures A5-A8 represent the various software flowchart. Figure A5 explains how the user interface scheme is structured, and Fig. A6-A8 explain the three principal modes that the system can enter while operating. From a more programming aspect, Fig. A9-A13 account for all of the necessary codes written both in the PIC Basic Pro and in the Arduino IDEs.  Finally, Fig. A14 displays the overall circuit schematic. This schematic is analyzed beginning from the lower-left corner where the Master PIC is positioned, and going around clockwise until the Platform PIC is reached. Reading the circuit this way enables one to follow what is occurring electrically among the microcontrollers, from the user input to the output signals linked to the actuators.      Group D 5 DESIGN EVALUATION:  The device successfully meets each of the requirements listed in the functional element categories. Our design meets the Output Display requirement by implementing a user LED as well as an LCD which prints the mode that the system is in. The Audio Output Device requirement is also fulfilled with the use of a piezo buzzer, which alerts the user when the main push button is pressed. The Manual User Input requirement is met with the use of a switch for the fan, of a push button for the system mode, and of a potentiometer for the adjustment of the flashing frequency of the high power LED. The requirement for the Automatic Sensor is satisfied with the use of an accelerometer, which both controls the flashing frequency of the high power LED and the motion of the platform. Our design achieves the Actuators, Mechanisms & Hardware section by implementing a servo motor controlled with a PWM signal. In addition, for this section, some 3D-printed parts were generated for the system casing and for the battery armature. Finally, for the Logic, Processing, and Control requirement, our device uses calculations (to output the correct flashing frequency of the high power LED to alias an oscillatory mechanism), multiple interfaced microcontrollers (interfacing the PICs with the Arduinos with binary communication), and an RF transmitter and receiver as components not included in other categories.   Group D 6 PARTIAL PARTS LIST: Part Name/Description Model Number Source (vendor) Price DC-DC High Power Boost Converter Hyelesiontek DC-DC Boost Converter  Ali Express $3.45 2.4GHz RF Transmitter and Receiver Module NRF24L01+ Amazon $2.40 Accelerometer MPU-6050 Banggood $2.66 Arduino Nano (2) Elegoo Nano board CH340 Amazon $8.57    Group D 7 LESSONS LEARNED:  Throughout the design and implementation of the device, our group encountered many problems and difficulties. The first main difficulty that we faced was how to setup a PIC microcontroller both to output to an LCD and intake the value of a potentiometer. In order to enable the PIC to output user information to an LCD, all of the PIC’s A/D converters had to be turned off. However, we needed a PIC A/D converter to read the potentiometer’s position. We solved this problem by interfacing two different PICs. These PICs communicated in binary via their I/O ports. Since the system only has three different modes, we were able to achieve full communication between both PICs with only two I/O pins on each PIC (for more detailed information, see Fig. A9 & A10).  Another difficulty that arose was the wireless communication between the hand module and the platform. Due to scarce information about PIC microcontrollers on the internet, we had a hard time achieving wireless communication between two PICs. However, we found a lot of information for wireless communication with Arduino systems, so we ended up using two Arduino Nanos, which made the setup and wireless communication tremendously easier.  One final problem that emerged during the testing of our product came from the DC-DC boost converter. One of the capacitors of the module failed, and we were not able to find another 1000-uF in time for the project demo the next morning. However, while searching for that component, we came across a box of 330-uF capacitors. We thus soldered three of them in parallel in a rosette-like shape, and replaced the 1000-uF capacitor with what we had just contrived. Basic circuit knowledge was a big help!  As far as recommendations go, we believe that the most important aspect of the project is to stay on schedule. Our group managed to advance at a regular pace throughout the semester and stay on schedule. If we had not done that, the problems we faced would have caused us to turn in our project late. On a more technical side, we would suggest to comment the code(s) properly and clearly. It helps everyone in the group to understand what is going on when the code(s) need(s) to be read. Finally, it is critical to update the circuit schematic as the circuit building takes place. It made it a lot easier to have an updated schematic when the circuit had to be transferred from the breadboard to the soldering board. Group D 8 REFERENCES: David G. Alciatore, Michael B. Histand, 2012, “Introduction to Mechatronics and Measurement Systems”, McGraw Hill, 4th edition, pp 301.  “LoRa Module VS nRF24 VS Generic RF Module || Range & Power Test”, https://www.youtube.com/watch?v=nP6YuwNVoPU  Gustavo Murta, “Arduino Strobe Light”, https://github.com/Gustavomurta/Arduino-Strobe-Light/blob/master/Arduino_Strobe_Gustavo.ino      Group D 9 APPENDIX:  Figure A1: Functional diagram of the Main PIC microcontroller   Figure A2: Functional diagram of the Master Arduino microcontroller       Main PIC microcontroller  Potentiometer  Push Button  Piezo sounder  High power  LED  Master Arduino  LCD screen   Main PIC  Transmitter Master Arduino  Accelerometer  High power  LED Group D 10  Figure A3: Functional diagram of the Slave Arduino microcontroller         Figure A4: Functional diagram of the Secondary PIC microcontroller (platform PIC)         Receiver  Secondary PIC Slave Arduino   Slave Arduino  Fan  Platform Motors Secondary PIC microcontroller Group D 11  Figure A5: Software flowchart of the user interface  Group D 12  Figure A6: Software flowchart of the platform control Group D 13   Figure A7: Software flowchart of the hand controlled LED flashing Group D 14  Figure A8: Software flowchart of the potentiometer controlled LED flashing   Group D 15  Figure A9: PIC Basic code of the user interface Group D 16  Figure A9: PIC Basic code of the user interface (Continued)  Group D 17  Figure A9: PIC Basic code of the user interface (Continued)  Group D 18  Figure A10: PIC Basic code of the potentiometer controlled LED flashing   Group D 19  Figure A10: PIC Basic code of the potentiometer controlled LED flashing (Continued)      Group D 20  Figure A11: PIC Basic code of the platform control  Group D 21  Figure A11: PIC Basic code of the platform control (Continued)        Group D 22  Figure A12: Arduino code of the transmitter / hand module  Group D 23  Figure A12: Arduino code of the transmitter / hand module (Continued)  Group D 24  Figure A12: Arduino code of the transmitter / hand module (Continued)       Group D 25  Figure A13: Arduino code of the receiver / platform module   Group D 26  Figure A13: Arduino code of the receiver / platform module (Continued)   Group D 27  Figure A14: Circuit schematic of the final prototype 

Multipurpose Iron Man Glove & Moveable Platform

https://digitalcommons.trinity.edu/cgi/viewcontent.cgi?article=1007&amp;context=engine_mechatronics

Multipurpose Iron Man Glove & Moveable Platform

Abstract

Similar works

Full text

Available Versions

Trinity University