The present study aims to predict the mechanical properties of similar and dissimilar aluminium alloy friction stir Welded joints. The present research also addresses the challenges in joining aluminium alloys Al5083 and Al6061 of 5mm thickness at varying process parameters. A total number of 24 joints have been fabricated with a set of eight joints each for Al6061(similar), Al5083(similar) and a combination of Al5083 x Al6061(dissimilar alloy) as per the experimental plan by Taguchi technique using L8 orthogonal array. The dimensions of the plates are chosen in such a way that the weld length is fixed to 150 mm. The tensile strength and the micro hardness of the welded joints as well as micro structures have been examined. Taguchi technique has been utilized to study the optimized value of the process parameters. The process parameters for joining these have been identified as rotational speeds at 1000 and 1600 rpm, traverse speed 40 and 160mm/min and axial force of 2.5 and 3.5kn

Abdullah, Ibrahim

Muhamad Arifpin, Mansor

Ramaraju, Ramgopal Varma

Yaswanth, Yatappu

UMP Institutional Repository

 STRUCTURAL PROPERTIES OF SIMILAR AND DISSIMILAR ALUMINUM ALLOY JOINTS BY FSW   Ramgopal Varma Ramaraju 1, Ph.D Senior Lecturer, Faculty of Engineering Technology, University Malaysia Pahang Gambang, Pahang, Malaysia ramgopal@ump.edu.my Abdullah Bin Ibrahim, Ph.D Professor Faculty of Engineering Technology,, University Malaysia Pahang Gambang, Pahang, Malaysia abi@ump.edu.my  Mohammed Arifpin Bin Mansor, Ph.D Senior Lecturer, Faculty of Engineering Technology, University Malaysia Pahang Gambang, Pahang, Malaysia arriffin@ump.edu.my  Yaswanth Yattapu Research Scholar Masters by Research Manufacturing Technology, Faculty of Engineering Technology  University Malaysia Pahang Gambang, Pahang, Malaysia yattapuyaswanth@yahoo.com   ABSTRACT The present study aims to predict the mechanical properties of similar and dissimilar aluminium alloy friction stir Welded joints. The present research also addresses the challenges in joining aluminium alloys Al5083 and Al6061 of 5mm thickness at varying process parameters. A total number of 24 joints have been fabricated with a set of eight joints each for Al6061(similar), Al5083(similar) and a combination of Al5083 x Al6061(dissimilar alloy) as per the  experimental plan by Taguchi technique using L8 orthogonal array. The dimensions of the plates are chosen in such a way that the weld length is fixed to 150 mm. The tensile strength and the micro hardness of the welded joints as well as micro structures have been examined. Taguchi technique has been utilized to study the optimized value of the process parameters. The process parameters for joining these have been identified as rotational speeds at 1000 and 1600 rpm, traverse speed 40 and 160mm/min and axial force of 2.5 and 3.5kn. INTRODUCTION Friction Stir Welding (FSW) is a fairly new type of joining process invented by TWI [1] in the year 1991. The studies on FSW are extensively used in many manufacturing applications and engineering as well. FSW has been proven to be an effective method to weld wrought aluminium alloys. Joining of metals by FSW results in less distortion, plastic deformation and less residual stresses [2-8].The process is operated below the melting temperatures[1] compared to conventional welding methods. A self- rotating tool with a pin at the bottom generates frictional heat which leads to metal deformation and this stirring action plasticizes the material to form a joint. The direction of rotating tool and weld direction are similar and travel along the weld path allowing plates to weld. The tool rotation and weld direction which are similar on one side are called "Advancing side" and opposite on the other called "Retreating side". This peculiar behavior of the weld makes this joint asymmetric when compared to conventional welds, which does not affect the heat affected zones. The physical phenomenon of the process helps one to identify the influence of process parameters on strength of the weld joint, among those factors are the tool rotational speed, traverse speed and axial force which are taken into consideration [9]. Hence, in the present study these parameters have been identified as the major influencing factors on the tensile strength and micro hardness. The earlier research studies on FSW of joining of similar and dissimilar metals by varying process parameters to identify change in mechanical properties of weldments can be seen in [10-15]. Studies on the effect of process parameters  by using mathematical tools either by Taguchi or Response Surface Methodology can be seen in [9, 17-24]. In all the studies reported earlier one can find optimized values of process parameters either for similar or dissimilar 1 Copyright © 2014 by ASMEProceedings of the ASME 2014 International Mechanical Engineering Congress and Exposition IMECE2014 November 14-20, 2014, Montreal, Quebec, Canada IMECE2014-36960 alloy joints. Hence there is a necessity to study the same on joining similar, dissimilar alloys by FSW. With this motive, the present research has been carried out to study the tensile strength, micro hardness and the effect of the process parameters on the same for similar (Al5083,Al6061) and dissimilar (Al5083 x Al6061) aluminium alloy joints. EXPERIMENTATION  The friction stir welded joints of similar and dissimilar Al5083 and Al6061 were fabricated using NC friction stir welding machine of 5T. A total of 24 joints were fabricated as per the Taguchi’s design plan. The chemical composition and the mechanical properties of the selected materials are given in table 1, table 2. The identified process parameters for the present investigation are given in table 3.  Table 1 Chemical Composition of Al 5083 and Al 6061 alloys[16]    Table 2 Mechanical Properties of Al 5083 and Al6061 alloys[16]  Al5083 Al6061 Yield Strength 228 MPa Yield Strength 276 MPa Ultimate Tensile Strength 317 MPa Ultimate Tensile Strength 310 MPa Elongation 16 % Elongation 12%  Hardness(Vickers) 96 Hardness(Vickers) 107  Table 3 Process Parameters[ 9]  Parameter Level 1  Level 2 Tool Rotational Speed (rpm) 1000 1600 Traverse Speed (mm/min) 40 160 Axial Force (kN) 2.5 3.5  A high carbon steel of 20 mm in diameter, shoulder diameter of 12 mm and a cylindrical pin of diameter of 5 mm is used in fabricating the joints. The schematic diagram and fabricated joint are shown in Fig. 1a and Fig. 1b.     Figure 1a Schematic Diagram FSW joint    Figure 1b Joint Fabricated by FSW  The test specimens for tensile[25] and micro hardness which are shown in Fig. 2a and Fig. 2b, were extracted by using a Mitsubishi EDM wire cut machine.    Figure 2a Schematic Diagram Samples of FSW Joint 2 Copyright © 2014 by ASME   Figure 2b Tensile Specimen of FSW Joint  The tensile and micro hardness tests were done by using Instron tester and Wilson computerized hardness tester. From each fabricated plate 5 samples were extracted for micro-hardness (2 samples) and tensile test (3 samples). A row of indentation tests have been carried out on the two samples moving by a distance of 0.1mm from the weld zone. As per the design plan a set 24 experiments were carried out with 3 samples each for the tensile test and the average value of the three is considered as the strength of the joint. Similarly a set of 24 experiments for micro hardness with 2 samples each have been considered using the average. The results obtained from the tensile test and the micro hardness is given in Fig. 3a, Fig.3b, Fig. 3c….. Fig. 3f.   Figure 3a Tensile Test Results of the fabricated Al 5083 FSW Joints   Figure 3b Tensile Test Results of the fabricated Al 5083 x Al 6061 FSW Joints    Figure 3c Tensile Test Results of the fabricated AL 6061 FSW Joints    Figure 3d Micro Hardness of the fabricated Al5083 FSW Joints   Figure 3e Micro Hardness of the fabricated Al5083 x Al6061 FSW Joints   Figure 3f Micro Hardness of the fabricated Al6061 FSW Joints  3 Copyright © 2014 by ASME MICRO-STRUCTURAL EXAMINATION The fabricated joints have been examined using an optical microscope to check for the defects. The Weck’s reagent has been used as the etching agent and the sample has been kept for about 5-10 minutes. The main aim of this examination is to verify the joining of the dissimilar alloys. The interface of the welded region is shown in Fig 4.    Fig 4 Microstructure of weld interface at 100x OPTIMIZATION The process parameters are optimized by choosing an L8 orthogonal array in Taguchi’s technique [26]. The process parameters taken into consideration at two levels are rotational speed, traverse speed and axial force. The chosen parameters are 1000 and 1600 rpm, 40 and 160mm/min, 2.5kN and 3.5kN. The optimization of these parameters has been carried out three different times by Qualitek4 software to predict the response of the influencing parameters. The array containing the design plan is given in Table 4.  Table 4 Experimental Design    The tensile strengths and micro hardness results, given as input for each sample of Al5083 are shown in Table. 5a. and Table 5b.   Table 5a Results of the Tensile strength for Al5083  Table 5b Results of the micro hardness for Al5083    Similar set of results for the Al5083 x Al6061 and Al6061 fabricated FSW Joints have been given as input for the Qualitek4 software. The result obtained from the analysis is given in Fig. 5a, Fig. 5b….. and Fig. 5f.   Figure 5a. Relative Influence of Factors on Tensile strength for Al5083  4 Copyright © 2014 by ASME  Figure 5b. Relative Influence of Factors on Tensile strength  for Al5083 x Al6061   Figure 5c. Relative Influence of Factors on Tensile strength  for Al6061     Figure 5d. Relative Influence of Factors on Micro Hardness for Al5083    Figure 5e. Relative Influence of Factors on Micro Hardness for Al5083 x Al6061    Figure 5f. Relative Influence of Factors on Micro Hardness for Al6061 DISCUSSION Experimental investigation states, by increased rotational speed, axial force and keeping weld speed constant there is a increase in tensile behavior and change in hardness values, and decrease in the same values when there is a increase in weld speed by keeping other parameters constant. Tensile strength increases due to change in axial force and insufficient frictional heat. If the weld speeds are high it reflects in poor heat generation and plastic flow of material. This is the reason for weak interface at the joint. High weld speed with low heat generation is not suitable for better joints, because the joints thus obtained have less strength and are low in metallurgical transformations. From the results obtained by the Taguchi Technique using Qulaitek4 software while welding either Al5083 or Al6061 alloys the influence of speed, traverse speed and axial force is observed as the most influencing parameter.  However, the most influencing parameter in joining dissimilar alloys is observed as the rotational speeds. The influence of the other factors one over the other is seen in all the cases. Hence, there exists a necessity to further study on the influence of process parameters by choosing higher levels.  CONCLUISIONS In the present investigation joining of Al5083, Al6061 and Al5083 x Al6061 has been achieved successfully. The tensile strength and micro hardness for the welded samples have been studied. The microstructural examination has been carried out to check the efficiency of the produced joint. An optimization tool Qualitek4 has been employed to study the influence of the process parameters on joining the similar and dissimilar alloys. ACKNOWLEDGMENTS The  authors  are  thankful  to  the  Ministry  of  Higher   Education (MoHe),  Malaysia  for  the  financial  support  provided  wide  RDU 130103  under  FRGS.  The  authors  are  also  thankful  to  the  Dr Zularism Dean  Faculty  of  Engineering Technology for  his support during the course of this work. 5 Copyright © 2014 by ASME REFERENCES [1] Thomas WM, Nicholas ED, Needham JC, Murch MG, Templesmith P, Dawes CJ. GB Patent  Application No. 9125978.8, December; 1991 [2] Dawes CJ. An introduction to friction stir welding and its development. Weld Metal Fabric 1995:13–16. [3] Mishra RS, Ma ZY. Friction  stir welding and processing. Mater Sci Eng R 50:1–78, 2005 [4] R. Nandan, T. DebRoy and H. K. D. H. Bhadeshia,Recent Advances in Friction Stir Welding– Process, Weldment Structure and Properties, Progress in Materials Science 53 pp.980-1023,2008. [5] Cam  G.  Friction  stir  welded  structural  materials  beyond  Al-alloys.  Int  Mater  Rev  56(1):1–48, 2011. [6] D Rao, K Huber, J Heerens, J F dos Santos, N Huber, Asymmetric mechanical properties and tensile behavior prediction of aluminium alloy 5083 friction stir welded joints, Materials Science and Engineering A 565, pp.44–50, 2013. [7] S Rajakumar, V Balasubramanian, Correlation between weld nugget grain size, weld nugget hardness and tensile strength of friction stir welded commercial grade aluminium alloy joints, Materials and Design 34, pp.242–251, 2012. [8] A. Heidarzadeh, H.Khodaverdizadeh, A.Mahmoudi. E.Nazari, Tensile behavior of Friction Stir welded AA6061 T4 Aluminium alloy joits, Materials and Design, Vol 37, pp. 166-173, 2012. [9] Hj Liu, JC Hou, H Guo, Effect of welding speed on microstructure and mechanical properties of self-reacting friction stir welded 6061-T6 aluminium alloy, Materials and Design 50, pp.872–878, 2013. [10] N Shanmuga, N Muragan, Tensile Behavior of Dissimilar friction stir welded joints of aluminium allaoys, Materials and Design 31, pp.4184–4193, 2010  [11] R Palanivel ,P  Koshy Mathews, The tensile behavior of friction stir welded dissimilar aluminum allaoys, Materials and Technology, 45(6), pp.623-626, 2011.  [12] P. Cavaliere, E. Cerri, A. Squillace, Mechanical response of 2024-7075 aluminium alloys joined by friction stir welding. Journal of Material Science, 40, 14, 3669–765, 2005. [13] T. Saeid, A. Abdollah-zadeh, B. Sazgari, Weldability and mechanical properties of dissimilar aluminum–copper lap joints made by friction stir welding. Journal of Alloys and Compounds, 490 1–2,652–655, 2010. [14] Bo Li, Zhenhua Zhang, Yifu Shen, Weiye Hu, Lei Luo, Dissimilar friction stir welding of Ti–6Al–4V alloy and aluminum alloy employing a modified butt joint configuration: Influences of processvariables on the weld interfaces and tensile properties, Materials and Design 53, pp.838–848, 2014. [15] S Kundu, D Roy, R Bhola, D Bhatacharjee, B Mishra, S Chatarjee, Microstructural and tensile strength of friction stir welded joints between interstitial free steel and commercially pure aluminium,  Materials and Design 50, pp.370–375, 2013. [16] Metals Handbook, Vol.2 - Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International 10th Ed. 1990. [17] K. Elangovan, V. Balasubramanian, S. Babu, Predicting tensile strength of friction stir welded 6061 aluminium alloy joints by mathematical model. Material and Design, 30 1, 88–1, 2009. [18] Rajakumar S, Muralidharan C, Balasubramanian V. Establishing empirical relationships to predict grain size and tensile strength of friction stir welded AA 6061-T6 aluminium alloy joints. Trans Nonferrous Met Soc China 20:1863–72, 2010. [19] Rajakumar S, Muralidharan C, Balasubramanian V. Predicting tensile strength, hardness and corrosion rate of friction stir welded AA6061-T6 aluminium alloy joints. Mater Des 32:2878–90, 2011. [20] A K Lakshminarayana, V Balasubramanian, Process parameters optimization for  friction stir welding of RDE-40 aluminium alloy using Taguchi technique, Trans. Nonferrous Met.Soc.China 18, pp.548-554, 2008 [21] M Jayaraman,V Balasubramanian, Effect of procees parameters on tensile strength of friction stir weld cast A356 aluminium alloy joints, Trans. Nonferrous Met.Soc.China 23, pp.605-615, 2013 [22] Elangovan K, Balasubramanian V, Babu S. Predicting tensile strength of friction stir welded AA6061 aluminium alloy joints by a mathematical model. Materials and Design,30, pp. 188–93, 2009. [23] S. Rajakumar C. Muralidharan,  V. Balasubramanian, Establishing empirical relationships to predict grain size and tensile strength of friction stir welded AA 6061-T6 aluminium alloy joints, Trans Nonferrous Met Soc China Volume 20, Issue 10, October, pp. 1863–1872, 2010. [24] S Rajakumar, C Muralidharan, V Balasubramanian. Optimization of the friction-stir-welding process and the tool parameters to attain a maximum tensile strength of AA7075-T6 aluminium alloy [J], Journal of Engineering Manufacture, 224.pp. 1175–1191, 2010. [25] ASTM E8M-09. American society for testing and materials (ASTM). In :Standard test methods for tension testing of metallic materials, vol. 03.01. West Conshohocken (PA): Annual book of ASTM standards; 2009. Taguchi’s Quality Engineering Handbook, Genichi Taguchi, Subir Chowdhury, Yuin Wu, Wiley, 2005.  6 Copyright © 2014 by ASME

Structural Properties Of Similar And Dissimilar Aluminum Alloy Joints By FSW

http://umpir.ump.edu.my/id/eprint/8197/1/STRUCTURAL_PROPERTIES_OF_SIMILAR_AND_DISSIMILAR_ALUMINUM_ALLOY.pdf

Structural Properties Of Similar And Dissimilar Aluminum Alloy Joints By FSW

Abstract

Similar works

Full text

Available Versions

UMP Institutional Repository