This paper presents the practical microcontroller implementation of single phase inverter switching strategies

Daut, I.

Fauzy, F.

Isa, M.

Ismail, B.

Mohd Saad, A.R

Taib, S.

English

Repository@USM

MICROCONTROLLER IMPLEMENTATION OF SINGLE PHASE INVERTER SWITCHING STRATEGIES   ¹B. Ismail, ² S. Taib, ¹ M. Isa, ¹ I. Daut, ³ A.R Mohd Saad , ¹F. Fauzy                          ¹ School of electrical system engineering, UniMAP Blok A, kompleks pusat pengajian, Jalan Kangar-Arau, 02600 Arau Perlis ²CETREE, Komplek Eureka, USM, 11800 Pulau Pinang.  ³Engineering Centre, UniMAP baha@kukum.edu.my, soibtaib@eng.usm.my   Abstract      This paper presents the practical microcontroller implementation of single phase inverter switching strategies. The attractiveness of this configuration is the used of a microcontroller to generate sinusoidal pulse width modulation (SPWM) pulses. The difference amplitude modulation ratio am  starting from 0.3 until over modulation with 2 KHz switching frequency was implemented and tested. Selected results from the experimental prototype will be presented. The result shows the relationship between amplitude modulation ratio with total harmonic distortion (THD) and dead time period.    1. Introduction      SPWM or sinusoidal pulse width modulation is widely used in power electronics to digitize the power so that a sequence of voltage pulses can be generated by the on and off of the power switches. The pulse width modulation inverter has been the main choice in power electronic for decades, because of its circuit simplicity and rugged control scheme [1]. SPWM switching technique is commonly used in industrial applications. SPWM techniques are characterized by constant amplitude pulses with different duty cycle for each period. The width of this pulses are modulated to obtain inverter output voltage control and to reduce its harmonic content [2]. Sinusoidal pulse width modulation or SPWM is the mostly used method in motor control and inverter application. In this development a unipolar SPWM voltage modulation type [3]-[4] is selected because this method offers the advantage of effectively doubling the switching frequency of the inverter voltage, thus making the output filter smaller, cheaper and easier to implement. Conventionally, to generate this signal, triangle wave as a carrier signal is compared with the sinusoidal wave, whose frequency is the desired frequency.      The proposed alternative approach is to replace the conventional method with the use of microcontroller. The use of the microcontroller brings the flexibility to change the real-time control algorithms without further changes in hardware. It is also need low cost and has a small size of control circuit for the single phase bridge inverter.     To achieve the control system an Atmel AT89C2051-24PI microcontroller was used. The atmel AT89C2051-24PI is a low voltage, high performance CMOS 8-bit microcomputer with 2K bytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmel’s high density nonvolatile memory technology and is compatible with the industry standard MCS-51 instruction set. It also has two 16-bit timers that deliver the function use in this application.  By combining a versatile 8 bit CPU with Flash on a monolithic chip, the Atmel AT89C2051 is powerful microcomputer with provides a highly flexible and cost effective solution to many embedded control applications.  2. Pulse Width Modulation Control      The frequency modulation ratio mf is defined as the ratio of the frequencies of the carrier and the reference signals which is written as  sinffffmf trireferencecarrier ==                   (1)  The amplitude modulation ratio am is define as the ratio of the amplitude of the reference and carrier signals and is given by  International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),Johor Bahru, Johor, Malaysia, May 28-29, 2007104 carriermmcarriermreferencemaVVVVm,sin,,, ==        (2)      The amplitude of the PWM of the fundamental frequency output is controlled by am . This is significant for an unregulated DC voltage because the value of am  can be adjusted to compensate the variations in the DC voltage, thus producing a constant amplitude output. If  am  is greater than 1 or over modulation, the amplitude of the output increases with am ,  but not linearly.   3. Approach and Method       Figure 1 below show the full bridge single phase inverter and its switching strategy.     Figure 1: Single phase full bridge inverter      Figure 2 shows the strategy control of the switching technique for the inverter. The gS1, gS2, gS3 and gS4 are output gating signal for power switchers S1, S2, S3 and S4 respectively. Figure 2a shows the comparing signal between carrier signal and reference signal. While figure 2b shows the pulse for the power switchers and figure 2c shows the output of the inverter. In this development every pulses for gS1, gS2, gS3 and gS4 was programmed by using microcontroller. The size of the pulses is depended on the comparison between carrier signal and reference signal. When the amplitude modulation ratio ( am  ) is difference, the size of the pulse also difference. Both gating signal (gS1 and gS3) and (gS2 and gS4) used the same control signal generated by the microcontroller. The different is only (gS1 and gS3) signal is leading (gS2 and gS4) by half cycle or 180 degree of the switching signal. Figure 3 below clearly illustrated the comparison signal between carrier signal and reference signal and the gating pulses signal (Vg).   Figure 2: Strategy control of the switching technique    Figure 3: Comparison signal and gating pulses signal  4. Experimental Results and Discussion      The selected results have been chosen to illustrate some of the main features of microcontroller SPWM control, which have been presented in this paper. Figure 4 shows the switching signal for difference amplitude modulation ratio, started from 0.3 until 1.5.  Figure 5 shows the output voltage and current for single phase inverter after the filter with amplitude modulation is 1.3.  International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),Johor Bahru, Johor, Malaysia, May 28-29, 2007105                                           (a)                                  (b)                                  (c)                                            (d)                                             (e)                                             (f)                                            (g)                                            (h)                                  (i)                                             (j)                                        Figure 4: Switching signal for difference amplitude modulation ratio (a) am =0.3, (b) am =0.4, (c) am =0.5, (d) am =0.6, (e) am =0.7, (f) am =0.8, (g) am =0.9, (h) am =1.0,  ( i ) am =1.3, ( j ) am =1.5                                                          X-axis: 1div= 1ms, Y-axis: 1div=2V  International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),Johor Bahru, Johor, Malaysia, May 28-29, 2007106  Figure 5: Output of the inverter after filter with resistive load for am =1.3 (100V/div), (1A/div)       A comparison of the total harmonic distortion (THD) for difference amplitude modulation ratio shows that the total harmonic distortion increase started from am =0.3 until am =0.6. Total harmonic distortion for am =0.7 to am =1.3 is decrease when the amplitude modulation is increase and THD increase back when amplitude modulation ratio, am =1.5. This can be seen in Figure 6. A comparison of the dead time period for difference amplitude modulation ratio shows that the dead time period decreases when am  is increase. This can be seen in Figure 7.     Figure 6: THD versus amplitude modulation ratio    Figure 7: Dead time period versus amplitude modulation ratio 5. Conclusion     The main task in this work is to find the best switching pulses generated by microcontroller with difference amplitude modulation ratio. Amplitude modulation ratio, am =1.3 produced good total harmonic distortion for both voltage and current. THD produced by that signal is less than 3% (after filter). The implementation of the single phase SPWM switching signal using microcontroller is placed on minimization of the hardware requirement, with as many functions as possible being performed in the software. Using microcontroller unit, the amplitude  modulation ratio and duty cycle can be  easily change through programming without further hardware changes.   6. References  [1] B. Ismail, S.Taib, A.R Mohd Saad, M.Isa, I.Daut. “Development of Control Circuit for Single Phase Inverter Using Atmel Microcontroller”, Proc. Of the International Conference of Man-Manchine System, Langkawi, 2006.   [2] B. Ismail, S.Taib, A.R Mohd Saad, M.Isa, C.M Hadzer.  “ Development of a Single Phase  SPWM Microcontroller-Based Inverter”, Proc.of the First International Power and Energy Conference, PECon 2006, Putrajaya, pp 437-440.   [3] L. Mihalache. “DSP Control Method of Single –Phase Inverters for UPS Applications”. IEEE Trans. On Industry Application. 2002, pp 590-595.  [4] N. Mohan, T.M.Undeland, W.P.Robbins, “ Power Electronic-Converters, Applications and Design”, Second edition, John Wiley & Sons Inc., 1995.  International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),Johor Bahru, Johor, Malaysia, May 28-29, 2007107

Microcontroller Implementation Of Single Phase Inverter Switching Strategies.

Abstract

Similar works

Full text

Available Versions

Repository@USM