We performed an experimental study on the pulse forming mechanism in an AM mode-locked hybrid TEA-CO2 laser by means of “injection mode-locking”. The results show that bandwidth limited pulses will only be reached within a small - critical - range of parameters. Furthermore, under some stringent conditions, the pulse-widths obtained become comparable to the non-hybrid case. We demonstrate also that the relation between the pulse-width and the modulation-depth is not different from a non-hybrid AM mode-locked TEA-CO2 laser

Bonnie, R.J.M.

Goor, F.A. van

English

We performed an experimental study on the pulse forming mechanism in an AM mode-locked hybrid TEA-CO 2 laser by means of &quot;injection mode-locking&apos;. The results how that bandwidth limited pulses will only be reached within a small-critical- range of parameters. Furthermore, under some stringent conditions, the pulse-widths obtained become comparable to the non-hybrid case. We demonstrate also that the relation between the pulse-width and the modulation-depth is not different from a non-hybrid AM mode-locked TEA-CO2 laser. 1

R. J. M. Bonnie

F. A. Van Goor

CiteSeerX

PULSE FORMING IN AN AM MODE-LOCKING HYBRID TEA-CO 2 LASER

van Goor, F.A.

University of Twente Research Information

Volume 58, number 3 OPTICS COMMUNICATIONS 1 June 1986 PULSE F O R M I N G  IN AN AM M O D E - L O C K I N G  HYBRID TEA-CO 2 LASER R.J.M. BONNIE and F.A. VAN G O O R  Department of Applied Physics, Twente University of Technology, Enschede, The Netherlands Received 25 November 1985; revised manuscript received 17 January 1986 We performed an experimental study on the pulse forming mechanism in an AM mode-locked hybrid TEA-CO 2 laser by means of "injection mode-locking'. The results show that bandwidth limited pulses will only be reached within a small - critical - range of parameters. Furthermore, under some stringent conditions, the pulse-widths obtained become comparable to the non-hybrid case. We demonstrate also that the relation between the pulse-width and the modulation-depth is not different from a non-hybrid AM mode-locked TEA-CO2 laser. 1. Introduction A widely accepted method for generating short pulses in the nanosecond region in (pulsed) CO 2 lasers is active mode-locking by means of an intra cavity acousto-optic modulator. It can be shown that in a typical AM mode-lock experiment, pulse widths in the order of  1 ns are feasible. Because the laser starts to oscillate from the spon- taneous emission induced noise, a large number of  rondtrips is needed (especially at low values of  the modulation depth) to produce stable and reproducible pulses. This requirement is not always fulfilled when dealing with TEA-CO 2 lasers. To overcome this problem, several stabilization techniques have been developed. The easiest is the inclusion of a low pres- sure cw-section in the cavity [1]. This mode-locking of  a hybrid TEA-CO 2 laser offers the facility to pro- duce pulses with variable durations between 1 and 10 ns. A disadvantage of this technique however is the additional broadening of the pulses compared to the non-hybrid case. Injection of monochromatic radiation from a cw- CO 2 laser in an AM mode-locked TEA-CO 2 laser re- suits in very stable pulses without the disadvantage of broadening [2]. On the other hand, this technique ap- pears to depend critical on a proper frequency match- ing between both lasers. Three observations have strongly encouraged us to 0 030-4018/86/$03.50 © Elsevier Science Pubh.'shers B.V. (North-Holland Physics Publishing Division) study the pulse forming in a hybrid AM mode-locked TEA-CO 2 laser: (i) The additional broadening of the pulses from the mode-locked laser, when dealing with an intra- cavity cw-CO 2 stabilization cell. (ii) Mode-locking of a hybrid laser results in a pulsewidth varying with the modulation depth 8m as 8m 0"55 , in contrast to the/~m 0"25 dependence in the non-hybrid case [ 1 ]. (iii) Pulse-durations in rich mixtures - i.e. mix- tures containing little helium - can be considerably longer than in lean mixtures (containing much helium). Unless the observed pulses are not bandwidth limited, this is in contradiction with the generally accepted equation for the bandwidth of a typical CO 2 laser [3] ; according to this, bandwidth increases with de- creasing helium percentage. Hence, the pulse duration should increase with increasing helium percentage. 2. Description of the experiment Injection of the radiation from the AM mode- locked hybrid TEA-CO 2 laser in a high pressure TE- CO 2 regenerative amplifier at various delay-times of- fers the opportunity to study the time evolution of the pulse running in this oscillator. Using this tech- nique it is possible to perform measurements even in those regions where the radiation level is too low to 211 Volume 58, number 3 OPTICS COMMUNICATIONS 1 June 1986 loo % Ao high-pressure TE- COp so% G~ i / \ \  I - '" ,,,o, + tl electronic 100 % Au I I / \Nx,,.. / /  i ,/ 2.5 m TEA- C 0 z tow-pressure cw-CO 2 photon-drag 0% G,e - \ = _ ,  J AH-modulai'or 76% Ge I piano 2.5 m diaphragm / Fig. 1. Experimental configuration. detect with any kind of available detector. The experimental configuration is shown in fig. 1. Because we already discussed this setup in detail [4], we shall give a brief description only. The injection source is formed by a single-discharge TEA-CO 2 section with an active volume of  20 X 1 X 1 cm 3 , a 55 cm long low pressure section filled with 20 Torr of  a CO 2 : N 2: He = 1 : 2 : 5 mixture and a 40 MHz acousto-optic AM-modulator. The amplifier is a double-discharge, UV-preionized TE-CO 2 laser with an active volume of 30 X 0.8 X 0.8 cm 3 , operating on 5 atmospheres o f a  CO2:N2:He = 1 : 1 : 10 mixture. This high pressure results in an effective bandwidth of roughly 25 GHz, sufficiently large to minimize the effect of  broadening or distortion of  the injected pulses by the (dispersive) amplifying medium. The ra- diation is injected in the amplifier through its out- coupling mirror. The output  of  both  the injector and the amplifier is monitored via two photon-drag detec- tors on a Tektronix 7912 AD transient digitizer. The delay between both lasers can be varied elec- tronically. To circumvent the effect of  jit ter in the triggering of  the lasers, we also measured the delay by observing the light-signals coming from the last spark- gaps of  the Marx-generators of  the lasers. We measured under several experimental condi- tions the pulse-duration as a function of  the delay time; the results of  a typical measurement are shown in fig. 2. The intensity profile o f  the envelope of  the output  pulse from the oscillator, as detected by ~0 3,5 3.0 "7 2.5 ~ 2o 15 1.0 ..... -1;0 -0-'5 C02:N2:He = 1:1: 6. EW:t~mA 6m=0.12 00 0.5 1,0 1'5 2'0 T{lasl Fig. 2. Duration of  the mode-locked pulses as a function o f  t ime; the intensity prof'fle o f  the envelope of  the pulse-train as detected by  means o f  a photon-drag detector  is also shown; t = 0 is chosen to coincide with the maximum of  the inten- sity profile. means of  a photon-drag detector, is also shown. We have chosen the time scale in such a way that the maximum of  this intensity profile coincides with T=0.  212 Volume 58, number 3 OPTICS COMMUNICATIONS 1 June 1986 3. Experimental  results and discussion 3.1. Pulse-width as a function o[ the helium concentration When the pulse-width is measured directly by means of e.g. a photon-drag detector, one has to be careful in interpretating the results. As is demonstrated clearly in fig. 2, the time necessary for the pulse- forming to reach steady state may be considerably longer than the build-up time for the radiation field. For this reason, the measured width on its turn can be larger than expected from steady-state theory. Keeping the ratio CO 2: N 2 = 1 : 1, we measured as a function of  the helium percentage for two values of the modulation depth parameter (6 m) the pulse-width directly (rm) - i.e. at the moment of  output intensity was at maximum - and also in steady state (%). The results are shown in figs. 3a and 3b. Restricting to rm, one could conclude that the pulse-width indeed decreases with increasing helium percentage; however, the values of  r s indicate that the pulse-width is independent from the helium concen- tration (there may be a small dependence, but this is within the experimental error). These observations can be explained as follows. Decreasing the amount of helium in the laser gas mix- tures increases the gain (keeping the other experi- mental parameters unchanged). So less roundtrips are needed before the laser passes threshold and the gain switches. Thus there is also less time available for the pulse forming process. This time may be insufficient to reach steady state and the measured pulse dura- tions may be longer than expected from steady-state theory. To check this interpretation, we measured the delay between the pump-pulse of  the laser and the op- tical output. The results are shown in fig. 4. As ex- pected, the delay increases with increasing helium percentage. The transient behaviour of the pulse width from 2.S 2.0 1.5 C T L L  1-0 0.S <•: T m ~: "IS • : Xm-calculated 2.5 2.0 i s  6m: 0.12 "T" 1-0 0.5 ~:-c m t:T S =: xm- calcutated 6 m = 0.64 (a) Co) 7'0 ' ' ' . . . . .  60 80 90 100 60 70 80 90 100 % He % He Fig. 3. Pulse width measured in the maximum of the intensity profile (rm) and in steady-state (rs) as a function of the helium per- centage. Calculations for rm according to eq. (1) are also shown. 2!3 Volume 58, number 3 OPTICS COMMUNICATIONS 1 June 1986 "G 3 - 1  _ J  C 3  1 + I I I I t t I / I /  / 4 / I  I +_.J( +: 6m: 0-6L, 4: 6m= 0-12 I I I | I 60 70 80 90 100 */.He Fig. 4. Delay between the electrical pump pulse and the most intense pulse in the train for different helium percentages. an AM mode-locked laser can - in analytical form - be described by [5] r = r s / [ tanh( t / to )  ] 1/2, (1) where r s is the steady state pulse width, t o = (Af)[8,v/2gl/261m/2f2 ' 6 m is the modulation depth, g is the steady state gain, fm is the AM modulator drive frequency, and Af  is the bandwidth of the medium. Using both these delays between the pump-pulse and the appearance of  the most intense pulse in the output train and the steady-state pulse duration at various helium percentages, we may calculate accord- ing to eq. (1) the width of  the most intense pulse as a function of  the helium concentration. The calculated curves are also shown in the figs. 3a and 3b. 3.2. Pulse width as a function o f  the modulation depth We measured at three different places in the pulse train the pulse duration as a function of  the modula- tion depth (Sm):r  s pulse width in steady state, r m width of  the strongest pulse in the train, and r d width of  one of the first directly detectable pulses - i.e. 0.4 /as before the strongest pulse. ' ] :T  d 2 "7 -r" U_ 1 0.9 0.8 0.7 1.0 ' . . . . . . . .  01 & . . . .  tim Fig. 5. Variation of pulse duration r with the modulation depth a m. The full lines are the best straight-line-fits through the data. See text for an explanation of the indices d, m, s. 214. Volume 58, number 3 OPTICS COMMUNICATIONS 1 June 1986 t~0 { ts 3.0 2.5 t m ~20 t~ GJ 1.5 1-0 ~5 I I i 0.1 (~2 0.3 04 0.5 06 (~7 6m Fig. 6. Delay measurements corresponding to the pulse width measurements of flg. 5. Because we are interested in the relation between r and/tm, we plotted in fig. 5 r versus/~m on a double logarithmic scale; also the best straight-line-fit through the data has been drawn. From these results, we ob- tain the following relation: r / =  ro~ m i , (2) where i is d, m, s, respectively, r 0 is the observed steady-state pulse-width for 8 m = 1; 7" 0 = 0.74(4) ns, a d = 0 . 5 5 ( 3 ) ,  e m = 0 . 4 3 ( 3 ) ,  a,=0.25(I); (3) note that these results are for a CO 2: N 2 : He = 1 : 1 : 3 mixture. It is seen from this figure that the value o f  the parameter ~ in formula (2) strongly depends on the position of  the pulse in the output-pulse-train. More exactly, the parameter or/is correlated with the delay between the electrical pump-pulse o f  the laser and the ith pulse in the train. For the three cases as described above, we measured - for the same mixture - also the delay as a function o f  the modulation depth. The results are shown in fig. 6. From these delay meas- urements we constructed fig. 7 according to [5] r = rormll4/[tanh(t/to)] 1/2. (4) Next we wish to fit the data depicted in fig. 7 with Xd',~ \ \ \ \ t rn" ".. \ \o -.. \ \ \ \ "N o \ t  \ \ t ,  \ \ .\ .. .\ ~.. oN t i 0 i 5 , , A , , , , , , O- 0-1 0.5 6m I 0.9 0.8 0.7 m. 'tO 2 "7 t -  " l -  u_ Fig. 7. Calculated variations of the pulse width with the modulation depth according to eq. (4), using the delay measurements of fig. 6. 215 Volume 58, number 3 OPTICS COMMUNICATIONS 1 June 1986 relation (2); from this first order fi~, we obtain: C~d=0.55(2 ), C~m=0.47(2 ), % = 0 . 2 8 ( 2 ) .  (5) Comparison of these results to those obtained before (3) shows that the exponential behaviour is quite well described by the transient solution of Siegmann and Kuizenga (eq. (4)). Hence, we might explain the unexpected 6-°.55 behaviour of ref. [ 1 ] as caused by the fact that the pulse forming process in the laser system used has not already reached steady state at the moment of detec- tion of the pulses. 3.3. Additional broadening due to the stabilization cell We performed also some measurements with the low pressure cw420 2 section switched off. We deter- mined the steady-state pulse-duration as a function of the modulation depth. Comparising these results to the ones obtained with the stabilization cell active, we measured only a very small broadening (rs)cw.on = 1.06(2) * (rs)ew.of f . (6) This small additional broadening might be explained as a rest-effect due to the cw-section; i.e. the low pressure gain is not completely depleted in the steady state. The resulting effective bandwidth of both the TEA laser and the low pressure cell will then be smaller, yielding an enlarged pulse width. 4. Conclusions Summarizing the present results, we come to the following conclusions: - Pulses produced during (or before) the gain switch in an AM mode-locked hybrid TEA-CO 2 laser may not be bandwidth limited, especially when deal- ing with a high gain system. - The broadening of the pulses from an AM mode- locked hybrid TEA-CO 2 laser is neglectable compared to the pulses from a non-hybrid system under the as- sumption that enough time is available for the pulse forming to approach steady state. This can be establish- ed by using low-gain gas mixtures (high percentage helium), low pumping rates or high cavity loss factors (low outcoupling reflection). - The pulse-width varying with the modulation parameter 6m as 6m 0"55 as reported in ref. [1] can be explained by the assumption that the pulse-forming process has not reached steady state. Looking at dif- ferent stages of the pulse-forming process, we obtain different values for the exponential dependence on the modulation parameter 6 m. Acknowledgements This investigation was made possible by the finan- cial support of the Dutch "Stichting voor Fundamen- teel Onderzoek der Materie". References [1] P. Bernard and P.A. B61anger, Optics Lett. 4 (1979) 196. [2] F~A. van Goor, Optics Comm. 45 (1983) 404. [3] R.L. Abrams, Appl. Phys. Lett. 25 (1974) 609. [4] F.A. van Goor, R.J.M. Bonnie and W.J. Witteman, IEEE J. Quant. Electron. QE-21 (1983) 1772. [5] A.E. Siegman and DJ. Kuizcnga, Opto-Electron S (1984) 43. 216 

Pulse forming in an AM mode-locking hybrid TEA-CO2 laser

https://research.utwente.nl/en/publications/a0fa3992-bb43-47e3-9664-86927e56fb35

Pulse forming in an AM mode-locking hybrid TEA-CO2 laser

Abstract

Similar works

Full text

Available Versions

CiteSeerX

University of Twente Research Information