This paper describes the design and construction of Dribbel, a passivity-based walking robot. Dribbel has been designed and built at the Control Engineering group of the University of Twente. This paper focuses on the practical side: the design approach, construction, electronics, and software design. After a short introduction of dynamic walking, the design process, starting with simulation, is discussed

Dertien, Edwin

English

Dertien, Edwin C.

University of Twente Research Information

IEEE Robotics & Automation Magazine SEPTEMBER 2006118L A B C O R N E RDynamic Walkingwith DribbelDesign and Construction of a Passivity-Based Walking RobotBY EDWIN DERTIENThis article describes the design and construction ofDribbel, a passivity-based walking robot. The robothas been designed and built at the Control Engineeringgroup of the University of Twente. The current version of therobot can be seen in Figure 1. Passivity-based walking, ordynamic walking, is an approach to walking research focusedprimarily on the dynamics of the mechanical system used forwalking; control and actuation come second. This articlefocuses on the practical side: the design approach, construc-tion, electronics, and software design. After a short introduc-tion of dynamic walking, the design process, starting withsimulation, will be discussed.Dynamic WalkingTad McGeer started this field of research in the early 1990swith the design of totally passive (unactuated) mechanicalwalking constructions. His walkers were able to walk down ashallow slope without any form of active control or actua-tion. Based on the same dynamics principles, actuated (butstill underactuated) walkers are being built today. Thesewalkers can walk stably on a flat floor. Dribbel, the walkerthat is decribed here, has five joints, one of which is actuated.SimulationA number of simulation models preceded the working robot.Figure 1. The current design of the walking robot Dribbel.Figure 2. Screenshot of the 3-D simulation model made withthe 20-sim 3-D mechanics editor.SEPTEMBER 2006 IEEE Robotics & Automation Magazine 119First, a simple model investigating the basic weight distribu-tion and power requirements for the robot was made. Thesize of the robot chosen was roughly at human size, with legs1 m in length, a weight of roughly 10 kg primarily located inthe hip. From this model, the required hip torque for therobot was derived, requiring peaks of 10 Nm.Confident about the chosen components and sizes, a startwas made designing the robot’s mechanics in SolidWorks,while simulating the robots behavior in more detail in thesimulation environment.For the simulations, the power-port-oriented package 20-sim [5] was used. This package uses bond-graph notation(besides standard block diagrams and equations) in order tomake power-continuous domain-independent models. Forthe three-dimensional (3-D) kinematics and dynamics, thespecial 3-D mechanics toolbox in 20-sim has been used,which provides the user with a simple drag-and-drop draw-ing interface for kinematic structures (see Figure 2). Internal-ly, this package delivers equations using screw theory [4].The model was used for testing the controller algorithm,testing the effect of adding extra battery weight, etc. After themechanical prototype was built, the simulation model hasbeen tuned to match the exact robot behavior so that withfuture experiments even more accurate predictions could bemade based upon simulation results. Figure 3 shows the simi-larity between the hip angle in simulation and measurementafter tuning the simulation. In order to approximate the behavior of a purely passivemechanism, the desire was to build the actuated part back-drivable. With a geared motor, this is only possible by addingcontrol. By means of a torque sensor, the hip joint can becontrolled to a zero-torque state, in doing so acting as a com-plete passive joint. Other mechanical elements such as springscan be superimposed to this zero-torque system, emulatingthe behavior of a passive joint with springs.ControlFor the hip actuator in both the simulation environment and thereal robot, a simple proportional-differential (PD) control algo-rithm is used: the setpoint for the controller is switched on footimpact. This simple control has been used by other powered“passive” designs [3]. By changing the setpoint and controllergain, the walking gait of the robot can be influenced. The con-troller is tuned to have a very weak action. The swing leg willreach the setpoint but will fall back immediately due to gravityso that the angle between the legs on impact is much smallerthan the given setpoint. At the start of the swing phase, the con-troller gain can be seen as the spring constant of a passive springconnected between the stance leg and swing leg. The product ofthe setpoint and the gain is a measure for the amount of initialtorque with which the leg is being swung forward.MechanicsThe hip is the most important joint in this robot, being theonly one actuated. The hip is thus designed around the mainactuator: a Maxon RE40 150-W brushed DC motor withheavy (1:73) gearbox. The mechanical design of the hip consistsof a 50-cm aluminium tube 6 cm in diameter. With large SKFbearings, an 8-cm-diameter tube is fitted around this tube. Theouter legs are mounted on the inner tube, the inner legs on theouter tube. The motor is mounted in the inner tube, and theoutput power is transferred using an Oldham coupling, via atorque sensor, to the outer tube as can be seen in Figure 4.The tubular design was chosen because a tube has the bestknown stiffness-to-weight ratio for a hollow object; it is anice way to have mounting space for the motor and electron-ics while accomodating the joint. Not very scientific butequally important, it looks cool. The upper and lower legs consist of rectangular hollow alu-minium bars that can be bolted onto snug fitting pieces on thehip tube, knees, and feet. All joints can be disconnected by sim-ply removing four screws, so the design is very modular andallows for easy installment of different knees or feet modules.Already two sets of feet have been tested: 1) simple mea-suring feet (including an encoder), which are criticallydamped, almost all energy is immediately lost on impact, and2) also a set of more compliant feet has been designed andtested, resulting in a more efficient walking motion [7]. For the knees, a latching mechanism had to be designed.The first design consisted of a latching system where a sole-noid had to retract a locking pin. This system failed terribly.When the leg was under stress, the solenoid could never gen-erate the amount of force necessary to retract the locking pin.A quick-and-dirty solution was a completely different designusing door locking magnets. This system required an oppositescheme of powering: active locking instead of active unlock-ing. Both of the mechanisms can be seen in Figure 5.Figure 3. Hip angle during a short, straight walk in both thesimulation and real robot.0.40.200 2 4 6 8 10 12−0.2−0.4Time (s)Hip Angle ComparisonRealDribbelModelIEEE Robotics & Automation Magazine SEPTEMBER 2006120ElectronicsThe tasks for the electronic system consist of measuring, sens-ing, and control: measuring for evaluation purposes and sens-ing for the control system. It was decided to use a distributed control network, whereeach joint and each foot has its own controller board thatinterfaces the HP5540-series encoders, switches, and sole-noids at the joint. The board as used in the knees and feet isdisplayed in Figure 6. The boards are interconnected using aTWI bus (two-wire interface, also knownas Philips’ I2C bus). Therefore, only fourwires (including power supply) are neededto connect everything on the robot.On the boards, Atmel ATmega8 RISCmicrocontrollers are used. These small micro-controllers are capable of nearly 16 MIPS at16 MHz. Hardware and interrupt service forthe TWI bus is already implemented insidethe controller. The encoders are polled witha relatively high frequency (40 kHz), and thesignals are encoded in quadrature. The maxi-mum resolution for the standard HP55xxseries is 500 ppr (pulses per rotation). Inquadrature, this results in 2,000 ppr, yieldinga resolution of 0.18◦. Angular velocities arecalculated using an Euler differentiation algo-rithm executed in the microcontroller. TheAVR controllers were programmed using apropriarity C compiler from Codevision(http://hpinfotech.ro). The TWI routinesfrom the AVR library from procyon(http://hubbard.engr.scu.edu/avr/avrlib/)were adapted for this compiler.Testing and debugging the TWI systemtook quite some time, especially to get thecorrect responses to fault states on the bus.An Angilent 500-MHz oscilloscope withlogic analyzer and I2C support proved to bea very valuable tool in this process. A typi-cal screenshot while debugging the com-munication between two modules can be seen in Figure 7.For debugging purposes, on each board four light emittingdiodes (LEDs) were placed, along with an RS-232 port,which can be connected to a terminal emulator on a PC.The motor amplifier was designed to be connected by thesame TWI bus, so the same microcontroller was used on thatdesign. For the bridge amplifier itself, a custom H-bridge wasdesigned using IR2110 half-bridge drivers. Safety-monitor-ing, temperature-sensing, and current-limiting functions areperformed by the microcontoller. A central relay can be usedto turn off the power stage. Also, an automatic fuse is addedin the power stage. For noise-reduction spike-suppresiondiodes, big chunky capacitors and a small snubber networkwere added.The motor amplifier board interfaces with an HP55xxsensor mounted on the motor output shaft. The microcon-troller executes a proportional-integral-derivative (PID) con-trol loop at 1 kHz with setpoint and gain values recievedover the TWI bus. The most difficult part regarding the motor amplifierwas designing a printed circuit board (PCB) that couldbe fitted inside the tube with a diameter of 6 cm. Espe-cially the heat sink, relay, capacitors, and power regula-Figure 6. The joint module located on the knee. This boardinterfaces the encoder, controls the knee-lock magnet, and isconnected to the TWI interface using the four colored wires.Figure 5. The new knee-lock mechanism with locking magnet and the old mech-anism with solenoid-driven retracting pin.Figure 4. SolidWorks drawing of the drivetrain.HP EncoderCoupling to Other Leg-Pair Torque SensorMaxon RE40 MotorGearboxLeg AttachmentOldham CouplingSEPTEMBER 2006 IEEE Robotics & Automation Magazine 121tors had to be placed with care. After several attempts,even using cardboard mock-ups, a 5.5-cm-wide and 18-cm-long PCB design was made, containing all compo-nents. Figure 8 shows the breadboard design and thecardboard mockup.Besides the encoders for measuring all angles, a torquesensor was added in the hip joint too. A rotational torquesensor from TRT was incorporated in the mechanicaldesign from an early stage. For this sensor, an interfacecontaining a MAX1452 strain-gauge amplifier and againthe ATmega8 controller was designed. Getting theMAX1452 amplifier stage (a clever chip with a lot of tem-perature and drift compensation possibilities) to workwithout the development kit proved somewhat of a chal-lenge. The ATmega on board fulfilled the tasks of TWIinterface and analog to digital (AD) converter and,using its serial interface, acted as a programmer for theMAX1452 IC.The last microcontroller circuit (bringing the total to astaggering 11 microcontoller boards connected to the samebus) is used as central communication processor and mainwalking algorithm controller. It is dubbed the brain-module.This board is equipped with an ATmega128 running at 16MHz. This controller acts as the TWI bus master, gatheringstatus data from all slaves (joints, torque sensor, motoramplifier) and sending commands to the knee locks andmotor amplifier. The brain-module can send a full robotstate (all angles, switch status, power consumption, andtorque) to a host PC with a rate of 100 Hz for data-loggingpurposes.ExperimentsAt this time (May 2006), the robot has been walking aroundfor almost a year. Most of the walking experiments took placein a cluttered lab where a stretch of 10 m (with the lab dooropen) can be used to let the robot walk. Figure 9 shows anopen-shutter picture of the robot while walking. For the firsttests, a safety line (sort of backyard-zip-line construction) wasused. After some time, most of the students working andwalking with it did not bother to fiddle with the safety lines,which resulted in some collapses. A well-established criterionfor the stability of a walking robot is the distance between therobot and its designer during a test walk (attributed to TadMcGeer). However, the robot still survived all falls, with acouple of bent knee-caps and a broken encoder-casing beingthe main damage. During walking experiments, the main controller executesthe walking algorithm with preset values for gain and set-point, while sending state information at 100 Hz to a host PCperforming the data logging. This setup has proven to be very effective for doing mea-surements. The main conclusion from the measurements, sofar, is that the robot can walk with different gaits at differentspeeds. Regarding energy consumption, cmt-values [1] aslow as 0.06 have been measured, making it very efficient incomparison to other existing walkers.Figure 7. A screenshot of the oscilloscope displaying TWI bus data.Figure 8. A working breadboard design of the 150-W motoramplifier and a cardboard mock-up of the PCB design.Figure 9. A time-lapse shot of the walking robot.IEEE Robotics & Automation Magazine SEPTEMBER 2006122M.S.E. in Robotics at the University of PennsylvaniaThe GRASP Lab at the University of Pennsylvania hasannounced a new Masters of Science and Engineering inRobotics. According to GRASP Director George J. Pappas,the academic mission of this exciting program is the educationof next-generation engineers in the interdisciplinary scienceand technology of robotic and intelligent machines.This multidepartmental, multidisciplinary program pro-vides preparation for industrial jobs in robotics, defense,aerospace, medical device, and automotive industries as wellas various government agencies. In addition, it provides afoundation for doctoral studies in robotics and related fields.More details about the curriculum, application process, anddeadlines, are at: http://www.grasp.upenn.edu/index.html.New Robotics and IntelligentMachines Center at Georgia TechThe College of Computing and College of Engineering at  theGeorgia Institute of Technology has announced the establish-ment of the Robotics and Intelligent Machines center(RIM@Georgia Tech), a new interdisciplinary research centerthat will draw on the strengths and knowledge of roboticsexperts from both colleges. According to robotics industry asso-ciations in North America and Japan, the global robotics mar-ket is expected to significantly expand over the next five years,including gains in both the service and personal robotics fields.Dr. Henrik Christensen, the first KUKA Chair of Roboticsand distinguished professor in the College of Computing,will direct the new research center.DARPA Challenge Moves to the CityThe U.S. Defense Advanced Research Projects Agency(DARPA) announced plans to hold its third Grand Challengecompetition on 3 November 2007. The DARPA UrbanChallenge will feature autonomous ground vehicles execut-ing simulated military supply missions safely and effectivelyin a mock urban area. Safe operation in traffic is essential toU.S. military plans to use autonomous ground vehicles toconduct important missions.DARPA will award prizes for the top three autonomousground vehicles that compete in a final event where theymust safely complete a 60-mi urban-area course in fewerthan 6 h. First prize is US$2 million, second prize isUS$500,000, and third prize is US$250,000. The rules donot restrict the citizenship of any member of the team, exceptthe team leader. All Urban Challenge events and meetingstake place in the United States. Visit the DARPA GrandChallenge Web site: http://www.darpa.mil/grandchallenge.ConclusionsThe design trajectory as described here worked well. The paralleluse of simulation and real-world testing yielded a good workingprototype robot that is robust enough for the daily lab experi-mental work. The matched simulation models proved valuablein testing new controller algorithms and predicting the behaviorof new mechanical additions, such as the compliant feet [7]. Therobot can be used very reliably for doing various measurements.Further ReadingThe design and construction of the robot are discussed in moredetail in the M.Sc. thesis of the author [6], which can be foundat the publication section of http://www.ce.utwente.nl. Thedesign and construction process has also been documented onthe Web, at http://www.ce.utwente.nl/biped.AcknowledgmentsThe design and construction of Dribbel has been a groupeffort: Niels Beekman, Gijs van Oort, Eddy Veltman, andVincent Duindam contributed heavily to this project undersupervision of Prof. Stefano Stramigioli. The work on walk-ing robot systems at the University of Twente is performed atthe IMPACT institute and located at the Control Engineer-ing group of the faculty of Electrical Engineering. KeywordsPassive dynamic walking, bipedal walking.References[1] S.H. Collins and A. Ruina, “A bipedal walking robot with efficient andhuman-like gait,” in Proc. IEEE Int. Conf. Robotics and Automat.,Barcelona, Spain.[2] T. McGeer, “Passive dynamic walking,” Int. J. Robotics Res., vol. 9, no.2, pt. 10.3, p 72, 1990. [3] M. Wisse and J. van Frankenhuyzen, Design and Construction of Mike; a2D Autonomous Biped Based on Passive Dynamic Walking. Kyoto, Japan:AMAM, 2003. [4] S. Stramigioli and H. Bruyninckx, “Geometry and screw theory forrobotics,” presented at ICRA 2001.[5] Controllab products, 20sim, ver3.6., 2006 [Online]. Available:http://www.20sim.com[6] E.C. Dertien, “Realisation of an energy-efficient walking robot,”M.Sc. thesis, University of Twente, The Netherlands, 022CE2005,June 2005. [7] E. Veltman, “Foot shapes and ankle actuation for a walking robot,”M.Sc. thesis, University of Twente, The Netherlands, 002CE2006,May 2006.Address for Correspondence: Edwin Dertien, Control Engi-neering (CE), Faculty of EE-MATH-CS, University ofTwente, P.O Box 217, 7500 AE, The Netherlands. Phone:+31 53 489 2778. E-mail: e.c.dertien@ewi.utwente.nl

Dynamic walking with Dribbel

A bipedal walking robot with efficient and human-like gait,” in

Controllab products, 20sim, ver3.6.,

Design and Construction of Mike; a 2D Autonomous Biped Based on Passive Dynamic Walking.

Foot shapes and ankle actuation for a walking robot,” M.Sc. thesis,

Geometry and screw theory for robotics,” presented at ICRA

Passive dynamic walking,”

Realisation of an energy-efficient walking robot,” M.Sc. thesis,

Dynamic walking with Dribbel

Abstract

Similar works

Full text

Available Versions

University of Twente Research Information