The authors propose a personal model for the calculation of pressure regulator and electromagnetic injection, the volume of fuel injected in cycle and the duration of the injection with the number of rotation at the total full charge load. This kind of mode can be used in the modeling system of electronic gasoline injection monounit or multiunit. To carry out this model it is necessary modeling engines with spark ignition cycle with gasoline injection with a model helping cycle proposed by the authors

Blaga, Vasile

English

Blaga Vasile

University of Szeged

Blaga V., Bara V., Ungur P., Adriana Cäia?. Trifa F.S: THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION Blaga V.,- Bara V., Ungur P., Adriana Cdta$, Trifa F.S, •University of Oradea, Faculty for Protection of Environment ABSTRACT The authors propose a personal model for the calculation of pressure regulator and electromagnetic injection, the volume of fuel injected in cycle and the duration of the injection with the number of rotation at the total full charge load. This kind of mode can be used in the modeling system of electronic gasoline injection monounit or multiunit. To carry out this model it is necessary modeling engines with spark ignition cycle with gasoline injection with a model helping cycle proposed by the authors. l .THE OPTIMIZATION OF THE PRESSURE REGULATOR Pressure regulator maintains constant pressure injection in supplying installation. [3; 5]. Calculation scheme of the pressure regulator is presented in figure 1. Figure I. Scheme of pressure regulator: I-membrane; 2- springs; J- valve; 4- connection to the tank; S- entrance connection; 6- exit connection; 7- housing. Static balance equation of regulator membrane is given by the following relation: Fa+Fga=Fh (1) where: Fa = Ka f ; Fga = J-• pga ; 4 4 and Ka is elastic constant springs; f- spring arrow; D-diameter of the regulator membrane; Fa-power pressure of spring; Fga -pressure power from manifold; pga -pressure from the manifold; pb -gasoline pressure in masterly of the injection; Fb -the gasoline injection power. 17 Blaga V., Bara V., Ungur P., Adriana Cäia?. Trifa F.S: THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION x-D; tt-D; — P* = a/* — After the changing, relation (I) become : or: ph = Kr + p^ : (2) f i i •/" where: K, = ; K, = 1..4 ttD; Kr - is the constant regulator. 2. THE OPTIMIZATION OF THE ELECTROMAGNETIC INJECTION The injector proposed by the author are with electronic command Renix type, with conic top needle with four holes of pulverization or Mono-Motronic with conic top of needle with three holes of pulverization. The volume of gasoline injected in cycle is proportional with the injection pressure and the duration of injection. [3;6]. The section of the passing pulverization hole is determined by the following relation: [6] d [<* A { ß \ ( d ~ ' 1 — + — A = n sa sin — 2 [2 J I 2) \sasinp ) Where: A|-passing section offered by conic top needle: sa-raising up needle; d^-diameter of the needle in top zone; p-cone angle tight; dp-sack diameter. Raising up needle sa is considered to be constant. It was marked with A| the area of the leaking section near the needle top of injector with conic top. A, = f(sa. p. d) = ct A, = 7tfdn - 0,5 sasin(J)sa sin fl/2: sa = 0.15 mm; dP = i... 1.2 mm; P = 6QP. Figure 2. The calculation scheme of electromagnetic injector 18 Blaga V., Bara V., Ungur P., Adriana Cäia?. Trifa F.S: THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION Discharge of gasoline which passes the injector leaking section is calculated by the relation: . ¡ 2 ( P t - P f ) . . . Q„ = / v 4 , — ; (4) V A where hi coefficient of discharge in the section offered by the needle; |i, = 0,8 0.93; Taking in consideration relation (2): (5) V A where: A, is the leaking section at the injector; pb - gasoline pressure at the entrance of injector; p^ - air pressure from the manifold; pb - gasoline density; Kr -constant regulator pressure; Qb- discharge of the gasoline. In the other hands it is lanown from the relation of the discharge definition, that is the leaking fuel volume during a time unit. Maybe written : K mch A"' , & = - = — (6) From the equality of relation (5) and (6) results un duration of the injection, t,: t = mcH I _ "h* j = 1 = mc„ . ' A P.-4-pKr-P* ' * Lo *>acr' ' V A * • L„ m^j A • Lu m^ where ^ is the coefficient which represents the ratio between necessary air quantity for burning moor and the mixed quantity fuel accepted m„d. Results: I, = [ s] (7) H t A , p K r p h where: mcb is the volume of the fuel; maer - the volume of the air aspirated by the engine; ma(j - quantity of mixed fuel admitted; d - proportioning. In figure 3 is represented the variation of the duration of injection t, with the engine speed and the ambient temperature. 19 Blaga V., Bara V., Ungur P., Adriana Cäia?. Trifa F.S: THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION ti, lambda = 1.00 ti [ms] 4.000000 3,000000 2,000000 1,000000 0,000000 Rotation [rot./min] b [ms) 45 to [C] 2000 4000 Rotation [rot/min] • 3,000000-4,000000 • 2,000000-3,000000 • 1,000000-2,000000 m o.oooooo-1,000000 TO = 20,0 C lambda = 1.00 6000 li [ms] n = 5250 lambda = 1.0 __ 3,0001 [ 2.434063 3 2,000-? 1,500-1,000 • 1 0,500 • h— 1 »000 —1— —1 1 1 1 -40 -30 -20 -10 10 to 20 30 40 50 Figure J. The variation of the duration of injection t, with the engine speed and the ambient temperature. 20 Blaga V., Bara V., Ungur P., Adriana Cäia?. Trifa F.S: THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION The working of the curbed engine with lambda sensor and catalyst, makes coefficient X. to be mentioned as close as possible to X=l (stoechiometric dosage). On the base of a personal model the author realized analytic calculation of pressure in the manifold pga and the admission pressure p„, the calculation of engine pressure regulator and the duration t| of the electromagnetic injector. The equation of working engine by spark equipped with electronic engine injection were determined and introduced into the electronic control unit. For the modeling cycle engines with spark ignition with engine injection are noticed the initial dates, pressure expression from un manifold ptfa and the pressure of air at the end of the admission pa, the thermal volume charging qcb, the filling efficiency r)v, the raising ratio of the pressure in a , at volume constant burning, raising ratio of the after burning volume 8, the temperature of the evacuated gasoline Tc, the coefficient of the residual burning gasoline yr, the temperature at the end of the admission T„. All these expression were analytic calculated and correlated among them in order to be introduced into the electronic control unit . The calculator gets the command to repeat this operation till the getting of the imposed error of the engines with spark lighting parameters. It is calculated the mechanical theoretic work proposed Llp, the average pressure proposed plp, theoretical proposed efficiency and the mechanical losses of the cycle. The calculation of engines with spark ignition parameter, was sectioned in 10 proceedings and functions. Near the declared constant values at the beginning of the program, it is considered as initial dates, presumed to be known choosing arbitrary from the statistical dates of engines with spark ignition cycle: Ta0=322 K; ^ = 2 5 3 0 K; Tuo =2660 K and kfo =1,3; kv0 =1,3; ku0 =1,2; kdo=l,3; keo=l,3; without them are not possible to calculate in general way all others coefficients and the other temperature and the physical size which characterize the cycle. In this way the size above will play the parameter role, variable will the temperature in which thermal process evaluate. These temperatures depend on the adiabatic coefficients which in fact are stability by going though many times of the cycle until these coefficients become constant with 0,000009 error. This exit decision from the cycle for a certain revolution is given by the diminish of the constant error of temperature Ta under 1,5 K. 3.CONCLUSIONS It is conceived the calculation of the pressure regulator and of the electromagnetic injector. It was made the calculation of the injection duration t, with the engine speed and load which represents the model proposed by the author. It was effectuated an engine with spark ignition program for the calculation of parameters with the gasoline injection with the under- program: 21 Blaga V., Bara V., Ungur P., Adriana Cäia?. Trifa F.S: THE OPTIMIZATION OF THE ELECTRONIC CONTROLLED INJECTION - the calculation program of engines with spark ignition parameters (depending on n and I at to=-35...+45°C and p0= I -102 kPa) [3]. - the calculation program of engines with spark ignition parameters (depending on n and ^ at X=l and p o = H 0 : kPa) presented in annex B;[3). REFERENCES: 1. Apostolescu. N. and Chiriac. R. , Process of burning in driving with inwar alight.The Technical Edition.Bucharest 1998. 2. Bäjagä, N. , Driving with inward alight. The Didactic and Pedagogical Edition. Bucharest 1996. 3. Blaga. V. , The contribution at modeling of gasoline injection at M.A.S. Work of doctor's. The Technical University of Cluj-Napoca 2000. 4. Blaga, V., The dynamic of car. The University Edition 0radea,2005. 5. Blaga, V.,Engine with gasoline injection, The University Edition 0radea,2005. 6. Delanette, M., Les Motors a injection. Edition Tehniques pour L'automobil et L'industrie, iunie, 1989. 7. Negrea, V. D. , The combating of medium poluttion in motor vehicle. The Technical Edition, Bucharest, 2000 8. Turcoiu. T., Boncoi, J. §i Time, AI, Equipment's from injection for engine with internal burning. The Technical Edition, Bucharest 1987. 22 

The optimization of the electronic controlled injection

http://acta.bibl.u-szeged.hu/11755/1/engineering_2007_017-022.pdf

The optimization of the electronic controlled injection

Abstract

Similar works

Full text

Available Versions

University of Szeged