International audienceThe OMEGA group at LAL has designed 3 chips for ILC calorimeters: one analog (SPIROC) and one digital (HARDROC) for the hadronic one and also one for the electromagnetic one (SKIROC). The readout and the management of these different chips will be explained. To minimize the lines between the ASICs and the DAQ, the readout is made thanks to 2 lines which are common for all the chips: Data and TransmitOn. As the chips are daisy chained, each chip is talking to the DAQ one after the other. When one chip has finished its readout, it starts the readout of the chip just after. Moreover, during this readout, only the chip which is talking to the DAQ is powered: this is made thanks to the POD (Power On Digital) module in the ASIC. In the ILC mode, readout sequence is active during inter bunch crossing (like ADC conversion). Another chip designed for PMM2 R&D program (PARISROC) integrates a new selective readout: that's mean only hit channels are sent to the DAQ in a complete autonomous mode

de La Taille, C.

Dulucq, F.

Martin-Chassard, G.

HAL-IN2P3

”ROC” Chips ReadoutF. Dulucq, C. De La Taille, G. Martin-ChassardTo cite this version:F. Dulucq, C. De La Taille, G. Martin-Chassard. ”ROC” Chips Readout. Dho E. TopicalWorkshop on Electronics for Particle Physics (TWEPP-09), Sep 2009, Paris, France. Cern,pp.491-494, 2009. <in2p3-00425501>HAL Id: in2p3-00425501http://hal.in2p3.fr/in2p3-00425501Submitted on 21 Oct 2009HAL is a multi-disciplinary open accessarchive for the deposit and dissemination of sci-entific research documents, whether they are pub-lished or not. The documents may come fromteaching and research institutions in France orabroad, or from public or private research centers.L’archive ouverte pluridisciplinaire HAL, estdestine´e au de´poˆt et a` la diffusion de documentsscientifiques de niveau recherche, publie´s ou non,e´manant des e´tablissements d’enseignement et derecherche franc¸ais ou e´trangers, des laboratoirespublics ou prive´s.Presentation of the “ROC” Chips Readout F. Dulucq a, C. de La Taille a, G. Martin-Chassard a,  a IN2P3/LAL/OMEGA, UPS11-Bat200, Orsay, France  dulucq@lal.in2p3.fr  Abstract The OMEGA group at LAL has designed 3 chips for ILC calorimeters: one analog (SPIROC) and one digital (HARDROC) for the hadronic one and also one for the electromagnetic one (SKIROC). The readout and the management of these different chips will be explained. To minimize the lines between the ASICs and the DAQ, the readout is made thanks to 2 lines which are common for all the chips: Data and TransmitOn. As the chips are daisy chained, each chip is talking to the DAQ one after the other. When one chip has finished its readout, it starts the readout of the chip just after. Moreover, during this readout, only the chip which is talking to the DAQ is powered: this is made thanks to the POD (Power On Digital) module in the ASIC. In the ILC mode, readout sequence is active during inter bunch crossing (like ADC conversion). Another chip designed for PMM2 R&D program (PARISROC) integrates a new selective readout: that’s mean only hit channels are sent to the DAQ in a complete autonomous mode. I. GENERAL OVERVIEW A. Some ROC chips and their applications 1) MAROC: MAROC (Multi-Anode ReadOut Chip) is designed to read multi-anode photomultipliers [1] of the ATLAS luminometer made of Roman pots (Figure 1).  Figure 1: MAROC chip layout 2) SKIROC: SKIROC (Silikon Kalorimeter ReadOut Chip) has been designed to read-out the upcoming generation of Si-W calorimeter featuring ILC requirements (Figure 2).  Figure 2: SKIROC chip layout 3) HARDROC: HARDROC (HAdronic Rpc Detector ReadOut Chip) is the front end chip [2] designed for the readout of the RPC or GEM foreseen for the Digital HAdronic CALorimeter of the future ILC (Figure 3).  Figure 3: HARDROC chip layout 4) SPIROC: SPIROC (Silicon Photomultiplier Integrated ReadOut Chip) is a dedicated front-end electronics [3] for an ILC prototype of hadronic calorimeter with Silicon photomultiplier readout (Figure 4).  Figure 4: SPIROC chip layout 5) PARISROC: PARISROC (Photomultiplier ARray Integrated in Sige ReadOut Chip) is the front end ASIC designed for the PMM2 R&D project dedicated to neutrino experiments (Figure 5).  Figure 5: PARISROC chip layout B. High level working The ROC chips can be divided in 2 groups: analog and digital ones. It depends if the signal from the detector is first stored into an analog way or directly in a digital way. For analog chips, discriminated analog signals are first stored into an analog memory (the SCA: switched capacitor array) and then converted into digital words thanks to an ADC. These digital values are stored in a RAM to be readout at the end of the acquisition cycle. For digital chips, the ADC is not needed as data are directly saved into the RAM. This is shown in next Figure 6.  SwitchedCapacitorArrayRegisters100101110101ShiftRegisterDAQAnalog to Digital ConverterSlow shaper signalAcquisition ConversionRead-OutTop ManagerTDC ramp signal Figure 6: High level working C. Main analog block These analog chips are based on Switched Capacitor Array (SCA). The number of channels managed can be up to 64. Fine time measurement is available depending on the application and experiment. The main architecture of analog part is given below in Figure 7.  T&H CellADC Rampx1x1x1x1TDC RampSlow ShaperT&H CellT&H CellT&H CellTimeEndConversionChargeEndConversionRead switches Figure 7: Main analog block Figure 8 is an example of the behaviour of a “Track & Hold Cell” which allows to lock the capacitor value at the maximum of the analog signal.  Slow shapersignalTrigger CalibrDelayedT&HTrackHoldTDC rampsignal Figure 8: Behaviour of Track and Hold cell II. TIMING CONSIDERATIONS A. Global overview Depending on the application, acquisition module is not active all the time. For example, in bunch crossing train sequence like in the future ILC, acquisition is stopped after each train (Figure 9). This is the case for SKIROC, SPIROC and HARDROC chips for ILC calorimeters.  Acquisition Conversion Read-OutBunch Crossing TrainTimeStartConversion_bStartAcquisitionStartRead-OutChip_SatEndRead_Out Figure 9: ILC sequences In neutrino experiment, acquisition is never stopped. This is the case for PARISROC chip which can handle an acquisition active all the time. During its conversion and readout phases, discriminated analog signals can be stored in the SCA if it is not full. B. Future ILC requirements Future ILC is based on a 200ms bunch crossing train period (Figure 10). For the front end electronics, the digital part of acquisition is active only during the bunch crossing and the conversion and the readout are active during inter bunch crossing. Acquisition Conversion Read-Out AcquisitionBunch Crossing TrainTimeDigital PartPhasesBunch Crossing Train  Figure 10: ILC timing requirements Acquisition and conversion modules are active at the same time for all the ASICs. That’s why the power on can be managed by the DAQ. But, as the readout is daisy chained, the power on should also be managed by the daisy chain. On the table 1 below are represented the maximum duration of each phase.  For each cycle of 200ms, one ASIC should be powered only 8 ms (4% of cycle). This will allow to meet power budget. POD module was designed to fulfil this requirement for the digital part. Table 1: ASIC timings Phase Duration Comments Acquisition 1ms Bunch crossing train duration Conversion 3ms Worst case (32 conversions) Readout 4ms 5 MHz readout clock  III. POWER ON DIGITAL (POD) MODULE A. Block diagram Power On Digital (POD) module has been design to meet ILC power budget for front end electronics. Il allows to start and stop clocks depending on the 3 phases (acquisition, conversion and readout). Additionally with start/stop of the clock, it manages the LVDS receiver bias current: its power supply. The combination of clock gating and LVDS management allows to meet the power budget of the ILC (see Figure 11).  LVDSReceiverEnable Clockfor Acquisition andConversionClkOutPowerOnDigitalStartReadOutEndReadOutStartReadOutIntStartLVDSClkinEnable ClockforReadoutRstbClkinClkOutPOD moduleEnableEnableClock Figure 11: Block diagram The POD module is divided in 3 parts. One is activated and managed by the DAQ during common phases: acquisition and conversion. The second one is set during the readout by the daisy chained token. The last one manages the LVDS receiver. B. Layout POD has been layouted with standard 3-b cells from AMS (Austria Micro System). The main layout features are given after in Table 2.  Table 2: ASIC timings Area 120 um x 80 um Flip flop 8 FF Layout 2 metals (M1 and M2) Frequency Up to 40 MHz  Besides, power supply pins are accessible at each corner of the module (Vdd, Gnd and Vss). This module has been integrated in HARDROC chips at revision 2 and higher (Figure 12).   Figure 12: POD layout C. Detailed working The timing diagram given below (Figure 13) represents the complete sequence driven by the DAQ. It shows the 3 sequences and how they are managed. The “clock stopped” zones corresponds when POD is off (not scaled). As mentioned above, it represents 96% of time and allows to meet power budget requirement (25 uW per channel). For each phases, clock is started asynchronously, enabled and stopped synchronously (idle state at logic ‘0’).  StartConv_bStartAcqtStartRead-OutChip_SatEndRead_OutAcquisition Conversion Read-OutResetbPowerOnDigitalClockStartClockStartCalibrated(LVDS start time)From DAQFrom daisy chainFrom ASICGeneratedSROFrom PODClock StoppedClock Stopped Figure 13: Detailed working 1) Acquisition and conversion phases PowerON is set during the reset phase before each acquisition. It allows to start the LVDS receiver and consequently the clocks. When clocks are established, reset can be released; this is done after reset startup time which is about 200 ns. That’s why reset duration must be longer than LVDS wakeup time (Figure 14). ResetbPowerOnDAQCtrlAcqt  Figure 14: Start of acquisition PowerON is released at the end of the conversion. It is synchronized internally to properly stop the clocks. Effective PowerOn release is done after few clock ticks (Figure 15).  PowerOnDAQPowerOnFast ClockPowerOnSlow Clock  Figure 15: Stop of acquisition and conversion PowerON is asynchronously set by the DAQ during the reset state and it is synchronously released by the POD in each chips. 2) Readout phase PowerON during daisy chained readout is done by the previous chip thanks to its calibrated EndReadout which is the StartReadout of the chip just after it. This signal allows to start LVDS receiver and then synchronously the clocks. Finally, it generates an internal StartReadout for state machines (Figure 16). StartReadOutStart LVDSReceiverStart FastClockStart SlowClockInternal StartReadOut  Figure 16: Start of readout At the end of the readout, clocks and LVDS receivers are stopped synchronously (Figure 17). Effective PowerOn release is done after few clock ticks (2-3).  LVDS +Fast ClockLVDS +Slow ClockEndReadOut Figure 17: Stop of readout IV. PARISROC NEW READOUT Parisroc [4] integrates a state machine to control the 3 phases: it allows to have a complete autonomous working. Moreover, compare to other ROC chips, it integrates a new channel management: they are completely independent. That’s mean, when 1 channel is hit, ADC conversion is started and then the readout of this channel. The readout will only treat hit channels, that’s why this module tags each frame with its channel number. During conversion and readout, acquisition is never stopped: triggers are stacked into SCA and treated as soon as possible (Figure 17).  12 bits ADCCounterSCA 1 ChnFIFO managementof SCAState Machine24 bits TimestampCounterRead / WriteSCA triggeredAnalogValueADC RampReadoutmodule32 Registersof 24 bits32 Registersof 12 bitsTop ManagerStart RampDataOutputEndConversion Figure 18: Block diagram V. REFERENCES [1] Barrillon P. et al., "MAROC: Multi-Anode ReadOut Chip for MaPMTs", Nuclear Science Symposium Conference Record, 2006. IEEE, vol.2, pp.809-814, Oct. 29 2006-Nov. 1 2006 [3] Seguin-Moreau N. et al., "HARDROC1, Readout chip of the Digital Hadronic Calorimeter of ILC", TWEPP 2007 Conference Proceedings [3] Raux L. et al., "SPIROC (SiPM Integrated Read-Out Chip): Dedicated very front-end electronics for an ILC prototype hadronic calorimeter with SiPM read-out", TWEPP 2008 Conference Proceedings [4] Dulucq F. et al., "Digital part of PARISROC: A photomultiplier array readout chip", Nuclear Science Symposium Conference Record, 2008. NSS 08. IEEE, pp.2002-2005, 19-25 Oct. 2008    

“ROC” Chips Readout

Abstract

Similar works

Full text

Available Versions

HAL-IN2P3