The connection of oil volumes of transformer and tap-changer offers several advantages and savings, such as a simplified piping construction and the omission of a second oil conservator. Combined oil volumes shall only be applied to vacuum type tap-changers, and the most simple, easy-to-apply and cost-effective solution is achieved by using the connecting bone

Rainer Frotscher

English

Hrčak - Portal of scientific journals of Croatia

For many applications, there is no technical reason anymore to keep the oil volumes of a transformer with vacuum type OLTC separatedCOLUMN20    TRANSFORMERS  MAGAZINE  |  Volume 4,  Issue 2Common  oil expansion tank for transformers and  tap-changers1. IntroductionOn-load tap-changers (OLTCs) feature an own oil compartment which accommodates the diverter switch or selector switch and separates the tap-changer oil from the transformer oil. This strict separation is necessary for conventional diverter and selector switches, because the arc-breaking operation deteriorates the oil in the tap-changer compartment severely and produces huge amounts of particles, soot and gases. It must be ensured that these deterioration products do not contaminate the transformer oil. For this reason, the active IEC and IEEE tap-changer standards [1], [2] require a tightness test or container integrity test for the diverter switch or selector switch.Rainer FROTSCHERwww.transformers-magaz ine .comPhoto courtesy of Siemens  21 2. Gas exchange between connected oil volumesConnected oil volumes are only reason­ably applied to in­tank type OLTCs. Compartment type OLTCs usually don’t feature an oil expansion tank because they compensate the thermal oil expansion by using a gas space underneath the tank cov er (see [6], page 26, Figure 1). They are not completely filled with oil, so the con­nection with the transformer oil does not offer concrete benefits.In­tank type OLTCs must always be completely filled with oil to ensure that the drive mechanism and the phase­to­ground insulating distance are covered with oil. This requires a separate expan­sion tank for the OLTC oil, often called con servator, to compensate for the thermal volume dilatation. This conservator can be omitted if there is a permanent connec­tion between tap­changer oil and trans­former oil. Now, it would be interesting to know how the oils intermix. Be it that a failure develops inside the tap­changer, dissolved gases will differ more or less si­gnificantly from the gases in the trans­former. With a permanent connection, they can be introduced in the transformer oil and may influence transformer DGA.To investigate the dimension of liquid and gas exchange, a test has been per formed, using a model setup with two oil compart­ments. A small tank (65 litres, “tap­chan­ger”) was mounted in a bigger tank (1185 litres, “transformer”). Both oil volumes were interconnected by a pipe elbow (see Fig. 2) and filled with degassed mineral oil. The “tap­changer” oil was then inocu­lated with 150 ppm C2H2. The resistor in­side the “tap­changer” compartment was heated by current impulses which were controlled by an electronic AC p ower supply. The current impulses simulated the switching operations and caused well­defined fast temperature rises, represent­ing the typical resistor heating of a tap­changer under network load (ΔT 160 K) and under 1.5 times overload (ΔT 250 K). 300,000 current impulses were applied in total. The maximum oil temperature in both oil compartments was limited to 50 ing or arcing gases. Inside the transformer, capacitive switching arcs of low energy must be broken when the change­over selector is operated. They produce low amounts of arcing or sparking gases which, in the majority of cases, are not visible in the transformer DGA. The ageing impact of both arcing/sparking processes on the oil is negligible. As a result, the OLTC oil is only thermally aged by the heating of transition resistors. Their thermal impact roughly corresponds to the impact of wast e heat from the transformer windings on the transformer oil. So, it can be stated that the stresses on OLTC (vacuum type) and transformer oil are very similar; they cause similar compositions and amounts of dissolved gases and so allow an exemption from the above mentioned tightness or container integrity test.To put it in a nutshell: if vacuum type tap­changers are used, the conditions for the tap­changer oil are very similar to the con­ditions for the transformer oil. For many applications, there is no technical reason anymore to keep the two oil volumes sepa rated. So, what prevents us from join­ing the two oil expansion tanks (and so the oil volumes)? It simplifies oil handling and offers savings.This test is only passed if the tap­changer oil compartment is pressure tight and gas tight. Nevertheless, there is a huge num­ber of older units installed in the field which may show some leakage. This does not mean that the tap­changer oil mixes with the transformer oil to a big extent, but at least dissolved gases are able to t ravel between the two oil volumes and so may influence transformer DGA. There are basically three pathways which are used by tap­changer gases to diffuse into the transformer oil: via a non gas tight oil compartment (as seen for some old press paper cylinders), via leaking gaskets, or via a common air space in the oil expan­sion tank; see Figure 1. The latter case is often not considered, but it appears quite often, e.g. in Eastern Europe. Dissolved tap­changer gases outgas to the air space in the expansion tank and dissolve again in the transformer oil, depending on the ruling gradients in partial pressure. With respect to such cases, IEC60599 specifies higher values for acetylene in the trans­former oil (for typical gas concentration rates and typical rates of gas increase) for so­called “communicating OLTCs” [3].Modern OLTC models use vacuum inter­rupters which encapsulate the switching arcs and so prevent the oil from pyrolytic degradation. Carbon particles are no more produced, only some sparks of low energy occur, due to some current commutation between the OLTC­internal current paths during the switching process. These sparks only produce very low amounts of spark­COLUMN The conditions for the vacuum type tap-changer oil are very similar to the conditions for the transformer oilFigure 1. Different pathways for gas contamination of the transformer oil by OLTC gases22    TRANSFORMERS  MAGAZINE  |  Volume 4,  Issue 2cross sections are very slow and can be ne­glected.In the theoretic case of a complete inter­mixing of “tap­changer” oil and “trans­former” oil, 150 ppm C2H2 in the “tap­changer” oil would dilute to about 8 ppm C2H2 in the “transformer” oil (150 · 65/1185 ppm). For real applications, the ratio of oil volumes is much bigger than in the test (about 1:100). Furthermore, 150 ppm C2H2 should not occur in a vacuum type °C by cooling helixes to minimize a po­tential self­gassing activity of the oil.The heat energy introduced by the resistor heated the “tap­changer” oil and so caused a thermal expansion. With each impulse, the “tap­changer” oil volume expanded for approximately 1 ml. A temperature rise of 25 K (difference between ambient temperature 25 °C and maximum oil tem­perature 50 °C) caused a volume increase of approximately 1.2 l. This amount of oil moved through the pipe elbow into the transformer during the heating period and was drawn back during the cooling period. In total, 17 heating/cooling cycles within one­month time were performed, causing a permanent oscillation of 1.2 l of oil, the total transported oil volume sum­med up to round about 20 l. Regular oil samples were taken from both oil compartments and DGAs were per­formed. After the test, the “tap­changer” oil showed a slight increase of the heat­ing gases CH4, C2H4, C3H8 and C3H6, between 1 and 7 ppm for each gas. In the transform er oil, the increase of dissolved heating gases was below 1 ppm and no C2H2 was detected.It can be assumed that the transported oil volume did not fully exchange with every cycle, which means that transformer oil and tap­changer oil keep rather separate, as long as a 1” pipe or a similar connec­tion with small cross section is used. For a network transformer, the oil expansion of the OLTC oil which is caused by resis­tor heating and daily temperature cycles of the transformer is quite low. Diffusion processes of dissolved gases through small tap­changer in regular service. Such high C2H2 amount clearly indicates a malfunc­tion.As a conclusion, it can be stated that it is very unlikely to disturb transformer DGA by OLTC gases, as long as the cross section of the connection is small. Several pilot applications and field studies [4], [5] have verified this.3. Implementations of connected oil volumesThe realized applications use different solutions to connect the oil volumes of tap­changer and transformer. They can be applied to free­breathing applications as well as to sealed applications. Sealing of (vacuum type) tap­changers was dis­cussed in [6]. Figure 3 shows a possible solution for free­breathing applications. The pipe from the tap­changer compartment, which nor­mally leads to the OLTC expansion tank, is connected directly to the pipe which leads from the transformer to the expan­sion tank. With this, the separate chamber in the expansion tank for the OLTC can be omitted, including its oil level indica­tor and dehumidifying cartridge. It has to be considered that, in case of a beginning fail ure inside the transformer or OLTC, Figure 2. Test setup for gas exchange with connected oil volumesFigure 3. Connected oil volumes for free-breathing applicationsSeveral pilot applications and field studies have verified that it is very unlikely to disturb transformer DGA by OLTC gases, as long as the cross section of the connection is smallwww.transformers-magaz ine .com   23 the fault gases cannot be explicitly assi­gned to the transformer or the OLTC. If this is a problem, an alternative piping can be used which connects the OLTC pipe to the expansion tank behind the Buchholz relay (see Fig. 3). This also minimizes a possible gas exchange between the two oil volumes. Concerning sealed applications, the applied sealing method is often unknown to the tap­changer manufacturer, so the proper function of the oil­flow relay cannot be guaranteed. If the OLTC protection concept for sealed tap­changers, see [6], is applied in com bination with the piping shown in Figure 3, the solution according to Figure 4 is achieved. The concept pro­vides a Pressure Relief Device (PRD, mandatory) and a Buchholz relay as gas warning device (optional). If a separate tap­changer gas warning is not required, the Buchholz relay of the transformer can adopt this function (see Fig. 5). It has to be pointed out that, in this case, the origin of possible free gases cannot be located. Anyhow, the OLTC protection concept for sealed applications is fully supported.All these solutions can be found in the field and they are working reliably.4. Minimized pipingFigure 5 represents an optimized imple­mentation which fully supports the pro­tection concept for sealed tap­changers. Several years of field experience have shown that vacuum type tap­changers do not produce any free gases during nor­mal service. Courageous users may now go without the OLTC gas warning, as it is just optional, and not a requirement. The shortest possible connection between the two oil volumes is a connection between the two pipe flanges “E2 and “Q” (see Fig. 6) on the OLTC head. “E2” opens out into the transformer tank; “Q” ends in the OLTC compartment. The connection can be realized by a metal plate (“con-necting bone”, named after its shape), which features a through­hole between the two pipe flanges. The pipe flanges are both closed by blind covers. The connec­tion can be closed by a valve screw with two gaskets (see Fig. 7), in case the OLTC must be opened for inspection or main­tenance. The valve screw must always be open during normal operation to allow a compensation of thermal oil expansion into the transformer tank. The connec­ting plate can be applied to free­breathing and sealed applications in the same way. Note that, with open connection, the oil pres sure inside the OLTC always exactly equals the pressure inside the transformer tank, which is determined by the height of the oil expansion tank (free­breathing) or the preset system pressure (sealed).Diffusion processes of dissolved gases bet­ween the two oil volumes will be very low and thus are negligible, due to the small diameter of the through­hole in this ex­ample.As there is no pipe leading from the OLTC to an oil expansion tank (or the trans­former tank), the standard oil­flow relay cannot be applied anymore as protective device for the OLTC. As a substitute, a PRD must be applied, like in the pro­tection concept for hermetically sealed OLTCs. The PRD triggers the circuit breaker in case of an internal flashover or severe malfunction of the tap­changer mechanism. This is necessary because a sudden rise in pressure cannot be broken down fast enough by the oil flow through the thin via in the connecting plate. Courageous users may now go without the OLTC gas warning, as it is just optional and not a requirementFigure 4. Connected oil volumes for sealed applications; principal schematicFigure 5. Connected oil volumes for sealed applications; optimized solution24    TRANSFORMERS  MAGAZINE  |  Volume 4,  Issue 2COLUMNAuthor Dipl.-Ing. (TU) Rainer Frotscher is working for Maschinenfabrik Reinhausen (MR) in Regensburg/Germany as expert for special tap­changer applications. For many years, he has been working in the R&D department on manifold projects and studies to promote the technology of on­load tap­changers. His area of expertise is the applicability of alternative liquids and DGA for tap­changers. As core competence manager for insulating liquids and gases, he now develops the knowledge within the Reinhausen Group concerning the interaction of solid, liquid and gaseous insulating materials. As a member of CIGRE and DKE, he has done multiple publications and contributes to several working groups in CIGRE, IEEE and DKE. Dipl.­Ing. Frotscher was born in Bremen, Germany on March 4, 1960. He received his Master’s Degree in Electrical Engineering from the Technical University of Munich where he wrote his thesis in high­voltage engineering.Phone :  +49 (0) 941/4090­4136Fax :      +49 (0) 941/4090­4005Email :  r.frotscher@reinhausen.comAddress :  Maschinenfabrik Reinhausen GmbH  Falkensteinstraße 8, 93059 Regensburg, GermanyConclusionThe connection of oil volumes of trans­former and tap­changer offers several ad­vantages and savings, such as a simplified piping construction and the omission of a second oil conservator. There are different solutions available, depending on the con­struction of the transformer oil expansion unit. This can be a rubber bag, a nitrogen reservoir or an expanding radiator. The most simple, easy­to­apply and cost­effective solution is achieved by using the connecting bone. Note that all solutions for combined oil volumes shall only be applied to vacuum type tap­changers. Even if it is not really necessary, the tap­changer oil compartments will still be manufac tured pressure tight and gas tight, no matter how the connection is executed.5. Literature[1] IEC 60214­1, Tap-changers – Part 1: Performance requirements and test methods[2] IEEE C57.131, IEEE Standard Re-quirements for Tap Changers[3] IEC60599, Mineral oil-filled elec-trical equipment in service – Guidance on the interpretation of dissolved and free gases analysis[4] T. Stirl, J. Harthun, ALSTOM, R. Frotscher, MR, Offshore Use – A Challenge for the Transformer, Stuttgarter Hochspan­nungssymposium, Germany, 2012[5] R. Frotscher, MR, J. Findeisen, S IEMENS AG: Gemeinsamer Ölhaus-halt von Transformator und Stufen-schalter, ETG­Fachtagung VDE­Hoch­spannungstechnik, Berlin, 2016[6] R. Frotscher, Hermetical sealing of transformers and tap­changers, Trans-formers Magazine, Volume 4, Issue 1, January 2017The most simple, easy-to-apply and cost-effective solution is achieved by using the connecting boneFigure 7. Connected oil volumes with connecting plate (section)Figure 6. Connecting plate on OLTC head cover for connecting the oil volumes of trans-former and vacuum type tap-changerwww.transformers-magaz ine .com   25 

Common oil expansion tank for transformers and tap-changers

Abstract

Similar works

Full text

Available Versions

Hrčak - Portal of scientific journals of Croatia

HRČAK - Portal of Croatian Scientific and Professional Journals