The Fermilab Main Injector is moving toward providing 400 kW of 120 GeV proton beams using slip stacking injection of eleven Booster batches. Loss of 5% of the beam at or near injection energy results in 1.5 kW of beam loss. A collimation system has been implemented to localize this loss with the design emphasis on beam not captured in the accelerating RF buckets. More than 95% of these losses are captured in the collimation region. We will report on the construction, commissioning and operation of this collimation system. Commissioning studies and loss measurement tools will be discussed. Residual radiation monitoring of the Main Injector machine components will be used to demonstrate the effectiveness of these efforts

/Fermilab

Adamson, Philip

Brown, Bruce

Capista, David

Drozhdin, A.I.

Johnson, David E.

Kourbanis, Ioanis

Mokhov, Nikolai V.

Morris, Denton K.

Rakhno, Igor

Seiya, Kiyomi

Sidorov, Vladimir

UNT Digital Library

FERMILAB MAIN INJECTOR COLLIMATION SYSTEMS: DESIGN,COMMISSIONING AND OPERATION ∗Bruce Brown, Philip Adamson, David Capista, Alexandr I. Drozhdin, David E. Johnson,Ioanis Kourbanis, Nikolai V. Mokhov, Denton K. Morris, Igor Rakhno, Kiyomi Seiya,Vladimir Sidorov, Guan Hong Wu and Ming-Jen Yang † ,Fermilab, Batavia, IL 60510, USAAbstractThe Fermilab Main Injector is moving toward providing400 kW of 120 GeV proton beams using slip stacking in-jection of eleven Booster batches. Loss of 5% of the beamat or near injection energy results in 1.5 kW of beam loss.A collimation system has been implemented to localize thisloss with the design emphasis on beam not captured in theaccelerating RF buckets. More than 95% of these lossesare captured in the collimation region. We will report onthe construction, commissioning and operation of this col-limation system. Commissioning studies and loss measure-ment tools will be discussed. Residual radiation monitoringof the Main Injector machine components will be used todemonstrate the effectiveness of these efforts.ACHIEVING HIGH INTENSITYThe Fermilab Main Injector provides high intensity 120GeV proton beams for production of anti-protons andneutrinos[1]. Protons are injected from the 8 GeV Boosterwhich can provide intensities > 5 × 1012 per batch. Thegaps needed for injection and extraction limit one to accel-eration of 6 batches of Booster length. To increase the in-tensity above 30×1012 requires stacking. Slip-stacking[2]has been developed to permit acceleration of 11 Boosterbatches. Operation with 2.2 second cycles has producedmore than 350 kilowatts of 120 GeV beam power with in-tensity limited by operational loss limits.The most significant losses are directly related to the lim-itations of the slip stack process. Limits to the RF bucketsizes during slipping are specified by the available momen-tum aperture while the momentum spread of the Boosterbeam includes tails beyond that which can be captured.This beam which is uncaptured during the slipping processmay be captured in unwanted locations (kicker gaps) whenthe acceleration RF system is turned on or it may remainoutside the RF bucket and not be accelerated. The MainInjector Collimation System is designed to efficiently ab-sorb losses due to unaccelerated beam.COLLIMATION SYSTEMAs the acceleration ramp begins, the captured beam isaccelerated on the central orbit while the uncaptured beam∗Operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.† bcbrown@fnal.govfollows the dispersion orbit at greater and greater momen-tum offset. However, the straight sections, where one canplace absorbers, were designed with low dispersion. Thecollimation system is designed using secondary collima-tors in the MI300 straight section and a primary collima-tor in the last half cell (MI230) ahead of that region wherethere is sufficient dispersion. The 0.25 mm Tungsten pri-mary collimator is set to define the momentum aperturewith a vertical edge. The secondary collimators are lo-cated downstream at horizontal phase advances of 156o,245o,423o and 476o. The secondary collimators are thick-walled stainless steel vacuum boxes surrounded by a mas-sive absorber system. Each of them is placed so that thecirculating beam is in a corner and the beam scattered bythe primary collimator will strike one radial and one verti-cal aperture limit.The collimation design was based on an extensive sim-ulation of slip stacking in the Main Injector[3] using theSTRUCT code. We found that, after careful description ofthe lattice and the slip stacking process, the time structureof the loss and the quantity of beam lost could be simulated.However, simulation with only the linear fields predictedlosses only at points of high dispersion. Simulation includ-ing the measured higher harmonic components of the mag-netic fields predicted losses at transfer points (Lambertsonmagnets) where the aperture restriction is mostly verticaland dispersion is low. The comparison with losses duringslip stacking operation was much better. The above colli-mation concept was then added to the simulation and opti-mized. It predicted that particles lost due to the uncapturedbeam would be absorbed by the collimation system (fromthe primary collimator to the end of the MI300 straight sec-tion) with more than 99% efficiency.The collimation system was installed in the 2007 Fer-milab Facility Shutdown and was ready to begin com-missioning in November 2007. The hardware[4][5] andcommissioning[5] have been described previously. Sincethe MI300 straight section also includes the Recycler Elec-tron Cooling system, one wishes to limit the radiation ex-posure of those devices. In order to limit radiation of thematerials outside of the concrete tunnel enclosure, the sec-ondary collimators were constructed to fill the availabletransverse aperture. The length is sufficient to capture thebulk of the induced shower. The face of the collimator isplaced parallel to the centerline of the straight section whilea taper on the upstream collimator end permits the absorp-tion of the shower with minimum outscattering.Figure 1 pictures the 20-Ton secondary collimator atFERMILAB-CONF-09-167-ADFigure 1: 20-Ton Secondary collimatorMI301. The residual radiation in the aisle is reduced byaddition of marble to shield the MeV gamma rays due toactivation of the steel. The motion system provides hori-zontal and vertical positioning with 25 µm step size. Thebeam pipe adjacent to the downstream end of the collima-tor and again upstream of the next corrector magnet hasbeen provided with a ‘mask’ by surrounding the pipe withiron blocks which are in turn surrounded by concrete ormarble. Outscattered beam remanents and shower tails arecaptured by these devices. This system was not providedfor the third collimator as low losses was expected fromuncaptured beam but high loss is observed before accel-eration and as a result, the next corrector magnet is veryradioactive. Comparison with comparable locations sug-gests that these masks provide about a times ten reductionin residual activation. The upstream end of the collimatorsis shielded by a polyethylene block to reduce the flux ofneutrons which impact the nearby quadrupole magnet.COMMISSIONING AND LOSSMEASUREMENTA kicker near the middle of the MI300 straight section isemployed to transfer anti-protons from the Main Injector tothe Recycler and back. The positioning of the collimatorsis restricted by the orbits employed for these transfers. Inorder to employ the collimators, a time bump distorts theclosed orbit. This orbit is designed so that, at the desiredemittance boundary, the edge of the beam is parallel tothe collimator, causing unwanted particles to strike the up-stream tapered portion. Since no dipole corrector magnetswere added for the collimation project, there is only a min-imal set and the possible orbit offsets at the four secondarycollimators are coupled. Some flexibility is achieved byemploying correctors outside of the collimation region toinduce an incoming distortion.The Main Injector is equipped with a loss monitor sys-tem consisting of sealed glass ion chambers filled with ar-gon. New electronics was commissioned in 2007 to pro-vide high resolution recording and flexible readout. Appli-cations to display this data for monitoring and studies hasbeen developed in order to optimize collimation.0.3 0.31 0.32 0.33 0.34 0.3505001000150020002500LQ230 LossLQ303 LossUncaptured Beam Loss0.3 0.31 0.32 0.33 0.34 0.358.58.68.78.88.999.1Beam IntensityMomentumFigure 2: Loss monitor readings, momentum and beam in-tensity during uncaptured beam loss on PBar productioncycle. Loss at primary and one secondary collimator areshown. Loss peak occurs when captured beam has beenaccelerated by 0.82%0.004 0.006 0.008 0.01 0.012Acceleration of Captured Beam (dP/P)-25-20Beam Center to Collimator (mm)Primary Collimator at -40 mmPrimary Collimator at -35 mmFit (dispersion  = 1.13 m)Momentum Error of Uncaptured BeamVaried Beam Displacement and Primary Collimator PositionFigure 3: To confirm that loss is due to un-accelerated beamwe vary distance from beam center to primary collimatorand observe time and momentum of loss peak. We plotdistance vs. momentum change, finding that it matches ex-pected dispersion.Commissioning has proceeded by creating an orbit dis-tortion at a time before the uncaptured beam reaches a mo-mentum aperture outside the collimation region. One thendefines the momentum aperture with a combination of theprimary collimator position and a position bump at that lo-cation. This defines a point for scattering the particles,setting their orbit downstream. Figure 2 shows the lossrecorded at the primary collimator (and the 2nd secondarycollimator) as well as the beam intensity and the momen-tum to which the capture beam has been accelerated. Us-ing this technique, Fig. 3 shows that the dispersion for lostbeam is similar to that measured in other ways.The secondary collimator positions are optimized bystudying loss patterns recorded by the loss monitor system.Collimators are moved toward the beam edge where thescattered beam is expected. Moving too close will resultin decreasing the accelerated beam. Collimation orbits andthe four collimator positions, both horizontal and vertical,are adjusted to achieve high collimation efficiency for theuncaptured beam. Despite using significant collimation or-bit bumps as acceleration starts, the collimators can still bemoved close enough to provide a significant limiting aper-ture for the injected beam. This results in capturing a largefraction of the pre-acceleration losses in the collimation re-gion also.Figure 4: Logarithmic display of losses around the MainInjector. Integrated loss at the end of the cycle are dis-played in green. Losses after the uncaptured beam lossoverlay this in yellow. Losses at the end of injection over-lay this in blue. Various sums and intensities are displayedat the top and bottom. For this display, the collimation re-gion includes 229 - 309.RESULTSUsing a three decade logarithmic display of all loss mon-itors, we observed the loss patterns during each cycle ofMain Injector operation. For normal operation we displaythis continuously in the Main Control Room. Figure 4 il-lustrates typical operation since an orbit and collimationadjustment in April 2009.0.78 0.79 0.8 0.8100.010.020.030.040.05Loss Fraction (small)(small) ECool Region (LM305A,B,LM306A,B)(small) Beyond Straight Section (LM310 - LM315)0.78 0.79 0.8 0.8100.10.20.3Loss per 4 ms (Rads)Loss Monitor SumLoss Extended Coll Region (LM229 - LM315)Loss Coll Region (LM229 - 309)Uncaptured Beam Loss and Loss Fractionmeasurement at 4 ms intervalsTime in Cycle (sec)0.950.960.970.980.991Loss Fraction (large)(large) Extended Coll Region(large) Coll RegionFigure 5: Loss at collimators compared to loss sum aroundthe ring. The STRUCT simulation reported losses fromLM229 - LM309. The orbit distortion added loss atLM228. We observe small loss from LM310 - LM315which we continue to study.The efficiency calculated for the display in Fig. 4 inte-grates losses over a 74 ms interval. The uncaptured beamis lost in about 12 ms. In Fig 5, the loss measurement hard-ware was configured so all loss monitors record the integralloss in 4 ms intervals. We have taken differences to get theloss in that interval, taken sums of all loss monitors andvarious groups to see the efficiency of collimation. We seethat other loss mechanisms continue as acceleration begins.If we observed losses at the peak of uncaptured beam loss,we find that the collimation captures >99% of the lossesin the region of the collimators. If we include only the re-gion which was included in the simulation, the efficiency ismore than 98%. These results are simple sums of the mea-sured signal in the ionization loss monitors. Variations inthe sampling density and geometry limit our precision forprecisely evaluating the efficiency.A program to monitor residual radiation at selected lo-cations in the Main Injector has monitored activation since2005. To demonstrate the impact of collimation we aver-aged the ratio after (2/2009, 4/2009) to before (12/2007,1/2008) we began using collimation for groups of locationsin major arcs, the collimation region and transfer points atLAM40, LAM52, LAM60/61 and LAM62. Table 1 showsthese results. Since some long-lived isotopes have beenproduced, further improvements are expected at some lo-cations.Table 1: Residual Radiation Ratio: 2009 vs 2008113-221 Coll 40 405-521 52 60 620.26 5.06 0.55 0.30 0.68 0.65 0.70ACKNOWLEDGMENTSWe would like to thank the Fermilab Accelerator Divi-sion Mechanical Support Group, Controls Group and Oper-ations Group for assistance in constructing, commissioningand operating this system.REFERENCES[1] Ioanis Kourbanis. Fermilab Main Injector High Power Op-eration and Future Plans. In Charlie Horak, editor, Proceed-ings of the 42nd ICFA Advanced Beam Dynamics Workshopon High-Intensity, High-Brightness Hadron Beams - 2008,Nashville, TN, USA, 2008.[2] K. Seiya et al. Multi-batch slip stacking in the Main Injectorat Fermilab. In C. Petit-Jean-Genaz, editor, Proceedings ofthe 2007 PARTICLE ACCELERATOR CONFERENCE, pages742–744. IEEE, Piscataway, N.J. 08855-1331, 2007. Alsoavailable as FERMILAB-CONF-07-275-AD.[3] Alexandr I. Drozhdin et al. Collimation System Design forBeam Loss Localization with Slipstacking Injection in theFermilab Main Injector. In C. Petit-Jean-Genaz, editor, Pro-ceedings of the 2007 PARTICLE ACCELERATOR CONFER-ENCE, page 1688. IEEE, Piscataway, N.J. 08855-1331, 2007.Also available as FERMILAB-CONF-07-249-AD.[4] Bruce C. Brown. Main Injector Collimation System Hard-ware. Beams-doc 2881 v2, Fermilab, April 2008.[5] Bruce C. Brown. Collimation System for Beam Loss Lo-calization with Slip Stacking Injection in the Fermilab MainInjector. In Charlie Horak, editor, Proceedings of the42nd ICFA Advanced Beam Dynamics Workshop on High-Intensity, High-Brightness Hadron Beams - 2008, Nashville,TN, USA, 2008.

Fermilab Main Injector Collimation Systems: Design, Commissioning and Operation

https://digital.library.unt.edu/ark:/67531/metadc927219/m2/1/high_res_d/952256.pdf

Fermilab Main Injector Collimation Systems: Design, Commissioning and Operation

Abstract

Similar works

Full text

Available Versions

UNT Digital Library