Some Missouri farmers are harvesting and storing high-moisture corn or milo for cattle rations. This practice has a number of agronomic advantages that are appealing to farmer-feeders who produce their own grain. Also, high-moisture processing improves the feed value of the grain, especially milo.Reviewed October 1993 -- Extension website

Sewell, Homer B.

University of Missouri: MOspace

G2056 High-Moisture Grain for Beef Cattle | University of Missouri Extensionhttp://extension.missouri.edu/publications/DisplayPrinterFriendlyPub.aspx?P=G2056[5/23/2013 2:06:39 PM]University of Missouri ExtensionG2056, Reviewed October 1993High-Moisture Grain for Beef CattleHomer B. SewellDepartment of Animal SciencesSome Missouri farmers are harvesting and storing high-moisture corn or milo for cattle rations. Thispractice has a number of agronomic advantages that are appealing to farmer-feeders who produce theirown grain. Also, high-moisture processing improves the feed value of the grain, especially milo.AdvantagesEarly harvest releases land for fall plowing or stalk field use.Field losses at harvest may be reduced by 5 to 10 percent. Losses average about 13 percent for 15percent moisture grain vs. 2 percent for 26 percent moisture grain.Storage losses are often 2 percent or less of the dry matter, which may be less than rodent and insectdamage in crib storage.Storage costs are usually cheaper than when high-moisture grain is dried for storage.Less investment in equipment is needed for storage and feeding compared to steam flaking.There may be as much as 10 percent improvement in the feed value of the grain for cattle.DisadvantagesA large inventory of grain is needed, which increases capital requirements.Less flexibility of use, since it must be fed to livestock.May freeze in bunk in winter. Flies can be a problem in summer.Optimum harvest conditions may exist only a short time.Improved feed valueMiloHigh-moisture storage improves the feed value of milo more than it does corn as feed for cattle. Hard seedcoat and complex structure of the starch molecule in milo may be largely responsible for its greaterresponse than corn to this and most other processing methods. High-moisture harvested milo has increaseddaily gains slightly (0 to 2 percent) and improved feed efficiency from 6 to 10 percent over dry milo for beefcattle.CornResearch results have varied in measures of the feeding value of high-moisture corn for beef cattle.Improvement has been greater and more consistent with high-moisture ground ear corn than with shelledcorn. The value of the cob appears to be improved.A summary of 14 experiments showed high-moisture ground ear corn increased gains by 3 percent andfeed efficiency by 10 percent over dry ground ear corn. High-moisture ear corn makes a palatable, completefinishing ration for beef cattle. It has 20 percent cob. Cattle are easy to start, keep on feed and gain rapidlyon high-moisture ear corn. Most modern harvesting machinery, however, is not equipped to pick the cob.Earlier summaries showed no improvement in feed value for high-moisture shelled corn. Results have beenG2056 High-Moisture Grain for Beef Cattle | University of Missouri Extensionhttp://extension.missouri.edu/publications/DisplayPrinterFriendlyPub.aspx?P=G2056[5/23/2013 2:06:39 PM]variable, but some recent studies have shown as much as 3 to 5 percent improvement in the value of thedry matter in high-moisture shelled corn for cattle.Rate of gain has been similar for cattle fed dry or high-moisture shelled corn.WheatHigh-moisture storage has not improved the feed value of wheat for cattle in a limited number of trials.High-moisture grain for hogsHigh-moisture grains have the same or slightly greater value than dry grain for hogs on a dry matter basis.There is a problem of keeping it fresh in hot weather, and supplements may need to be fed separately fromthe grain. Unless cattle are being fed, the hog operation often does not use enough grain daily to keephigh-moisture grain fresh in a conventional silo.Moisture levelsHarvest corn and milo when it has 22 to 30 percent moisture. At this moisture range these grains havetheir highest yield of dry matter per acre and preservation conditions are best. Studies with milo haveshown that 30 percent moisture gives greater improvement in feed value than lower moisture levels.Mold is a greater problem with drier grain, and there may be little fermentation. It is difficult to pack drygrain tightly enough to exclude air for proper preservation in trench silos. Grain with as low as 20 percentmoisture can be safely stored in sealed silos, but spoilage may be greater than higher moisture grain inunsealed silos during hot weather. If the grain is harvested too wet and immature, dry matter yield per acrewill be less and a number of kernels will be left on the cob of corn.Grinding at siloGrain should be ground or rolled before it is stored in horizontal or conventional upright silos in order for itto pack tightly and exclude air. Corn kernels should be broken into three or four pieces for proper packing.Use trial and error to determine the best screen size. A 1/2- to 5/8-inch screen is about right for corn. A5/16-inch screen is often used for high-moisture milo. Drier material requires a smaller screen.Grain is stored whole in gas-tight silos. It should be rolled or ground when removed for feeding. Researchhas shown some increase in feed value when high-moisture shelled corn is processed for beef cattle inrations that have over 15 percent roughage. Milo should never be fed whole to cattle.The grain should be packed with a tractor in bunker or trench silos in a fashion similar to silage. The topshould be covered with plastic and weighted down to seal it and prevent air flow beneath the cover in caseof puncture. The plastic cover should be applied within one or two days after filling to prevent deteriorationto the exposed grain. This may necessitate covering the silo as it is being filled. Rapid filling is important forbest preservation in non-sealed silos.Conventional upright silos must be strong and in good condition for storage of high-moisture grain. A silothat has been used for grass silage should be strong enough for high-moisture grain. Consult themanufacturer of your silo if you are in doubt about whether it needs extra bands for reinforcement.Doors may need to be sealed with plastic strips. Seal the top of the silo with a plastic cap to preventspoilage. Cut the plastic 1 to 2 feet larger than the circumference of the silo. Crown the center of the siloand make a ditch around the edge of the silo. This ditch can be filled with any material that will not blowaway, to seal the plastic to the grain.Storage for 21 daysG2056 High-Moisture Grain for Beef Cattle | University of Missouri Extensionhttp://extension.missouri.edu/publications/DisplayPrinterFriendlyPub.aspx?P=G2056[5/23/2013 2:06:39 PM]High-moisture grain should be left in the silo for 21 days to complete the fermentation period before it isfed. Feed 2 to 3 inches of the surface daily to prevent spoilage.ReconstitutionThis is a process whereby water is added to mature grain to raise the moisture content to 25 to 30 percentfor storage in a silo. Studies at Texas and Oklahoma showed reconstituted milo stored whole in airtightstorage for processing at feeding improved rate of gain slightly and feed efficiency by 12 to 15 percent.Both stations found, however, if the milo was ground before reconstituting, there was little improvement infeed value over dry milo for cattle. An average of five trials with reconstituted shelled corn at cornbeltstations showed no improvement in rate of gain and 4.5 percent improvement in feed efficiency by cattle.The corn was stored whole in airtight silos.The gallons of water to add to raise the moisture level of grain is given in Table 1. Water can be addedwhile it is on the wagon, or at the grinder, blower, or auger as it goes into the silo. Warming water to 100degrees Fahrenheit increases its absorption by whole grain. Adding water to ground grain is mostsatisfactory.Table 1Amount of water to be added in ensiling high-moisture grainMoisture in grain Percent moisture desired30 29 28 27 26 25 24Gallons of water to be added per ton29 percent 3.5       28 percent 7.0 3.5      27 percent 10.5 7.0 3.5     26 percent 14.0 10.5 7.0 3.5    25 percent 17.5 14.0 10.5 7.0 3.5   24 percent 21.0 17.5 14.0 10.0 7.0 3.5  23 percent 24.5 21.0 17.5 13.5 10.0 7.0 3.522 percent 28.0 24.5 21.0 17.0 13.0 10.0 7.021 percent 31.5 28.0 24.0 20.5 17.0 13.0 10.020 percent 35.0 31.5 27.5 24.0 20.0 17.0 13.019 percent 38.5 35.0 31.0 27.5 23.5 20.0 17.018 percent 42.0 38.5 34.5 31.0 27.0 23.5 20.017 percent 46.0 42.0 38.0 34.0 30.5 26.5 23.516 percent 50.0 46.0 42.0 37.5 34.0 30.0 26.0A good rule of thumb: to increase the moisture content of grain to 25 percent, add 3-1/3 gallons of water(26.7 pounds) to 1 ton of grain for each 1 percent moisture deficiency. If grain has 15 percent moisture (10percent deficiency), adding 33 gallons (267 pounds) of water to a ton of grain raises the moisture to 25percent. Add approximately 3.6 gallons for each 1 percent moisture deficiency to raise it to 30 percentmoisture.G2056 High-Moisture Grain for Beef Cattle | University of Missouri Extensionhttp://extension.missouri.edu/publications/DisplayPrinterFriendlyPub.aspx?P=G2056[5/23/2013 2:06:39 PM]Remember these simple figures, and when a table isn't handy, you can still figure out how much water toadd to a ton of grain to raise the moisture content to these levels.Type of siloSealed storage is the most expensive structure. It has the least storage losses. Filling and feeding can beinterrupted without feed spoilage. Storing the grain whole appears to have some advantage for thereconstitution of milo.Conventional upright silos rank next to sealed silos in storage losses but have had 4 to 6 percent more drymatter loss in some studies. They cost much less than sealed units for the same storage capacity.Management is more critical for conventional silos but not as great as for bunkers and trenches. The topcan be resealed if feeding stops before emptied.Horizontal units have the least cost, but management is important for their success. A good job of filling,packing and covering is needed to keep storage losses low. Storage losses can be held to a minimum inlarge capacity trench or bunker silos that are well managed. Losses need not be much higher under theseconditions than those in upright silos. Using a stationary loader or a front end scoop on a tractor to removegrain from a horizontal silo makes a fast, efficient way to feed. These silos are used most exclusively incommercial feedlots of the high plains to store the large quantity of high-moisture grain needed by this sizelot.Size of siloTable 2 gives the number of cattle required to consume 2 inches of high-moisture corn daily from thesurface of a 60-foot-tall tower silo at various levels of grain feeding. This is an average figure for the silo. Agreater depth would be removed daily from the top than the bottom of the silo when the same poundage isfed. The numbers in Table 2 also give the number of cattle that can be fed for 360 days from a 60-foot-high silo when fed at this rate. This will aid in figuring the number of silos needed.Table 2Number of cattle required to consume 2 inches per day from various sizes of tower silos Silo diameter16 feet 20 feet 24 feet 30 feetPounds fed per head daily1 Number of cattle required5 267 419 604 94410 133 209 302 47215 89 140 201 31520 67 105 151 23625 53 84 121 189128 percent moisture basis, and 40 lpounds per cubic foot.In a horizontal silo, grain should be piled at least 12 feet high to minimize surface exposed, but not morethan 18 feet high so that packing won't be difficult and removal won't be dangerous.At least 4 inches per day should be removed from the surface of the grain to prevent spoilage in ahorizontal silo. Table 3 gives estimates of the number of cattle needed to remove 4 inches a day from a 14-G2056 High-Moisture Grain for Beef Cattle | University of Missouri Extensionhttp://extension.missouri.edu/publications/DisplayPrinterFriendlyPub.aspx?P=G2056[5/23/2013 2:06:39 PM]foot depth at various silo widths and rates of feeding.Table 3Number of cattle required to consume 4 inches per day from various widths of horizontal silos Silo width30 feet 40 feet 50 feet 60 feet 70 feet 80 feetPounds fed per head daily1 Number of cattle required5 1,400 1,867 2,333 2,800 3,267 3,73310 700 933 1,167 1,400 1,633 1,86715 467 622 778 933 1,089 1,24420 350 467 583 700 817 93325 280 373 467 560 653 747128 percent moisture basis, 50 pounds per cubic foot.These cattle numbers also show many cattle can be fed to 360 days from a silo 120 feet long. Thesenumbers are helpful in estimating the number and lengths of horizontal silos needed to store high-moisturegrain for the number of cattle you feed.Adding urea and mineralsSome cattle feeders correct the protein and mineral deficiencies of ground high-moisture shelled corn byadding at time of ensiling the mixture in Table 2. Adding 0.4 pounds of this mixture per ton of high-moisture corn for each percent of dry matter corrects the nutrient content on an air-dry (90 percent drymatter) basis to approximately 11 percent crude protein, 0.27 percent calcium, 0.23 percent phosphorus,and 0.50 percent salt. Corn with 80 percent dry matter (20 percent moisture) or 70 percent dry matter (30percent moisture) would require 32 pounds and 28 pounds of the mixture per ton, respectively. If urea isused alone, add per ton at the rate of 0.16 pound for each percent of dry matter in the corn. The additiveshould be mixed uniformly with the corn.Table 4The composition of additive mixtureAdditive PercentUrea (45 percent nitrogen) 40Limestone, feed grade 33Salt, trace-mineralized 27Total 100Remember when feeding high-moisture corn that it takes more pounds to supply the same amount of drymatter. Compared to corn with 15 percent moisture, it takes 6, 13 and 21 percent more of 20, 25 and 30percent moisture corn for equal dry matter weights.G2056, reviewed October 1993G2056 High-Moisture Grain for Beef Cattle | University of Missouri Extensionhttp://extension.missouri.edu/publications/DisplayPrinterFriendlyPub.aspx?P=G2056[5/23/2013 2:06:39 PM]Related MU Extension publicationsG2051, Feed Ingredient Composition for Beef Cattlehttp://extension.missouri.edu/p/G2051G2058, Vitamins for Beef Cattlehttp://extension.missouri.edu/p/G2058G2064, Winter Rations for Beef Calveshttp://extension.missouri.edu/p/G2064G2071, Urea Supplements for Beef Cattlehttp://extension.missouri.edu/p/G2071G4020, Tables for Weights and Measurements: Cropshttp://extension.missouri.edu/p/G4020Order publications online at http://extension.missouri.edu/explore/shop/ or call toll-free 800-292-0969.

High-moisture grain for beef cattle (1993)

Abstract

Similar works

Full text

Available Versions

University of Missouri: MOspace