In this paper a two stage bidirectional resonantdc-dc converter is introduced for battery hybrid power generators. The bidirectional dc-dc converter consists of two stage, one is series resonant converter and another is non isolated half bridge dc-dc converter. The zero current switching is applied to series resonant converter so that magnetic components and EMI filters can be optimized. The PI controller is used for non-isolated converter. The high side voltage and low side voltage are regulated efficiently due PI controller. The application two stage bidirectional dc-dc converter is in uninterrupted power system to provide additional power to critical ac loads. The MATLAB simulation of step-up and step-down mode of bidirectional dc-dc converter is provided validate performance of proposed two stage bidirectional dc-dc converter

R. A. Metri

Sonali M. Deshmukh

English

International Journal of Innovations in Engineering Research and Technology

Proceedings of  INTERNATIONAL CONFERENCE ON COMPUTING, COMMUNICATION AND ENERGY SYSTEMS  (ICCCES-16) In Association with IET, UK & Sponsored by TEQIP-II 29th -30th, Jan. 2016 Paper ID: EE30 K.E. Society's  RAJARAMBAPU INSTITUTE OF TECHNOLOGY TWO STAGE BIDIRECTIONAL DC-DC CONVERTER FOR BATTERY HYBRID POWER GENERATORS  Sonali M. Deshmukh M.Tech student, Department of Electrical Engineering Rajarambapu Institute of technology  Maharashtra, India. R. A. Metri Asst. Professor, Department of electrical Engineering Rajarambapu Institute of technology Maharashtra, India   Abstract— In this paper a two stage bidirectional resonant dc-dc converter is introduced for battery hybrid power generators. The bidirectional dc-dc converter consists of two stage, one is series resonant converter and another is non isolated half bridge dc-dc converter. The zero current switching is applied to series resonant converter so that magnetic components and EMI filters can be optimized. The PI controller is used for non-isolated converter. The high side voltage and low side voltage are regulated efficiently due PI controller. The application two stage bidirectional dc-dc converter is in uninterrupted power system to provide additional power to critical ac loads. The MATLAB simulation of step-up and step-down mode of bidirectional dc-dc converter is provided validate performance of proposed two stage bidirectional dc-dc converter.  Keywords—Biditrctional  dc-dc converter (BDC) ,Hybrid power genertors, series resonant converter (SRC), Zero current switching (ZCS), PI. NOMENCLATURE  Lr            : Resonant Inductance  Cr       : Resonant Capacitance f r            : Resonant Frequency Dd Ts      : On-Time duty cycle of SRC f s1        :Switching frequency of the SRC. f s2        :Switching frequency of non-isolated converter V H                : High Side Voltage of BDC V L           : Low side Voltage of BD ILm                 :Magnetizing current of SRC IL            : Low side current of SRC ILr           :Resonant current of the SRC ISL          : Low side current of SRC VSH        : High Side voltage of SRC VSL         : Low side voltage of SRC LKP         : Primary side leakage inductor current  of SRC  LKS        : Secondary side Leakage Inductor Current of SRC  I.       INTRODUCTION  In recent years, the rate of power consumption in industrial loads, residential load and different activities in IT companies, banks, hospitals etc. has increased. The continuous power supply is required in these facilities, so use of uninterruptible power supply system, standby or emergency generator is increased. In utility power failure these standby or generators are used for backup power supply [1]. In the event of loss of utility power these standby or diesel generator system fails to supply loads when power generated by generator is less than power required by loads. The generator systems are unable counter sudden changes in loads so he power balancing between generator and load is required and for this purpose energy stored battery systems are required[3][4]. The bidirectional dc-dc transfer required to exchange power between battery system and rest of system.  As shown in fig. 1 the BDC is placed between high voltage dc bus and low voltage bus. When generator power is less than load then bidirectional dc-dc converter transfer power to balance the ac load through battery discharging. When the generator balances the load the BDC charges the battery.  Fig.1 Battery Hybrid Power Generator System  The BDC should provide a galvanic isolation and a high step up/down voltage conversion ratio in the application where the low-voltage battery is used. Typical topology candidates with these requirements include half-bridge, full-bridge, and push-pull pulse width modulation (PWM) converters [10], [11] , Proceedings of  INTERNATIONAL CONFERENCE ON COMPUTING, COMMUNICATION AND ENERGY SYSTEMS  (ICCCES-16) In Association with IET, UK & Sponsored by TEQIP-II 29th -30th, Jan. 2016 Paper ID: EE30 K.E. Society's  RAJARAMBAPU INSTITUTE OF TECHNOLOGY dual active bridge (DAB) converters [12], [13], and two-stage converters [14], [15]. The PWM converters usually necessitate passive or active clamping on the low-voltage side to clamp the surge voltage generated by the leakage inductance of the transformer. The active clamping technique makes the converter not only clamp the surge voltage, but achieve zero-voltage switching (ZVS) turn-on of all the switches. A drawback of the active clamped PWM converter is high turn-off switching losses [16]. The DAB has a modular and symmetric structure and can achieve ZVS turn-on without auxiliary components. However, the DAB has limited ZVS range and high-circulating currents for applications requiring wide voltage variation. The ripple current of the DAB converters is high and especially problematic in the low-voltage applications [17]. Two-stage converters consist of a non-isolated stage and an isolated stage. Since the non-isolated stage is operated to regulate the voltage and power flow, the isolated stage can be designed with minimum components’ rating. Even though the power is passing through two conversion stages, the two-stage converter could achieve a higher efficiency especially in a wide voltage range application [14], [15].  In this paper a two stage bidirectional dc-dc converter is introduced with ZCS and PI controller. The BDC consists of half bridge dc-dc converter and series resonant converter. The ZCS reduces switching losses in converter. The zero current switching is used to control series resonant converter. The PI control is used to control non-isolated converter. The section II describes the proposed two stage BDC. The next section III describes modes of operation of SRC. The section IV describes control strategy of BDC. In section V simulation results are presented II. PROPOSED TWO STAGE BDC  The two stage bidirectional dc-dc converter consist of non-isolated converter and series loaded resonant converter. In this the high side voltage is connected at non-isolated converter. This non-isolated converter is used for controlling either high-side voltage or low side voltage. The series resonant converter is operated at fixed frequency. In first stage, non-isolated converter converts DC-DC voltage. The obtained DC voltage is then converted to AC voltage by half bridge converter circuit. This ac voltage is step-downed using transformer with turn’s ratio 5:1. The converted AC voltage is then converted into DC voltage using full bridge rectifier circuit. The zero current soft switching technique is used for series resonant converter regardless of change in voltage or load. The PI controller is used to control non-isolated converter to regulate either high side voltage or low side voltage.   Fig.2 Two stage bidirectional dc-dc converter III. MODES OF OPERATION  OF SRC The operation of SRC is based on fixed frequency and fixed duty with minimum current and voltage rating. The ZCS is applied to SRC to improve EMI filter. Modes of operation and key-waveforms of series loaded resonant converter are shown in fig.3, 4 and fig.5. The expression of angular resonant frequency of SRC can determined by,                                 The expression of resonant inductance can be determined by,                                 The expression of resonant capacitance can be determined by,                                     A. Mode I (to-t1) In this mode switch  and switch  are on. The on time duty cycle is selected in such way so the low side current becomes purely sinusoidal. The on time duty cycle should be selected as . The low side current can be expressed as                                   The voltage across  can be determined by                             Therefore from (4) and (5) can be determined by           Proceedings of  INTERNATIONAL CONFERENCE ON COMPUTING, COMMUNICATION AND ENERGY SYSTEMS  (ICCCES-16) In Association with IET, UK & Sponsored by TEQIP-II 29th -30th, Jan. 2016 Paper ID: EE30 K.E. Society's  RAJARAMBAPU INSTITUTE OF TECHNOLOGY  Fig. 3 Mode I of SRC  The resonant current can then be obtained using (4) and (6) by    Neglecting voltage oscillation after turning ON of SL2, the voltage across low side switch SL1 at Mode I (t0 −t1) is expressed as,  The turn-off voltage of low side switch can be obtained by,    It should be noted that VSL,off should be greater than zero for the proposed operation. Therefore, from (4) and (9) the secondary side leakage inductance should be limited such as,   B. Mode II (t1-t2)  In Mode II, Switch SH1 is turned OFF at t1, and turn-off current of the high side switch, ISH,off , becomes equal to the peak magnetizing current ILm,pk. Since Lm is made very large in the proposed SRC, I Lm,pk is very small, resulting in negligible switch turn-off losses. The output capacitors of SH1 and SH2 are charged and discharged, respectively by ILm,pk, as shown in Fig. 3. The charging and discharging operation may not be completed at the end of Mode II if ILm,pk is not sufficiently large, which may lead to a nonzero turn-on voltage of high and low side switches. The turn-on voltages of the high and low side switches can be determined respectively by        Fig.4 Mode II of SRC Note that SH2 and SL1 are turned ON with ZCS, but there exists turn-on losses of high- and low side switches associated with energy stored in MOSFET’s output capacitances as follows [18],  [19].  IV Control Strategy The PI controller is used for controlling non-isolated converter for regulating high voltage side and low voltage side. The reference voltage for controlling high voltage side is taken as 400V.The reference voltage for controlling low voltage side is taken as 28V.  Fig. 5 Control strategy for low side voltage   Fig. 6 Control strategy for high side voltage Proceedings of  INTERNATIONAL CONFERENCE ON COMPUTING, COMMUNICATION AND ENERGY SYSTEMS  (ICCCES-16) In Association with IET, UK & Sponsored by TEQIP-II 29th -30th, Jan. 2016 Paper ID: EE30 K.E. Society's  RAJARAMBAPU INSTITUTE OF TECHNOLOGY                     V  Simulation Result Simulation parameter of proposed bidirectional dc-dc converter are shown in Table I.  TABLE I  PARAMETERS OF THE PROPOSED BDC Parameter Value Parameter Value Po 5 KW Lf 0.42µH VH 340-440 V Lr 5.8µH VL 24-32 V Cf 110µH fs1 48 KHz CH 45µH fs2 20 KHz Ci 100µF Np:Ns 5:1 CL 380µF DdTs 600 ns Cr1 0.94µF LB 1 mH Cr2 0.94µF  Simulation waveforms of high and low voltage side control are shown as follows, The Fig.7 shows gate pulses of switch SH1, SH2, SL1, SL2.Fig.8 and fig.9 shows waveform of current ILr, ILm. and ISH, ISH2 respectively. The fig.10 shows the waveform of voltage Vcr1 andVcr2. Fig.11 shows output waveform of low side voltage control. Fig.12 shows output voltage of high side voltage.  0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.500.51TimeSH1,SL20.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.500.51TimeSH2,SL1 Fig.7 Gate pulse for SH1, SH2, SL1 and SL2 4.5 4.55 4.6 4.65 4.7 4.75 4.8 4.85 4.9 4.95 5x 10-4-1.5-1-0.500.511.5TimeILr & ILm Fig.8  ILr and ILm 0.0956 0.0956 0.0956 0.0956 0.0956 0.0957 0.0957 0.0957 0.0957 0.0957-0.500.51IsL10.0956 0.0956 0.0956 0.0956 0.0956 0.0957 0.0957 0.0957 0.0957 0.0957-0.500.51TimeIsL2 Fig.9 ISH1 and ISH2 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5190.8191191.2TimevoltageVcr1 & Vcr2 Fig. 10 Vcr1 and Vcr2 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5051015202530TimeVoltage Fig.11 Output waveform of low side voltage control 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5050100150200250300350400450TimeVoltage Fig.12 Output waveform of high side voltage control VI CONCLUSION This paper presents a two stage bidirectional dc-dc converter. The advantages of two stage converter are simple switching technology, reduced component rating of isolated converter. The series resonant converter operates at zero current switching technique so reduces switching losses and improves performance of converter. This bidirectional converter used for stepping up and down voltage.  REFERENCES  [1] P. Famouri, W. R. Cawthorne, N. Clark, S. Nandkumar, C. Atkinson, R. Atkinson, T. McDaniel, and S. Petreanu, “Design and testing of a novel linear alternator and engine system for remote electrical power generation,” in Proc. IEEE Power Eng. Soc. Winter Meeting, Jan. 31–Feb. 4, 1999, pp. 108–112. [2] Z.ChenandY.Hu,“Ahybridgenerationsystemusingvariablespeedwind turbines and diesel units,” in Proc. IEEE 29th Annu. Conf. Ind. Electron. Soc., Nov. 2–6, 2003, pp. 2729–2734 [3] E. Muljadi and T. J. Bialasiewicz, “Hybrid power system with a controlled energy storage,” in Proc. IEEE 29th Annu. Conf. Ind. Electron. Soc., Nov. 2–6, 2003, pp. 1296–1301. [4] L. Wang and D. Lee, “Load-tracking performance of an autonomous SOFC-based hybrid power generation energy Proceedings of  INTERNATIONAL CONFERENCE ON COMPUTING, COMMUNICATION AND ENERGY SYSTEMS  (ICCCES-16) In Association with IET, UK & Sponsored by TEQIP-II 29th -30th, Jan. 2016 Paper ID: EE30 K.E. Society's  RAJARAMBAPU INSTITUTE OF TECHNOLOGY storage system,” IEEE Trans. Energy Convers., vol. 25, no. 1, pp. 128–139, Mar. 2010. [5] D. Kim and S. Choi, “Load balancing with mobile base stations in tactical information communication networks,” in Proc. IEEE Wireless Commun. Netw. Conf., Mar. 28–31, 2011, pp. 28–31. [6] H. Wen, X. Wen, J. Liu, X. Guo, and F. Zhao, “A low-inductance highfrequency film capacitor for electric vehicles,” in Proc. Int. Conf. Electr. Mach. Syst., Oct. 8–11, 2007, pp. 2046–2050. [7] Y. X. Qin, H. S. H. Chung, D. Y. Lin, and S. Y. R. Hui, “Current source ballast for high power lighting emitting diodes without electrolytic capacitor,” in Proc. IEEE 34th Annu. Conf. Ind. Electron., Nov. 10–13,  [8] 2008 , pp. 1968–1973. [9] J. Kim and S. Sul, “Resonant link bidirectional power converter. Part II—Application to bidirectional AC motor drive without electrolytic capacitor,” IEEE Trans. Ind. Appl., vol. 10, no. 4, pp. 485–493, Jul. 1995. [10] H. Chae, H. Moon, and J. Lee, “On-board battery charger for PHEV without high-voltage electrolytic capacitor,” Electron. Lett., vol. 46, pp. 1691– 1692, Dec. 2010. [11] L. Rongyuan, A. Pottharst, N. Frohleke, and J. Bocker, “Analysis and design of improved isolated full-bridge bidirectional DC–DC converter,” in Proc. IEEE 35th Annu. Power Electron. Spec. Conf., Jun. 20–25, 2004, pp. 521–526. [12] G. Ma, W. Qu, G. Yu, Y. Liu, N. Liang, and W. Li, “A zero-voltageswitching bidirectional DC–DC converter with state analysis and softswitching-oriented design consideration,” IEEE Trans. Ind. Electron., vol. 56, no. 6, pp. 2174–2184, Jun. 2009. [13] R. W. De Doncker, D. M. Divan, and M. H. Kheraluwala, “A three-phase soft-switched high-power density DC/DC converter for high-power applications,” IEEE Trans. Ind. Appl., vol. 27, no. 1, pp. 63–73, Jan. /Feb. 1991. [14] F. Krismer and J. W. Kolar, “Efficiency-optimized high-current dual active bridge converter for automotive applications,” IEEE Trans. Ind. Electron., vol. 59, no. 7, pp. 2745–2760, Jul. 2012. [15] D. S. Gautam and A. K. S. Bhat, “A comparison of soft-switched DC-toDC converters for electrolyzer application,” IEEE Trans. Power Electron., vol. 28, no. 1, pp. 54–63, Jan. 2013. [16] D. Gautam, F. Musavi, M. Edington, W. Eberle, and W. G. Dunford, “An automotive on-board 3.3 kW battery charger for PHEV application,” in Proc. IEEE Vehicle Power Propuls. Conf., Sep. 6–9, 2011, pp. 1 – 6. [17] D. Fu, F. C. Lee, Y. Liu, and M. Xu, “Novel multi-element resonant converters for front-end dc/dc converters,” in Proc. 39th IEEE Annu. Power Electron. Spec. Conf., Jun. 15–19, 2008, pp. 250–256. [18] H. Xiao and S. Xie, “A ZVS bidirectional DC–DC converter with phaseshift plus PWM control scheme,” IEEE Trans. Power Electron., vol. 23 , no. 2, pp. 813–823, Mar. 2008. [19] K. Liu and F. C. Y. Lee, “Zero-voltage switching technique in DC/DC converters,” IEEE Trans. Power Electron., vol. 5, no. 3, pp. 293–304, Jul. 1990.                         

TWO STAGE BIDIRECTIONAL DC-DC CONVERTER FOR BATTERY HYBRID POWER GENERATORS

https://repo.ijiert.org/index.php/ijiert/article/view/1061/1008

TWO STAGE BIDIRECTIONAL DC-DC CONVERTER FOR BATTERY HYBRID POWER GENERATORS

Abstract

Similar works

Full text

Available Versions

International Journal of Innovations in Engineering Research and Technology