Effect of suction/injection on the rate of entropy generation of third grade fluid with convective cooling is analysed in this work. The highly non-linear boundary value problems obtained from the governing equations are solved by Adomian decomposition method (ADM).

Some plots are presented to explain the influence of pertinent parameters on fluid motion, temperature, entropy generation and irreversibility ratio. From the results it is shown that

suction/injection and third grade fluid parameters reduce fluid velocity across the channel, and

increase in suction/injection parameter enhances fluid temperature while convective cooling

parameter reduces it. Entropy generation is enhanced by suction/injection parameter at the lower

wall but reduces it at the upper wal

Agboola, O.O.

Gbadeyan, J.A.

Okagbue, H. I.

Opanuga, A. A.

Covenant University Repository

Defect and Diffusion Forum        Submitted: 2017-10-09 ISSN: 1662-9507, Vol. 384, pp 21-30       Revised: 2018-02-11 doi:10.4028/www.scientific.net/DDF.384.21      Accepted: 2018-02-12 © 2018 Trans Tech Publications, Switzerland      Online: 2018-05-08   Effect of Suction/Injection on the Entropy Generation of Third Grade Fluid with Convective Cooling Abiodun A. Opanuga1,a*, Jacob A. Gbadeyan2,b, Olasunmbo O. Agboola1,c, Hilary I. Okagbue1,d  1Department of Mathematics, College of Science & Technology, Covenant University, Ota, Nigeria. 2Department of Mathematics, Faculty of Physical Science, University of Ilorin, Ilorin, Nigeria *aabiodun.opanuga@covenantuniversity.edu.ng, bj.agbadeyan@yahoo.com, cola.agboola@covenantuniversity.edu.ng, dhilary.okagbue@covenantuniversity.edu.ng  Keywords: Suction/injection, convective cooling, third grade fluid, entropy generation, Adomian decomposition method.  Abstract: Effect of suction/injection on the rate of entropy generation of third grade fluid with convective cooling is analysed in this work. The highly non-linear boundary value problems obtained from the governing equations are solved by Adomian decomposition method (ADM). Some plots are presented to explain the influence of pertinent parameters on fluid motion, temperature, entropy generation and irreversibility ratio. From the results it is shown that suction/injection and third grade fluid parameters reduce fluid velocity across the channel, and increase in suction/injection parameter enhances fluid temperature while convective cooling parameter reduces it. Entropy generation is enhanced by suction/injection parameter at the lower wall but reduces it at the upper wall.  References [1]. T. Hayat, F. Shahzad, M. Ayub Analytical solution for the steady flow of the third grade fluid in a porous half space, Applied Mathematical Modelling, 31 (2007): 2424–2432 [2]. T. Hayata, A.H. Kara Couette flow of a third-grade fluid with variable magnetic field, Mathematical and Computer Modelling, 43 (2006): 132–137 [3]. T. Hayat, A. Shafiq, M. Nawaz, A. Alsaed, MHD axisymmetric flow of third grade fluid between porous disks with heat transfer, Appl. Math. Mech. (Engl. Ed)., 33(6): 749–764 (2012). DOI 10.1007/s10483-012-1584-9 [4]. T. Hayat, R. Ellahi, F. M. Mahomed, The Analytical Solutions for Magnetohydrodynamic Flow of a Third Order Fluid in a Porous Medium, Z. Naturforsch, 64a (2009):531 – 539 [5]. S.O. Adesanya, Second law analysis for third-grade fluid with variable properties, Journal of Thermodynamics, Volume 2014, Article ID 452168, 8 pages. http://dx.doi.org/10.1155/2014/452168 [6]. S.O. Adesanya, O.D. Makinde, Thermodynamic analysis for a third grade fluid through a vertical channel with internal heat generation, Journal of Hydrodynamics, 27(2)(2015): 264-272. DOI: 10.1016/S1001-6058(15)60481-4 [7]. S. O. Adesanya, J.A. Falade, Thermodynamics analysis of hydromagnetic third grade fluid flow through a channel filled with porous medium, Alexandria Engineering Journal, 54, (2015): 615– 622 [8]. S. O. Adesanya, J.A. Falade, S. Jangili, O. A. Beg, Irreversibility analysis for reactive thirdgrade fluid flow and heat transfer with convective wall cooling, Alexandria Engineering Journal (2017) 56, 153–160. [9]. A.M. Siddiqui, A. Zeb, Q.K. Ghori, A.M. Benharbit, Homotopy perturbation method for heat transfer flow of a third grade fluid between parallel plates, Chaos, Solitons and Fractals, 36 (2008) 182–192 [10]. A.M. Siddiqui, M. Hameed, B.M. Siddiqui, Q.K. Ghori, Use of Adomian decomposition method in the study of parallel plate flow of a third grade fluid, Commun Nonlinear Sci Numer Simulat, 15 (2010): 2388–2399  [11]. M. Azimi, A. Azimi, Investigation on the Film Flow of a Third Grade Fluid on an Inclined Plane Using HPM, Mechanics and Mechanical Engineering, 18(1), (2014): 5–10 [12]. I.G. Baoku, B.I. Olajuwon, A.O. Mustapha, Heat and mass transfer on a MHD third grade fluid with partial slip flow past an infinite vertical insulated porous plate in a porous medium, International Journal of Heat and Fluid Flow, 40 (2013): 81–88 [13]. R. Kandasamy, I. Hashim, A. B. Khamis and I. Muhaimin, Combined heat and mass transfer in MHD free convection from a wedge with ohmic heating and viscous dissipation in the presence of suction or injection, Iranian Journal of Science & Technology, Transaction A, 31(A2)(2007): 151-162. [14]. K.A. Yih, Uniform suction/blowing effect on force convection about wedge. Acta Mech., 128 (1998): 173-181 [15]. S. A. Al-Sanea, Mixed convection heat transfer along a continuously moving heated vertical plate with suction or injection, International Journal of Heat and Mass Transfer, vol. 47(6- 7)(2004): 1445–1465, 2004 [16]. B. K. Jha and B. Aina, Role of suction/injection on steady fully developed mixed convection flow in a vertical parallel plate microchannel, Ain Shams Engineering Journal, 2016. https://doi.org/10.1016/j.asej.2016.05.001 [17]. N.G. Kafoussias and N.D. Nanousis, Magnetohydrodynamic laminar boundary layer flow over a wedge with suction or injection. Canadian Journal of Physics, 75(1997): 733-745 [18]. S.P. Anjali Devi and R. Kandasamy, Effects of heat and mass transfer on MHD laminar boundary layer flow over a wedge with suction or injection. Journal of Energy Heat and Mass Transfer, 23(2001): 167-175. [19]. M.E. Ali and K. Al-Salem, The effect of suction or injection on the boundary layer flows induced by continuous surfaces stretched with prescribed skin friction, Meccanica, 48(2013): 1587–1597, DOI 10.1007/s11012-012-9687-2 [20]. I. J. Uwanta andM.M. Hamza, Effect of suction/injection on unsteady hydromagnetic convective flow of reactive viscous fluid between vertical porous plates with thermal diffusion, International Scholarly Research Notices, Volume 2014, http://dx.doi.org/10.1155/2014/980270 [21]. S. K. Jena and M. N. Mathur, Free convection in the laminar boundary layer flow of a thermomicropolar fluid past a vertical flat plate with suction/injection, Acta Mechanica, 42(3-4) (1982): 227–238. [22]. A.A. Opanuga, J.A. Gbadeyan, and S.A. Iyase, Second law analysis of hydromagnetic couple stress fluid embedded in a non-Darcian porous medium, IAENG International Journal of Applied Mathematics, 47(3)(2017):287-294. [23]. A. A. Opanuga, J. A. Gbadeyan, and S. A. Iyase, "Thermodynamics Analysis of Radiative Hydromagnetic Couple Stress Fluid through a Channel," Lecture Notes in Engineering and Computer Science: Proceedings of The World Congress on Engineering 2017, 5-7 July, 2017, London, U.K., pp. 90-101 [24]. A.A. Opanuga, O.O. Agboola, H.I. Okagbue, J.G. Oghonyon, Solution of differential equations by three semi-analytical techniques, International Journal of Applied Engineering Research, 10(18)(2015): 39168-39174. [25]. A.A. Opanuga, E.A. Owoloko and H.I. Okagbue (2017). Comparison Homotopy Perturbation and Adomian Decomposition Techniques for Parabolic Equations. Lecture Notes in Engineering and Computer Science: Proceedings of The World Congress on Engineering 2017, 5-7 July, 2017, London, U.K., pp24-27 [26]. O. O. Agboola, A.A. Opanuga, J.A. Gbadeyan, Solution of third order ordinary differential equations using differential transform method, Global Journal of Pure and Applied Mathematics, 11( 4)(2015): 2511-2517 [27]. A.A. Opanuga, O.O. Agboola and H.I. Okagbue, Approximate solution of multipoint boundary value problems, Journal of Engineering and Applied Sciences, 10(4)(2015): 85- 89. [28]. J. H. He, Variational Iteration Method for Autonomous Ordinary Differential Systems, Applied Mathematics and Computation, 114(2-3) (2000): 115-123. doi:10.1016/S0096-3003(99) 00104-6 [29]. A.M. Wazwaz, (2001). The numerical solution of fifth order boundary value problems by the decomposition method. Journal of Computational and Applied Mathematics, 136(2001): 259-270. [30]. A. A. Opanuga, H. I. Okagbue, and O. O. Agboola, "Application of Semi-Analytical Technique for Solving Thirteenth Order Boundary Value Problem," Lecture Notes inEngineering and Computer Science: Proceedings of The World Congress on Engineering and Computer Science 2017, 25-27 October, 2017, San Francisco, USA, pp145-148 [31]. A.M. Wazwaz, (2001). The numerical solution of sixth-order boundary value problems by modified decomposition method. Appl. Math. Comput, 118(2001): 311-325 [32]. A. Bejan, Second law analysis in heat transfer, Energy int. J., 15(1980): 721-732. [33]. A. Bejan, Second law analysis in heat transfer and thermal design, Adv. Heat Transfer, 15(1982): 1-58. [34]. A.O. Ajibade, B.K. Jha, and A. Omame, Entropy generation under the effect of suction/ injection, Applied Mathematical Modelling, 35(2011): 4630–4646. [35]. S. O. Adesanya, S.O. Kareem, J.A. Falade and S.A. Arekete, Entropy generation analysis for a reactive couple stress fluid flow through a channel saturated with porous material, Energy, 93(2015): 1239-1245. [36]. A.A. Opanuga, H.I. Okagbue, O.O. Agboola and O.F. Imaga, Entropy generation analysis of buoyancy effect on hydromagnetic Poiseuille flow with internal heat generation. Defect and Diffusion Forum, 378(2017): 102-112. [37]. A.A. Opanuga, H.I. Okagbue, O.O. Agboola (2017). Irreversibility Analysis of a Radiative MHD Poiseuille Flow through Porous Medium with Slip Condition. Lecture Notes in Engineering and Computer Science: Proceedings of The World Congress on Engineering 2017, 5-7 July, 2017, London, U.K., pp.167-171 [38]. S. Das and R. N. Jana, Entropy generation due to MHD flow in a porous channel with Navier slip, Ain Shams Engineering Journal, 5(2014): 575-584. [39]. H. Pop and W. Watanabe, The effect of suction or injection in the boundary layer flow and heat transfer on a continuous moving surface, Technische Mechanik, 13(1992): 49-54. [40]. I. J. Uwanta and M.M. Hamza, Effect of Suction/Injection on Unsteady Hydromagnetic Convective Flow of Reactive Viscous Fluid between Vertical Porous Plates with Thermal Diffusion, Hindawi Publishing Corporation, International Scholarly Research Notices, Volume 2014, Article ID 980270, 14 pages http://dx.doi.org/10.1155/2014/980270 [41]. A. S. Eegunjobi and O. D. Makinde, Effects of Navier Slip on Entropy Generation in a Porous Channel with Suction/Injection, Journal of Thermal Science and Technology, 7(4)(2012): 522-535 [42]. A. O. Ajibade, B.K. Jha, A. Omame, Entropy generation under the effect of suction/injection, Applied Mathematical Modelling, 35 (2011): 4630–4646 [43]. S. O. Adesanya and O. D. Makinde (2015c), Effects of couple stresses on entropy generation rate in a porous channel with convective heating, Comp. Appl. Math. 34, 293–307 

Effect of Suction/Injection on the Entropy Generation of Third Grade

Fluid with Convective Cooling

http://eprints.covenantuniversity.edu.ng/11822/1/Effect%20of%20SuctionInjection%20on%20the%20Entropy%20Generation%20of%20Third.pdf

Effect of Suction/Injection on the Entropy Generation of Third Grade Fluid with Convective Cooling

Abstract

Similar works

Full text

Available Versions

Covenant University Repository