There have been reported cases of the crusher jaw failure due to the high level of impact, tear and shear stresses experienced by the crusher jaw during service. The purpose of this paper is to select a suitable candidate material for the design of crusher jaw that can sustain fracture by any of the three modes of failure – tear, shear and impact at low cost using CES EduPack

Abioye, Abiodun A.

Adetunji, Adelana Razak

Akinluwade, K. J.

Isadare, Dayo Adeyemi

Covenant University Repository

International Journal of Materials Engineering 2015, 5(2): 17-22 DOI: 10.5923/j.ijme.20150502.01 Material Selection for Crusher Jaw in a Jaw Crusher Equipment Adelana Rasaki Adetunji1,2, Abiodun Ayodeji Abioye1,2,                                                  Dayo Adeyemi Isadare1,2, Kunle Joseph Akinluwade1,2,* 1Department of Engineering, Prototype Engineering Development Institute (PEDI), Ilesa, [National Agency for Science and Engineering Infrastructure, NASENI] Nigeria 2Department of Materials Science and Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria  Abstract  There have been reported cases of the crusher jaw failure due to the high level of impact, tear and shear stresses experienced by the crusher jaw during service. The purpose of this paper is to select a suitable candidate material for the design of crusher jaw that can sustain fracture by any of the three modes of failure – tear, shear and impact at low cost using CES EduPack. Keywords  Crusher jaw, Material selection, CES EduPack, Fracture, Comminution  1. Introduction The mining and preparation of ore for extraction of the valuable minerals and production of a commercial end product of such minerals is called mineral processing or ore dressing. Apart from regulating the size of the ore, it is a process of physically separating the grains of valuable minerals from the gangue minerals, to produce an enriched portion, or concentrate, containing most of the valuable minerals, and a discard, or tailing, containing predominantly the gangue minerals (Wills and Atkinson, 1991). Mineral processing is the art of treating crude ores and mineral products in order to separate the valuable minerals from the waste rock, or gangue. It is the first process that most ores undergo after mining in order to provide a more concentrated material for the procedures of extractive metallurgy. The primary operations are comminution and concentration. The first mechanical stage in mineral processing is comminution which involves liberation of valuable minerals from the gangue. It is usually a dry operation carried out in two or three stages. The large lumps of the run mines are reduced in the primary crushing stage; this can reduce the lump of 1.5m to 10-20 cm using jaw crushers. Primary crushers are commonly designed to operate 75% of the available time, mainly because of interruptions caused by insufficient crusher feed and by mechanical delays in the crusher (Lewis, et.al, 1976). The reclaiming operations of the primary crusher products from the ore storage to the disposal   * Corresponding author: jakinluwade@yahoo.com (Kunle Joseph Akinluwade) Published online at http://journal.sapub.org/ijme Copyright © 2015 Scientific & Academic Publishing. All Rights Reserved  of the final crusher product involves the secondary crushing process, it is usually between 0.5 and 2cm. the secondary plant consists of appropriate crushers and screens, this is one or two size reduction stages, although more than two size reduction stages may be involved in secondary crushing if the ore is extra hard or in a case to minimize the production of fines. For slippery and tough ore, the tertiary crushing stage is usually substituted by coarse grinding in rod mills. The heavy duty machines use in the first mechanical stage of comminution are mainly jaw crushers. The distinctive feature of this class of crusher is the two plates which open and shut like animal Jaws (Grieco and Grieco, 1985), this jaw is called crusher jaw. The crusher jaws are set at an acute angle such that one jaw is pivoted and the other jaw is fixed. The pivoted jaw swings around the pivot and make impact on the fixed jaw, crushing the fed lumps in the jaw crusher.  Essentially, the task of selection is that of matching the choice of material to the requirements of the design (Ashby, 2005 and Charles et.al., 1997) Novel or well selected materials provide designers with excellent features. For instance, new materials offer promising perspectives in assisting automotive engineers to achieve improvement in vehicle fuel efficiency (Hemanth, et. al, 2011). They have been reported cases of the crusher jaw failure due to the high level of impact, tear and shear stresses experienced by the crusher jaw during service. The purpose of this paper is to select a suitable candidate material for the design of crusher jaw that can sustain fracture by any of the three modes of failure – tear, shear and impact at low cost using CES EduPack. The CES material and process selection software is an example of such a computer implementation (Ashby, 2005). Other analytical techniques may also be  18 Adelana Rasaki Adetunji et al.:  Material Selection for Crusher Jaw in a Jaw Crusher Equipment   adopted for various designs (Chan and Zhou, 1994 and Dieter, 1991).  2. Methodology The method of Function-Objectives-Constraints used by Akinluwade et al., (2015b) was applied in this study. The essentials of the study methodology are described in the next sub-sections. 2.1. Design and Function An impact mechanism was designed in Pro- Engineer (Pro-E) to simulate the loading conditions of a typical jaw crusher. It was deduced that a load of 3.28 x 108 Pa may cause failure of the hammer. CES EduPack was applied to select materials for the crusher jaw using the Function-Objectives-Constraints approach. The specific function of a crusher jaw is to propagate and sustain fracture by any of three modes of failure—tear, shear and impact. 2.2. Constraints and Objective Constraints represent crucial non-negotiable design conditions to be met. Constraints for the design of the crusher jaw are: Contact stress must not cause damage to either surface; toughness (for pivots exposed to shock loading) not be lower than 1.3 x 108 Pa.m0.5; thermal expansion (for high frequency crushers) not beyond 10 x 10-5; hardness not lower than 4.9 x 109 Pa with yield strength not beyond 1.80 x 109 Pa and cost not beyond 10 USD/Kg. Technical constraints were deduced from dynamic simulation while cost constraint is an administrative decision. Objectives represent what the design is required to maximize, minimize or maintain in its function (Akinluwade, et al., 2014b). Accordingly, the crusher jaw is require to propagate and sustain fracture by any of three modes of failure—tear, shear and impact. 3. Result and Discussion For the purpose of this application where preference is given for impact strength, all material families other than steel were screened off. The selection collection now parades stainless steel, low alloy steel, tool steel and maraging steel. Ranking was done on the basis of Fig 1 (Yield strength as a function of fracture toughness), Fig 2 (Fracture toughness as a function of price), Fig 3 (Yield strength as a function of price), Fig 4 (Yield strength as a function of thermal expansion coefficient), Fig 5 (Hardness (Vickers) as a function of density) and Table 1 (Material properties values considered for selected candidate materials). The final material selected is Low alloy steel AISI 9255 tempered at 205°C and Oil quenched, although it ranked fourth in fracture toughness, it has the second highest yield strength with the second lowest density, it has low hardness when compared with tool and stainless steel (the hardness is enough to crush silica lump) and is the cheapest. The choice of Low alloy steel AISI 9255 tempered at 205℃ and Oil quenched gives better performance while minimizing cost.  Figure 1.  Yield strength as a function of fracture toughness   International Journal of Materials Engineering 2015, 5(2): 17-22 19   Figure 2.  Fracture toughness as a function of price  Figure 3.  Yield strength as a function of price  20 Adelana Rasaki Adetunji et al.:  Material Selection for Crusher Jaw in a Jaw Crusher Equipment    Figure 4.  Yield strength as a function of thermal expansion coefficient Table 1.  Material properties values considered for selected candidate materials Materials   Density (Kgm-3) Yield Strength (Pa) Fracture Toughness (Pa.m0.5) Thermal Expansion (Strain/°C) Hardness (Pa) Cost (Usd/Kg)  Maraging steel,280(300)  7.96e3  2e9  8.5e7  1.04e-5  5.39e9  10.4  250 maraging steel  7.96e3  1.81e9  1.3e8  1e-5  4.71e9  10.3  Tool steel AISI A3 (oil hardening cold work)  8.08e3  2.37e9  2.03e7  1.18e-5  8.24e9  10.1  Tool steel AISI 06 (oil hardening cold work)  7.77e3  2.21e9  2.15e7  1.18e-5  7.85e9  4.51  Low alloy steel AISI 9255 tempered at 205°C and oil quenched   7.9e3   2.26e9   3.5e7   1.3e-5   6.47e9   0.882  Low alloy steel AISI 4340 tempered at 205°C and oil quenched   7.9e3   1.85e9   6.6e7   1.3e-5   5.64e9   1.36  Stainless steel martensitic AISI 44°C  7.9e3  2.09e9  2.8e7  1.1e-5  6.77e9  4.37     International Journal of Materials Engineering 2015, 5(2): 17-22 21  Table 2.  Selection consideration for shortlisted materials (Based on Figs. 4, 5 and 6) Materials Strength Comment Low alloy steel AISI 9255 tempered at 205°C and Oil quenched Cheapest  It ranked fourth in fracture toughness, it has the second highest yield strength with the second lowest density, it has low hardness when compared with tool and stainless steel (the hardness is enough to crush silica lump)  Tool steel AISI 06 (Oil hardening cold work)  Lowest density  It ranked third in yield strength, second highest in hardness with the lowest density, low fracture toughness but could still perform.  Stainless steel Martensitic AISI 44°C  Same density with low alloy steel  It ranked third in hardness, thermal expansion and cost with second highest in density. Fourth in yield strength but still fall within performance range  Low alloy steel AISI 4340 tempered at 205°C and oil quenched  Second cheapest and same density with stainless steel  It ranked third in fracture toughness and relative hardness  Tool steel AISI A3 (oil hardening cold work)  Highest yield strength and hardness  It has highest density, lowest fracture toughness and relatively expensive which may limit its use. In extreme case of high yield strength and hardness it can be recommended  250 Maraging steel  Highest facture toughness and lowest thermal expansion coefficient.  Consideration could be given if the jaw crusher would be operating at high temperature where durability is necessary due to high fracture toughness and low thermal expansion is necessary but the cost may limit its use. It has the lowest yield strength Maraging steel,280(300) Second highest fracture toughness and second lowest thermal expansion coefficient  It very expensive with fair hardness and yield strength.  Figure 5.  Hardness (Vickers) as a function of density  22 Adelana Rasaki Adetunji et al.:  Material Selection for Crusher Jaw in a Jaw Crusher Equipment   4. Conclusions The study concluded that Low alloy steel AISI 9255 tempered at 205°C and oil quenched is the material choice that maximizes performance and minimizes cost for crusher jaw in applications whose service requirements are bounded by the stated constraints. This choice lowers production cost appreciably while also upholding performance in all essential aspects of the service environment.  REFERENCES [1] Akinluwade, K. J., Ogwu, G. E., Badamasi, O. T., Taiwo, A. T., Adetunji, A. R. and O. O. Adewoye. (2014b). Material Selection for Axial Spring in a Prototype Cam-Follower Mechanism. British Journal of Applied Science & Technology 4(22): 3134-3142. [2] Akinluwade, K. J., Omole, F. O., Isadare, D. A., Adesina, O. S., Adetunji, A. R. (2015b) Materials Selection for heat sinks in HPC microchip-based circuitries. British Journal of Applied Science & Technology, 7(1): 124-133, 2015. [3] Wills, B.A. and Atkinson, K. (1991). The development of minerals engineering in the 20th century, Minerals Engng., 4(7-11), 643. [4] Lewis, F.M., Coburn, J.L., and Bhappu, R.B. (1976). Comminution: A guide to size-reduction system design. Min. Engng., 28(Sept.), 29. [5] Grieco, F.W. and Grieco, J.P. (1985). Manufacturing and refurbishing of jaw crushers, CIM Bull., 78(Oct.), 38. [6] Ashby MF. Materials Selection in Mechanical Design; 3rd edition. Butterworth Heinemann, Oxford, UK; 2005. [7] Charles JA, Crane FAA, Furness JAG. Selection and Use of Engineering Materials;3rd Edition. Butterworth Heinemann Oxford: UK; 1997. [8] Hemanth Kumar, Swamy TR, Chandrashekar RP, Taguchi TK. Technique for the Simultaneous Optimization of Tribological Parameters in Metal Matrix Composite. Journal of Minerals & Materials Characterization & Engineering. 2011;10(12):1179-1188. [9] Chan SL, Zhou ZH. Second-Order Analysis of Frames Using a Single Imperfect Element per Member. Journal of Structural Engineering, ASCE. 1994;120(6):703-717. British Journal of Applied Science & Technology, 4(22): 3134-3142, 2014 3142 [10] Dieter GE. Engineering Design, a Materials and Processing Approach; 2nd edition. McGraw-Hill: New York, USA; 1991.  View publication stats

Material Selection for Crusher Jaw in a Jaw Crusher Equipment

http://eprints.covenantuniversity.edu.ng/11248/1/26%20Material%20Selection%20for%20Crusher%20Jaw%20in%20a%20Jaw%20Crusher%20Equipment.pdf

Material Selection for Crusher Jaw in a Jaw Crusher Equipment

Abstract

Similar works

Full text

Available Versions

Covenant University Repository