This work presents the results of an experimental study performed on the mechanical behavior of concrete manufactured with ceramic recycled aggregates (CRA), from precast ventilation ducts, that once made have been rejected by defective. The ultimate objective is to use these wastes to manufacture prestressed concrete joists used in building floors. The coarse fraction and the fine fraction have been considered. The work has been carried out in three phases: characterization of the material, characterization of concrete with CRA and manufacturing and testing of prestressed joists. With the results obtained it is determined the influence of the ceramic recycled aggregate on the properties analyzed. There are not enough studies about prestressed elements that include the replacement of the aggregate in the fine fraction. In view of the results obtained could both of fine and coarse fraction can be used in these applications

FERNÁNDEZ ARIAS P. J

LÓPEZ COLINA PÉREZ C

LÓPEZ GAYARRE F

PANI, LUISA

SERRANO LÓPEZ M

LÓPEZ GAYARRE F

FERNÁNDEZ ARIAS P. J

LÓPEZ COLINA PÉREZ C

SERRANO LÓPEZ M

Archivio istituzionale della ricerca - Università di Cagliari

INFLUENCE OF CERAMIC RECYCLED AGGREGATES ON THE PROPERTIES OF PRESTRESSED PRECAST CONCRETE ELEMENTS F. LÓPEZ GAYARRE*, P.J. FERNÁNDEZ ARIAS*, C. LÓPEZ-COLINA PÉREZ*, M. SERRANO LÓPEZ* AND L. PANI** * Departamento de Construcción e Ingeniería de Fabricación, University of Oviedo, Spain  ** University of Cagliar, Italy SUMMARY: This work presents the results of an experimental study performed on the mechanical behavior of concrete manufactured with ceramic recycled aggregates (CRA), from precast ventilation ducts, that once made have been rejected by defective. The ultimate objective is to use these wastes to manufacture prestressed concrete joists used in building floors. The coarse fraction and the fine fraction have been considered. The work has been carried out in three phases: characterization of the material, characterization of concrete with CRA and manufacturing and testing of prestressed joists. With the results obtained it is determined the influence of the ceramic recycled aggregate on the properties analyzed. There are not enough studies about prestressed elements that include the replacement of the aggregate in the fine fraction. In view of the results obtained could both of fine and coarse fraction can be used in these applications.  1. INTRODUCTION Society is increasingly aware of the importance of their actions and therefore demand new proposals aimed at increasing the degree of sustainability in all its activities. Construction is one of the main human activities where a very large volume of waste were generated. It is essential advancing the creation of new techniques and materials to make it a less aggressive activity with the environment. The term “sustainable construction” was defined in the “First International Conference on Sustainable Construction” (1994 - Florida) by C. Kibert as “the creation and responsible management of a healthy built environment based on resource efficient and ecologicalprinciples” (Kibert et al., 1994). Construction and demolition wastes (CDW’s) constituted in 2010, in Europe, 34.4% of the total waste, which is equivalent to an amount of 860 million tons (Eurostat Yearbook, 2013) from which approximately 66% was ceramic or concrete waste (CEDEX, 2010). Although these residues are mostly inert or comparable to inert, Proceedings Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium S. Margherita di Pula, Cagliari, Italy; 5 – 9 October 2015  2015 by CISA Publisher, Italy  represent a serious environmental problem because of their huge volume. They are often accumulated with low environmental control and there is an overexploitation of natural resources by rejecting materials which with suitable treatment could be reintroduced into the production process. In the field of prefabricated components, several studies were conducted in different countries regarding to the use of recycled concrete. Such as paving blocks (Poon and Chan, 2006; Soutsos et al., 2011), pavement flags (Soutsos et al., 2012; Jankovic et al., 2012), building blocks (Soutsos et al., 2011; Xiao et al., 2011), kerbs and hollow blocks for flooring (López et al., 2013). In the study here presented was introduced the use of ceramic recycled aggregates (CRA) in the manufacture of prestressed joists for flooring systems. It has replaced both the coarse fraction and the fine fraction of natural aggregates (González-Corominas and Etxeberría, 2014). Should be noted that, at present, the rules in force in Spain (EHE-08, 2008) prohibits the use of recycled aggregates in prestressed elements. 2. CHARACTERIZATION OF THE MATERIAL Cement used for specimens and joists was CEM I 52.5 N. Its 2 days compressive strength is 45.6 MPa and 28 days compressive strength is 60.3 MPa. Cement used for nerve-beams was CEM III 42.5 N/SR. Its 2 days compressive strength is 20.7 MPa and 28 days compressive strength is 56.2 MPa. Natural limestone aggregates have been used. Their properties are listed in Table 1. Grading curves of natural and recycled aggregates are shown in Figure 1.  Ceramic recycled aggregates (CRA) come from clay ceramic blocks used in the construction of ventilation ducts (Figure 2a) that once made have been rejected by defective (Pérez, 2011). The original parts are manufactured under industrial quality controls and not used in any work. By this fact the presence of unusable elements is reduced. The ceramic elements are processed in a recycling plant (Figure 2b) to reduce them and classify them by screening. Thus the appropiate particle size distributions are obtained (Figures 2c and 2d). In order to characterize the material, granulometry (UNE 933-1), water absorption and density (UNE 1097-6), Los Angeles coefficient (UNE 1097-2) and sand equivalent (UNE 933-8) were determined. These properties are shown in Table 2. Table 1: Properties of aggregates  Property STANDARD Natural gravel 4/10 mm Washed sand 0/4 mm Sand        0/4 mm Water absorption [%] EN 1097-6 1 0.6 0.5 Particles density (ssd) [g/cm3] EN 1097-6 2.65 2.57 2.69 Los Ángeles coefficient EN 1097-2 - - - Sand equivalent EN 933-8 - 75.5 87  Proceedings Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium S. Margherita di Pula, Cagliari, Italy; 5 – 9 October 2015  2015 by CISA Publisher, Italy  Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium    Figure 1: Grading curves of natural and recycled aggregates Table 2: Properties of CRA by size    Property STANDARD CRA     4/31.5 mm CRA       0/4 mm Water absorption [%] EN 1097-6 14.5 10.8 Particles density (ssd) [g/cm3] EN 1097-6 2.21 2.31 Los Ángeles coefficient EN 1097-2 36 36 Sand equivalent EN 933-8 - 88    Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium      2a.- Ceramic wastes  2b.- Recycling plant     2c.- Waste processed  2d.- Detail of particle size Figure 2: Waste processing 3. CHARACTERIZATION OF CONCRETE WITH CRA It proceeded to characterizing physical and mechanical the concrete made with recycled aggregates ceramic (CRA).  The substitution of natural aggregate by the CRA was made in volume. The substitution levels were 20%, 35%, 50%, 70% and 100%. A control batch was made with natural aggregates. The control concrete dosage corresponds to that used in the prefabrication of prestressed joists (Table 3). The concrete is dry consistency (Figure 3a) with a seat 0-2 cm on the Abrams cone (UNE-EN 12350-2) and a water/cement ratio of 0.355. In the other batches the natural aggregate was replaced by the CRA in the indicated percentages.             Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium   Table 3: Mix proportions per m3 of concrete  The manufacturing of cylindrical specimens of 15 cm diameter and 30 cm in height (Figure 3b) was carried out compacting it using a shaking table. The samples were removed of its mould after 48 h and introduced in a curing chamber for 28 days at 20 ° C and a relative humidity of 95%. Subsequently the concrete density (UNE-EN 12390-7) and water absorption (UNE-EN 13369:2013) were determined (Figure 4). Compressive strength tests were performed (UNE-EN 12390-3) (Figure 5) and tensile splitting strength was determined (UNE-EN 12390-6).  The average values obtained are shown in Table 4. Comparative graphics are shown in Figure 6. Table 4: Properties of hardened concrete    Substitution Cement Water Natural grave 4/10 mm Washed sand 0/4 mm Sand 0/4 mm CRA [%] [kg/m3] [l/m3] [kg/m3] [kg/m3] [kg/m3] [kg/m3] 0 400 142.0 810.0 1158.0 70.0 0.0 20 400 176.5 648.0 926.4 56.0 307.6 35 400 202.4 421.2 602.2 36.4 538.3 50 400 228.2 210.6 301.1 18.2 769.1 70 400 262.7 63.2 90.3 5.5 1076.7 100 400 314.4 0.0 0.0 0.0 1538.1  Substitution Density Water absorption Compressive strength Tensile splitting strength [%] [kg/m3] [%] [MPa] [MPa] 0 2383 5.00 63.6 3.95 20 2338 5.90 55.6 4.32 35 2250 8.00 51.3 3.75 50 2231 10.90 59.0 2.92 70 2154 11.10 46.8 3.47 100 1999 14.70 40.1 2.77    Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium      3a.- Abrams cone  3b.- Cylindrical specimens Figure 3: Manufacturing of concrete       5a.- Start  5b.- End Figure 5: Compressive strength test     Figure 4: Water absorption test     Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium                                   6a.- Density                                                            6b.- Water absorption     6c.- Compressive strength  6d.- Tensile splitting strength  Figure 6: Properties of hardened concrete. Comparative graphics  4. MANUFACTURING AND TESTING OF PRESTRESSED JOISTS In the last stage four sets of prestressed joists with different substitution levels, and a series of natural aggregate control were made.  The joists were manufactured on the premises of a precast concrete specialized company that collaborate with the project (Figure 7). It used the dosage that reflected in Table 3. The manufacturing process involves extending prestressing cables along a prestressing bed. The prestressing cables were fixed at the ends and then they were tensioned by hydraulic jacks. A machine on rails poured concrete by vibrocompaction. After reaching the minimun resistance for concrete, the prestressing is transferred by cutting the cables. Prestressed joists with inverted-t section were made (Figure 8a), of 110 mm of width and 105 mm in height. The prestressing comprises three prestressed cables placed in the F4 and F1 positions (Figure 8b), of 5 mm diameter, Y1770C steel with 1600 N/mm2 of yield strength. Prestressing parameters are shown in Table 5. During manufacturing process of the prestressed joists, an excess water respect to the dosage of 35% replacement percentage was detected.  0015304560750 20 35 50 70 100Compressive strength (MPa)% substitution0123450 20 35 50 70 100Tensile splitting strength (MPa)% substitution  Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium   In order to compare the effect of the percentage of substitution on the behavior of the entire section two nerve-beams for each percentage of substitution were made. It considered 200 cm on length, 20 cm in height and 70 cm of width in the upper.    7a.- Manufacturing process  7b.- Joists detail Figure 7: Prestressed joists manufacturing Table 5: Prestressing parameters     8a.- Geometry  8b.- Prestressing positions  Figure 8: Joist section Three types of tests were performed:  Type 1: Test on 400 cm length joists supported at two points and under two point loads located at L / 3 from the supports till break occurs (Figure 9). Speed test was fixed in 15 N/s. Tests were Initial tension [Mpa] 1350 Total losses [%] 28,8 Minimun resistance for tansfer [Mpa] 19    Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium   performed at 90 days. The rupture occurs mainly by bending, with cracks that raise from the bottom of the joists.  The cracks were located within de central third of the joist.  Type 2: Test on 400 cm length joists supported at two points and under one point load near the support till break occurs (Figure 10). Speed test was fixed in 15 N/s. Tests were performed at 90 days. The rupture occurs mainly by shear, with cracks at 45º, from the support to the load point.  Type 3: Test on 200 cm length nerve-beams supported at two points under one point load locates at L/2 from the supports till breaks occurs (Figure 11). Speed test was fixed in 50 N/s. The rupture occurs mainly by bending, with cracks that raise from the bottom of the nerve-beam.       9a.- Start  9b.- End Figure 9: Type 1 test    10a.- Start  10b.- End Figure 10: Type 2 test      Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium           Figure 11: Type 3 test Once the tests ended, proceeded to determine the influence of the degree of substitution on the values of the breaking load. Breaking loads are shown in Table 6. Comparative graphics are shown in Figure 12. Currently being conducted durability tests on samples of the joists subjected to various types of environment. Are also being conducted determination of resistance to freezing and thawing.  The study of long-term deflections (shrinkage and creep) of prestressed concrete with CRA are ongoing. Table 6: Breaking loads Substitution Type 1 test  Type 2 test  Type 3 test [%] [kN] [kN] [kN] 0 6.5 17.3 35.448 20 7.4 18.6 36.588 35 7.2 10.8 32.516 50 7.0 14.5 35.712 70 6.7 12.6 37.114        11a.- Start  11b.- End   Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium     12a.- Type 1 test 12b.- Type 2 test    12c.- Type 3 test   Figura 12: Comparative graphics  5. CONCLUSIONS Based on data obtained from tests conducted were obtained the following conclusions:    Density of hardened concrete is reduced with increasing degree of substitution. For substitution of 70% the reduction is 9.6%.  Compared with natural aggregates, CRA have high percentage of water absorption. For substitution of 70% the increase is 22%.  Compressive strength of hardened concrete is reduced with increasing degree of substitution. For substitution of 70% the reduction is 26%.  Tensile splitting strength increases 9.4% for substitution of 20%, and it is reduced for the rest of cases. For substitution of 70% the reduction is 12%.  Bending breaking load of isolated joist is increased with increasing degree of substitution, although there is a maximum for values of 20%. This may be because the control concrete joist could have any defect. All values obtained are higher than those declared by the manufacturer for control joist.  Shear breaking load of isolated joist is increased 7.5% for substitution of 20% and it is reduced for the rest. For substitution of 35% the reduction is more pronounced. This may be due to   Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium   excess water during the manufacturing process. Shear breaking loads for substitution of 35% and 70% are lower than those declared by the manufacturer for control joist.  Bending breaking load of nerve-beam presents no large variations. Only for substitution of 20% it is reduced 8.3%.  AKNOWLEDGEMENTS The authors would like to express their gratitude to the Ministerio de Economía y Competitividad (Spain) for its support through the project ref. BIA2012-30915. REFERENCES Centro de Estudios y Experimentación de Obras Públicas (CEDEX), 'Catálogo de residuos. Ficha técnica: Residuos de Construcción y Demolición', (2010). EHE-08, Ministerio de Fomento, Instrucción de hormigón estructural, Ed. Centro de publicaciones Secretaría General Técnica Ministerio de Fomento, Madrid, 2008. Eurostat Yearbook, Waste Statistics (2013). Gonzalez-Corominas, A., Etxeberría, M., Properties of high performance concrete made with recycled fine ceramic and coarse mixed aggregates, Construction and Building Materials 68 (2014) 618–626. Jankovic, K., Nikolic, D. and Bojovic, D., 'Concrete paving blocks and flags made with crushed brick as aggregate', Construction and Building Materials 28 (2012) 659-663. Kibert, C. et al. 'Proceedings of the First International Conference on Sustainable Costruction', CIB-TG 16 (1994), Florida, EE.UU. López, F., López-Colina, C., Serrano, M.A. and López-Martínez, A., 'Manufacture of concrete kerbs and floor blocks with recycled aggregate from C&DW'. Construction and Building Materials 40 (2013) 1193-1199. Pérez Benedicto, José Ángel, Estudio experimental sobre propiedades mecánicas del hormigón reciclado con áridos procedentes de la no calidad en prefabricación, Tesis Doctoral, Universidad Politécnica de Madrid, 2011. Poon, C.S. and Chan, D., 'Paving blocks made with recycled concrete aggregate and crushed clay brick', Construction and Building Materials 20 (2006) 569-577. Soutsos, M.N., Tang, K. and Millard, S.G., 'Concrete building blocks made with recycled demolition aggregate', Construction and Building Materials 25 (2011) 726-735. Soutsos, M.N., Tang, K. and Millard, S.G., 'The use of recycled demolition aggregate in precast concrete products, Phase III: Concrete pavement flags', Construction and Building Materials 36 (2012) 674-680. Soutsos, M.N., Tang, K. and Millard, S.G., 'Use of recycled demolition aggregate in precast products, Phase II: Concrete paving blocks', Construction and Building Materials 25 (2011) 3131-3143. UNE 1097-2, 'Ensayos para la determinación de las propiedades mecánicas y físicas de los áridos. Parte 2: métodos para la determinación de la resistencia a la fragmentación', (1999). UNE 1097-6, 'Ensayos para la determinación de las propiedades mecánicas y físicas de los áridos. Parte 6: determinación de la densidad de partículas y la absorción de agua', (2001). UNE 83316, 'Ensayos de hormigón. Determinación del módulo de elasticidad en compresión',   Sardinia 2015, Fifteenth International Waste Management and Landfill Symposium   (1996). UNE 933-1, 'Ensayos para la determinación de las propiedades geométricas de los áridos. Parte 1: determinación de la granulometría de las partículas. Método del tamizado', (1998). UNE 933-8, 'Ensayos para la determinación de las propiedades geométricas de los áridos. Parte 8: evaluación de los finos. Ensayo del equivalente de arena', (2000). UNE-EN 12350-2, 'Ensayos de hormigón fresco. Parte 2: ensayo de asentamiento', (2006). UNE-EN 12390-2, 'Ensayos de hormigón endurecido. Parte 2: fabricación y curado de probetas para ensayos de resistencia', (2001). UNE-EN 12390-3, 'Ensayos de hormigón endurecido. Parte 3: determinación de la resistencia a compresión de probetas', (2009). UNE-EN 12390-6, 'Ensayos de hormigón endurecido. Parte 6: resistencia a tracción indirecta de probetas', (2005). UNE-EN 12390-7, 'Ensayos de hormigón endurecido. Parte 7: densidad del hormigón endurecido', (2001). UNE-EN 12390-8, 'Ensayos de hormigón endurecido. Parte 8: profundidad de penetración de agua bajo presión', (2001). UNE-EN 12504-4, 'Ensayos de hormigón en estructuras. Parte 4: determinación de la velocidad de los impulsos ultrasónicos', (2006). UNE-EN 13369:2013, Reglas comunes para productos prefabricados de hormigón', (2013). Xiao, Z., Ling, T.C., Kou, S.C., Wang, Q. and Poon, C.S., 'Use of wastes derived from earthquakes for the production of concrete masonry partition wall blocks', Waste Management 31 (2011) 1859-1866.      

Influence of Ceramic Recycled Aggregates on the Properties of Prestressed Precast Concrete Elements

Influence of Ceramic Recycled Aggregates on the Properties of Prestressed Precast Concrete Elements

Abstract

Similar works

Full text

Available Versions

Archivio istituzionale della ricerca - Università di Cagliari