Link to publisher's homepage at https://iopscience.iop.org/The microstructure of graphene oxide TiO2 (GO/TiO2) films on wettability and morphology properties were studied at different amount of Titanium isopropoxide with fixed amount of GO. GO/TiO2 thin films were prepared by using sol-gel method and deposited on glass substrate by spin-coating technique. The formation of GO/TiO2 was confirmed by using Fourier Transform Infrared Spectroscopy (FTIR) study while the morphology of GO/TiO2 was observed by Scanning Electron Microscopy (SEM) analysis. The hydrophilic/hydrophobic interactions of these films were examined by wettability test by measuring the water contact angle of the water drop on the surface of the coating. The wettability tests display that the contact angle of GO/TiO2 was increased from 90.0º to 118.7º after reduce the amount of titanium isopropoxide (TTIP). A small peaks of graphene and Ti were observed in the coated films and more pronounce peaks occur after the films were annealed. However, it was found that the annealing process does not improve the contact angle of the films as compared to the non-annealed films

Azliza, Azani

Dewi Suriyani, Che Halin

Kamrosni, Abdul Razak

Mohd Arif Anuar, Mohd Salleh

Mohd Mustafa Al Bakri, Abdullah

Muhammad Mahyiddin, Ramli

Norsuria, Mahmed

Suhaila, Sepeai

UniMAP Library Digital Repository

IOP Conference Series: Materials Science and EngineeringPAPER • OPEN ACCESSMicrostructure and Wettability of GrapheneOxide/TiO2 Thin Film Prepared via Sol-gel MethodTo cite this article: Azliza Azani et al 2019 IOP Conf. Ser.: Mater. Sci. Eng. 551 012099 View the article online for updates and enhancements.You may also likeGO Mediated TiO2 Nanotube Electrode forthe Photoelectrocatalytic Degradation ofPentachlorophenolHimadri Rajput, Amit Dhir and Vikas kumarSangal-Suppression of the coffee-ring effect byself-assembling graphene oxide andmonolayer titaniaPengzhan Sun, Renzhi Ma, Kunlin Wanget al.-Enhanced Photo-ElectrochemicalPerformance of Reduced Graphene-OxideWrapped TiO2 Multi-Leg NanotubesY. Rambabu, Manu Jaiswal and SomnathC. Roy-This content was downloaded from IP address 103.86.131.118 on 15/03/2022 at 03:32Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distributionof this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.Published under licence by IOP Publishing LtdJoint Conference on Green Engineering Technology & Applied Computing 2019IOP Conf. Series: Materials Science and Engineering 551 (2019) 012099IOP Publishingdoi:10.1088/1757-899X/551/1/0120991 Microstructure and Wettability of Graphene Oxide/TiO2 Thin Film Prepared via Sol-gel Method Azliza Azani1,*, Dewi Suriyani Che Halin1, Kamrosni Abdul Razak1, Mohd Mustafa Al Bakri Abdullah1, Mohd Arif Anuar Mohd Salleh1, Norsuria Mahmed1, Muhammad Mahyiddin Ramli1,2, Suhaila Sepeai3 1Center of Excellence Geopolymer & Green Technology (CEGeoGTech), School of Materials Engineering, Universiti Malaysia Perlis (UniMAP), Perlis, Malaysia 2School of Microelectronic Engineering, Universiti Malaysia Perlis (UniMAP), Perlis, Malaysia. 3Solar Energy Research Institute, The National University of Malaysia, Selangor, Malaysia. Email: dewisuriyani@unimap.edu.my Abstract. The microstructure of graphene oxide TiO2 (GO/TiO2) films on wettability and morphology properties were studied at different amount of Titanium isopropoxide with fixed amount of GO. GO/TiO2 thin films were prepared by using sol-gel method and deposited on glass substrate by spin-coating technique. The formation of GO/TiO2 was confirmed by using Fourier Transform Infrared Spectroscopy (FTIR) study while the morphology of GO/TiO2 was observed by Scanning Electron Microscopy (SEM) analysis. The hydrophilic/hydrophobic interactions of these films were examined by wettability test by measuring the water contact angle of the water drop on the surface of the coating. The wettability tests display that the contact angle of GO/TiO2 was increased from 90.0º to 118.7º after reduce the amount of titanium isopropoxide (TTIP). A small peaks of graphene and Ti were observed in the coated films and more pronounce peaks occur after the films were annealed. However, it was found that the annealing process does not improve the contact angle of the films as compared to the non-annealed films. 1.  Introduction Self-cleaning technology is among the technologies existing in today’s world. Self-cleaning coatings can be classified into two major categories which are hydrophilic and hydrophobic. Both of the categories involve water to self-clean themselves. In a hydrophilic coating, the water is made to spread surface in which a liquid on a solid surface makes a film over the surfaces. This will carry the dirt and other impurities, whereas in the hydrophobic coating, the water droplets slide and roll over the surfaces in which a water drops remain spherical on the solid surface thereby cleaning them [1]. Self-cleaning action of TiO2 over the past years that mainly discuss photocatalytic activity of TiO2. Titanium dioxide (TiO2) also known as titania is a white inorganic solid substance and also a most investigated materials in photocatalysis [2]. Pure TiO2 is obtained from ilmenite or leuxocene ore [3]. TiO2 holds many holds many possible applications including environmental and energy applications due to its excellent properties such as nontoxic, chemically stable, cheap, and easily available material, having a bandgap of 3.2 eV in the ultraviolet (UV) region [4].  However, there are limitataion in the photocatalytic eciency of pure TiO2 due to rapid recombination of photogenerated electron−hole pairs within TiO2 particles and lack of visiblelight absorption. Nobel metal deposition is one of the technique to overcome the limitation [5]. Suitable metal oxides deposition can enhance the  hydrophilic and hydrophobic porperties. Graphene oxide is the appropriate nobel metal to overcome the limitation due to its high surface area, high electrical conductivity (106 Scm−1), high carrier mobility (200,000 cm2 V−1 S−1) and ecient electron (e) transfer from TiO2 to graphene as its redox potential is just below the conduction band (CB) edge TiO2 [6]. Graphene film can provide improved surface properties such as friction coefficient [7], optical transmittance [8], and thermal conductivity [9].  Joint Conference on Green Engineering Technology & Applied Computing 2019IOP Conf. Series: Materials Science and Engineering 551 (2019) 012099IOP Publishingdoi:10.1088/1757-899X/551/1/0120992 In this study, we have investigated the effects of doping with graphene oxide on the hydrophilic property and hydrophobic property at different concentration of TiO2 as well as annealing process on the hydrophobicity of films. Sol-gel method is used to fabricate thin films due to its advantages such as easy, good homogeneity, ease of composition control and good optical properties. In particular, the sol-gel process is very efficient in producing thin and transparent multi-component oxide layers on various substrates such as stainless steel plates, alumina plates, glass panels and ceramic tiles. This work contributes to the comprehension of using modified TiO2 as self-cleaning materials. 2. Methodology  2.1 Materials All the chemicals used in the study were of analytical reagent grade available from several suppliers and were used as received without further purification. Graphene Oxide powder (4-10% edge-oxidized) and titanium tetraisopropoxide (TTIP) 97% was purchased from Sigma Aldrich, 2-propanol AR from QReC and Acetic Acid (99.5%) was from Daejung Reagent Chemicals. Hydrolysis reaction will result in precipitation by using precursors with strong reactivity towards water (eg. Titanium alkoxide). To overcome the percipitation, non-aqueous sol–gel techniques was used with titanium chloride or titanium alkoxides as a precursor. In case of the reactions using TiCl4 as a precursor, TiO2 forms under release of a large amount of HCl gas. Because HCl gas is toxic and chlorine impurities often remain in the final oxide material, titanium tetraisopropoxide are preferred as a precursor. In order to increase the stability of the solutions from titanium alkoxide precursors, it is not sufficient to switch to a non-aqueous sol–gel route. Indeed a chelating agent is still needed in a non-aqueous sol–gel route to obtain highly stable sols [10].  2.2 Substrate Preparation In this study, the glass slide with dimension size of 10 mm × 10 mm are used as substrate. The substrate was cleaned by using acetone and was placed in ultrasonic cleaner for 20 minutes in order to remove the contaminants on the glass surface. Then, the glass slides were rinsed with distilled water to remove the hydroxyl contaminants, and these glasses were then dried under room temperature for about 30 minutes. 2.3 Preparation of Graphene Oxide / TiO2 Firstly, titanium tetraisopropoxide (TTIP) was mixed with 2-propanol with two different ratios (TTIP: 2-propanol) which is 1:9 and 1:20 ratio with fixed loading of 1 mg of graphene oxide was added to the solution together. This resultant titanium precursor solution was stirred vigorously for 20 minutes. Then, 0.10 mL acetic acid was added to the solution. Continue vigorous stirring for 1 hour to obtain the final solution for the preparation of graphene oxide and TiO2 thin films. After the substrate was properly cleaned, the solution was deposited dropwise on the substrate at a speed of 2000 rpm for 30s by spin coating technique. The wet films were dried at 60ºC for 10 minutes, it was then annealed at 350ºC in the muffle furnace for 1 h. The heat treated films were stored in Petri dishes with lid for further use.  2.4 Characterization of Graphene Oxide/ TiO2 thin films The structure analysis was determined by FTIR spectra using Jasco FTIR 4200 spectrometer (Jasco International Co. Ltd., Japan) at the room temperature in the spectral range of 600–4000 nm. The surface morphology of the layers was observed and the microstructure of the films was determined by EDX technique by Surface Electron Microscopy (SEM) JSM-6460 LA Jeol Japan in School of Material Engineering, Universiti Malaysia Perlis (UniMAP). While all contact angle measurements were conducted using self made water contact angle apparatus with image capture by optical microscope and analyze by J Image software to obtain the angle.  3. Results and Discussion 3.1 Functional Group of GO/TiO2 The FTIR spectra of glass substrate and GO/TiO2 are shown in Figure. 1. Figure.1(a) shows the peak of Si-Si interaction at 2300 cm-1 and 2123 cm-1. As compared blank glass substrate with GO/TiO2, Fig.1(b) shows that an obvious peak was observed at 1399 nm-1 corresponded to C=O, indicating that the existed of GO in the films. The characteristic peaks of graphene oxide can also be found at 2900 cm-1 and 2700 cm-1 confirming that successfully prepared GO-TiO2. Moreover, Figure.1(b) shows the broad peak the broad Joint Conference on Green Engineering Technology & Applied Computing 2019IOP Conf. Series: Materials Science and Engineering 551 (2019) 012099IOP Publishingdoi:10.1088/1757-899X/551/1/0120993 absorptions at low frequencies below 1000 cm-1 were ascribed to the stretching vibrations of Ti–O–Ti bonds in TiO2. The peak in FTIR spectra observe similar to previous study by Martins et.al [11].   Figure. 1. FTIR spectra of (a) glass substrate and (b) GO/TiO2 film. 3.2 Surface Morphology of Graphene Oxide/TiO2 Figure 2 shows micrographs of two different ratio of GO/TiO2 thin films which are 1:9(GO/TiO2)  and  1:20(GO/TiO2) microstructure of the dispersion-distribution of graphene nanosheets within the matrix TiO2.  Fig. 2(a) shows a non-annealed film at low ratio of 1:9(GO/TiO2) while Fig. 2(b) and 2(c) were films for non- annealed and annealed at high ratio 1:20(GO/TiO2) respectively. It can be seen that the morphology 1:9(GO/TiO2) showed spongy morphology with most of the TiO2 particles were combined together with each other. Interestingly, Fig. 2(b) shows the film was denser and compact at high ratio 1:20(GO/TiO2). However, Fig. 2(c) exhibit that annealing process resulted of smaller particles with an even surface. It was clearly observed that TiO2 particles were agglomerated at higher ratio by supported of graphene oxide sheets.  The similar micrographs of GO/TiO2 can also be observed in previous study by Abdelmajid et.al [12].              Figure 2. Scanning Electron Micrscopy microgarphs of GO/TiO2 films at two different ratios, (a) 1:9 without annealing) , (b) 1:20(without annealing) and (c) 1:20 (annealing at 350ºC) 3.3 Chemical Analysis The chemical composition analysis was carried out on GO/TiO2 thin film sample by Energy Dispersive X-ray (EDX) analysis. The representative (EDX) pattern of a ratio 1:20(GO/TiO2) layer presented in Table 1, confirms the presence of C, O and Ti, indicating the formation of nanocomposite with high purity. The signal for C should mainly originate from the GO sheets, while those for Ti are from the TiO2 nanoparticles. The signal of O could contribute by TiO2 nanoparticles and a small amount of oxygen-containing groups on GO sheets. 3.4 Water Contact Angle The water contact angle was carried out to analyze the hydrophilicity of TiO2 composite film. Fig. 4 shows the water contact angle of the prepared films with a significant decrement after addition of graphene oxide due to alteration of interaction of hydrophilic/ hydrophobic of TiO2. Figure. 4(a) shows that the photograph of water contact angle on the blank substrate. It was found that the wettability tests display that the contact angle of GO/TiO2 non-anneal was increased from 90.0º to 118.7º after reduce the amount of TTIP as shown in Figure. 4(b) and Figure. 4(c) respectively. Table 2 shows all the water contact angle of GO/TiO2 thin film (a) (b) (c) 		Joint Conference on Green Engineering Technology & Applied Computing 2019IOP Conf. Series: Materials Science and Engineering 551 (2019) 012099IOP Publishingdoi:10.1088/1757-899X/551/1/0120994 at different ratio of TTIP with and without annealing process. This result shows that the films was subjected to high wettability due to addition of GO particles.   Figure 3. EDX diagram of ratio 1:20(GO/TiO2) film without annealing. Table 1. Table of EDX element of ratio 1:20(GO/TiO2) film without annealing Element Mass % Atomic % C   K 8.62 14.94 O   K 37.28 48.50 Si  K 42.58 31.55 Ti  K 11.51 39.39 Total 100.00 100.00  This can be confirmed in previous study by Narayanam et.al [13]. Furthermore, this finding was correlated to the amount of C, Ti and O2 as reported in the EDX result. Nevertheless, it was found that annealing process does not improve the water contact angle of the film as observed in Figure 4(d).             (a) (b) Joint Conference on Green Engineering Technology & Applied Computing 2019IOP Conf. Series: Materials Science and Engineering 551 (2019) 012099IOP Publishingdoi:10.1088/1757-899X/551/1/0120995              Figure. 4. Photograph of water contact angle of GO/TiO2 at different ratio of TTIP. Table 2. Water contact angle of GO/TiO2 at different ratio of TTIP Thin Film Water Contact Angle (º) Glass substrate without thin film 60.17 1:9 (GO/TiO2) - without annealing 90.00 1:20 (GO/TiO2) – annealing at 350º 114.44 1:20 (GO/TiO2) - without annealing 118.70 4.  Conclusions From the research, GO/TiO2 thin film were prepared in two different ratios of titanium isopropoxide with fixed amount of GO. The thin film was suscessfully prepared by sol-gel method using spin-coating deposition technique. Functional group analysis were obtained from FTIR spectra which indicated the presence of GO and TiO2. While for morphology analysis by SEM analysis shows that at lower ratio (1:9) showed spongy morphology with most of the TiO2 particles were combined together whereas at higher ratio (1:20)  shows that TiO2 particles was denser and compact.  The hydrophilic and hydrophobic properties are reflected from wettability test which shows that the thin film will become hydrophobic at the higher ration of TiO2 from 90.0º to 118.7º. From the wettability test also it was found that annealing process does not improve the contact angle of the film from hydrophilic to hydrophobic. Acknowledgements The author would like to acknowledge the support from the Fundamental Research Grant Scheme (FRGS)  under a grant number of FRGS/1/2017/TK07/UNIMAP/02/6 from the Ministry of Education Malaysia and under grant number of 03-01-02-SF1322 from Ministry of Energy, Science, Technology, Environment and Climate Change (MESTECC), Malaysia. The authors wish to thank the Center of Excellence Geopolymer & Green Technology (CEGeoGTech), School of Materials, Engineering, Universiti Malaysia Perlis, UniMAP for their partial support. References [1] Anandan S et al 2012  Applications 1. [2] Kusiak-Nejman E et al 2017 Catal. Today 287 189. [3] Damsyik N et al 2016 Politek. Kolej Komuniti J. Eng. Technol. 1 77. [4] Saleem A et al 2018 J. Electron. Mater. [5] Anandan S et a 2013 ACS Appl. Mater. Interfaces 5, 207. [6] Prabhu S et al 2017 Sol. Energy Mater. Sol. Cells 169 304. [7] Berman D et al 2014 17 31. [8] Kim K K et al 2010 Enhancing the conductivity of transparent graphene films via doping. [9] Zhang C  et al 2017 Nat. Publ. Gr 1.  [10] Abdul Razak K et al 2018 Solid State Phenomena 280 26. [11] Martins P M et al 2018 Compos. Part B Eng. 145 39. [12] Timoumi A et al 2018 11. 46. [13] Narayanam P K et al 2018 ACS Appl. Nano Mater. 1 5691.  (c) (d) 

Microstructure and wettability of Graphene Oxide/TiO2 thin film prepared via sol-gel method

http://dspace.unimap.edu.my:80/bitstream/123456789/74676/1/Microstructure%20and%20Wettability%20of%20Graphene%20Oxide%20TiO2%20Thin.pdf

Microstructure and wettability of Graphene Oxide/TiO2 thin film prepared via sol-gel method

Abstract

Similar works

Full text

Available Versions

UniMAP Library Digital Repository