ATM, Corporation

Electronic Publication Information Center

I ; TABLE OF CONTENTS English Page Specifications ............... .............. 3 Operating Instructions ..................... 4 Sonie Sifter and Accessory Care ..... . ..... 6 Replacement Parts . ....................... 7 Sieve Charts .............................. 8 Japanese .................................. 10 Far information concerning Dur production size Sonie Sitters, contact your ATM Representative or call1write to: ATM Corporation 645 S. 94th Place Milwaukee, WI 53214 (414) 453-1100 ATM CORPORATION MODEL L3P SONIC SIFTER PURCHASER'S 1 YEAR WARRANTY The ATM Corporation guarantees all its apparatus against delective material and workmanship lor aperiod 01 one year Irom the date 01 delivery. This guarantee is limited to repair or replacement 01 the delective apparatus in our lactory in Milwaukee, Wisconsin. The company does not assume responsibility or accept invoices lor unauthorized repairs to its apparatus. Under no circumstances shall the ATM Corporation be liable lor loss 01 prolits or other damages. The ATM Corporation is not responsible lor damage to apparatus due to improper installation or operation beyond its rated capacity (intentional or otherwise.) It is distinctly understood that the above covers all conditions under which ATM Corporation apparatus is sold. This warranty is valid only il the purchaser returns the attached warranty registration card (see back cover) to us within 30 days 01 purchase. ATM Corporation, 645 S. 94th Place, Milwaukee, WI 53214 2 SPECIFICATIONS FOR THE ATM SONIC SIFTER MODEL L3P POWER REQUIREMENTS Power Input ...... . GENERAL SPECIFICATIONS Stainless Steel Test Table Steel Cabinet and Frame Acrylic Sieve Frames, Spacers and Cone Aluminum Fines Collector Holder Alurninum and Stainless Steel Column Lock PORTABLE Weight: 34 Ibs. (15.4 kg) 120 Volts, 60 Cycles 110 Volts, 50 Cycles Height: 23" (58.4 cm) - requires less than 1 square foot of counter space and need not be fastened down. SCREEN SIZES U.S. Standard Sieves -In order to utilize the full capabilities of the ATM Sonic Sifter, it is recommended that the ATM sieves with the exclusive "See-Through" feature be used. Sieves are available in U.S. Standard Sieve Series and International Standards Organization mesh sizes fram No. 3Y2 through No. 400. When selecting sizes larger than No. 20 (850 microns). please consult your ATM Corporation representative. Precision Sieves - ATM can also supply sieves having mesh sizes fram 150 microns down to 5 microns. These sieves are made 01 electroformed nickel mesh. See Page 8 for a complete listing of ATM Sonic Sitter Sieves. OPERATING CONDITIONS This device will function properly at any humidity level withln the temperature limits of 0° to 120°F (-18°C to 50°C). However, for test repeatability, it is recommended that the ambient temperature and humidity be controlled. Sieves should never be subjected to temperatures beyond +125° F (52° C) and -45°F (-43°C). External vibrations of low energy level will have liltle effect upon the accuracy 01 results. Ta insure optimum results, the instrument should operate on a level surface. This helps to even out the layer of particles on each sieve. SIDE VIEW ~ DIMENSIONS FRONT VIEW 'f rr (14:9 cm) -, L Approx. , 11 7/." ~ 57/." Ooor Open t -;[1 "."., ~ I EI \ I 23" (58.4 cm) o@ol ~ ~ 10"---0 (25.4 cm) 4 • \ ~ 1 ~ 3 OPERATING INSTRUCTIONS 1) Place Sante Sifter on a level surface for operation. 2) Plug the line cord into the socket at the rear of the unit and then into a 120 volt, 60 cycle power source or a 110 volt, 50 cycle power source. 3) Turn the three position switch (See control panel diagram, Al to the 'SIFT-PULSE' position. At this point, the light at the rear of the sift chamber should be illuminated. 4) Select the sieves required for analysis. Up to six standard height, or three precision height sieves can be used at a time. 5) Weigh and record ta re weights of sieves, spacers, diaphragm, fines collectar and top cone. 6) Install the fines collector by selling the collector in the fines collector holder. Fasten the round plate at the bollom of the collector to the holder by slipping the keyhole slot over the fastener head. 7) Assemble the sieve stack with the coarsest sieve on thetop of the stack and the finest s,eve at the bollom. If less than six standard height or three precision height sieves are used, add spacers as required to 1ill out the stack to the proper height. Generally, the spacers should be placed toward the top of the sieve stack. Place the sieve stack on the fines collector holder with a fines collectar installed. 8) Place the top co ne on the sieve stack. 9) Seleet a proper weight 01 powder sam pie. When sieving materials larger than 38 microns, da not exceed 20 grams. When sieving materials smaller than 38 microns, da not exceed 10 grams. A good starting point for most tests is ane gram. The sam pie size can be gradually increased until the optimal combination 01 sam pie size, sift interval and amplitude is determined. 10) Place the powder sam pie on the top sieve. 11) Position the diaphragm (with ring protruding downwardl on the top cone. 12) Place column lock onto the sieve stack and press down until the latch bars lock onto the fines collector holder. 13) Position both the amplitude control and timer dial at '0'. (See control panel diagram, B & Cl 14) Place the sieve stack assembly in the sift chamber. Note: Be sure that the stack is positioned snugly between the pins. 15) To seal the sieve stack assembly, insert your thumb and forefinger into the openings between the lowest sieve and the colurnn lock bars and push outward on both bars. The latch bars will release to form a spring-loaded seal tor the enclosed air column. 4 SIEVE STACK //:;;;;;~;;:;;~~_ Column Lock OIaphragm Top Cone 6 Sieves - Stendard Depth or 3 Sieves Preclslon Depth Mesh Size Optlonal Fines Colle<:tor 1i~~~(j:- Holder - Fin •• CoUe<:.or 16) Close the door. Using the black scale on the timer dial for 60 cycle operation cr the red scale for 50 cycle operation, set the tirner dial to any arbitrary time interval. Ta set the time interval for future tests, loosen the stop pin lock screw and set the stop pin to the interval desired. Tighten the stop pin lock screw. Ta run future tests, just rotate the timerdial to the stop pin and push the start button. 17) Push the start button to begin the timer interva!. 18) Increase the Amplitude Control SLOWLY until the largest of the particles begin rolling on the sieve surface. Within seconds, material should start passing through the sieve. As the Sonic Sifter conceptallows each particle to be lifted off the sieve surface and set back down at a rate of 3600 times per minute, increasing the amplitude past this original setting will not add significantly to the sifting process. Excessive amplitude will cause fine material to cling to the sieve walls and stack parts. reducing the accuracy of the test resulls. Properly adjusted amplitude is particularly important with the Precision Sieve series. Due to the fragile nature of the elctroformed sieve material, excessive amplitude can cause sieve failures, 19) When no more material can be seen passing through the sieves, note the time interval that has elapsed. This time period should be used tor subsequent testing to ensure repeatable results. 20) Open the door and pull down on the latch bars to relock the sieve stack. Remove the stack trom the sift chamber and disassemble the sieve stack. Reweigh all parts and record. The percentage of material retained at any fraction can be easily calculated. 21) For help with special test procedure questions orassistance in developing efficient Sonic Sitter analysis procedures, contact the ATM Corporation. 8 CONTROL PANEL cP TI]" 'od',,'o, / ""j2""A ~ft ('iC ; S;fI 111' ';,} ,';j1 ., Off~ 7li. SI'V',' .. 00 mutes ~ plilud 7 S"" .,1100 A Lop Pln 5 SONIC SIFTER AND ACCESSORY CARE The L3P Sonic Sifter and accessories will perform satisfactorily for many years if the following basic care instructions are observed: 1) Far best results, sieve stack components and sieves should be cleaned in an ultrasonic cleaner of 150 watts cr less. General cleaning is best accomplished in a mild solution 01 dishwashing detergent ('JOY', or its equivalent) maintained at 75-80· F (24-27·C). II an ultrasonic cleaner is not available. immerse items to be cleaned in the same mild solution. 2) 00 not brush or use compressed air to clean any precision series sieve. This also applies to standard woven sieve cloth of 100 mesh cr finer. 3) Another cleaning option which has proven especially useful when running a large number of sieve tests during the day, is the use of FREON-TF as a cleaning solvent. The FREON-TF evaporates rapidly and causes no perceptible changes in tare weight, eliminating the need lor reweighing. The solvent also reduces the down-time experienced while waiting for water-washed sieves to dry. Approximately 3" (7.6 cm) 01 FREON-TF is placed in a 2000 ml beaker. The sleve is inserted edgewise into the beaker, and the entire beaker is placed in the ultrasonic cleaner. Gently rota te the sieve and remove from the solvent while the ultrasonic action continues. Just a lew words 01 caution are necessary. 00 NOT SUBSTITUTE ANY OTHER SOLVENT FOR FREON-TF. OTHER SOLVENTS WILL OAMAGE THE SIEVE FRAME ANO CLOTH, Other FREON compounds contain acetone and various alcohols which are incompatible with the acrylic material 01 the sieve. Also, do not clean the Latex parts (fines collector and diaphragm) in the FREON-TF as the latex compounds will disintegrate. 4) Due to the especially Iragile nature 01 the precision sieve cloth, do not touch the precision cloth with your fingers. Natural acids in the skin will permanently etch and discolor the mesh. Any contact with the sieve mesh increases the possibility 01 punctures or tears. 5) Always store precision sieves in the plastic storage box provided. 6) 00 not expose sieves to heat sources of any kind. 7) Fines collectors and diaphragms should be cleaned with mild detergent solutions only. Soillents of any kind will cause disintegration and failure of these natural Latex parts. Alter the diaphragm and collector have dried, dust lightly with a li ne talcum powder (NYTAL 200 or its equivalent) and store in protective foil pouch in a cool location. Avoid heat and direct sunlight on all Latex parts. 8) The Sonic Sifter cabinet, test chamber and aluminum stack components should be wiped clean periodically with a soft, damp cloth. 6 FInes Colle<:tor L:J.NS Dlaphragrn L:J.N2 Top Cone L:J.N3 Standard Spacer L:J.N4 ACCESSORIES AND REPLACEMENT PARTS* Column LO~:k:==:~~~~~_~_~f~~~~?==~:,....._~~~~ Dlaphr.gm Top Cone i Standard Spaeer Fine. Colleclor b. Fine. eolleetor HOlder~~ ~ Fine. CoUector HOlder ll-N6 Horizoniai Pulse Atlachmenl L3N8 Creates high speed shock wave to help elimlnate agglomeration Camptete Stack A .. embly LJ-N7 {meludes. column lock, one diaphragm. top cone. sei 01 6 standard spacers. one lines collector. eolleelor holder) Set 01 ODor Spring' X-327S37 ODor A .. embly X-399157 ODor (Only) X-327539 Handle (Only) 8-35374 Rubber Ooor Stop (Onlyj F-24027 Driver Assembly X-465030 lf Set 01 Bumper. 00 F24025 • Lamp X-3275S0 Lamp Sockel X-321548 lamp BaUasl ~ X-327549 ~ W.sher M-1554 ... Siop Screw • M-1553 Amplitude •• Knob X-327545 Ea . ... Time, Dlal ASiembly ~ X-321630 .. Siop PI,le (~ A.sembly X-327629 .. Time' Knob • X-321628 Lamp Cover Anembly X·327538 Power Cord A .. embly X·441329 . -0- \ :}.O ,,;= ::..:. AT_____ ~ Tlmer Hardw."t Repelr KU Z-34024 (.a. Included In Repa!r KII) OROERING INFORMATION - Your order must include the following information: a description of the part, the part number, as weil as the series letter and se rial number of the sitter. * Call the ATM Corporation for information concerning any parts not listed above. Orders may be placed by contacting your ATM Aepresentative or by calling/writing to: ATM Corporation 645 S. 94th Ploce Milwaukee, WI 53214 (414) 453-1100 7 SPECIAL SIEVES Stack column accomodates a maximum of 3 sieves Sieve Openlng Mlerans 32 25 20 SIEVE CHARTS Cat. No. Stalnless Steel L35M32 L35M25 L35M20 U.S. STANDARD SIEVES - In order to utilize the 1ull capabitities 01 the ATM Sonie Sitter lt is recommended that the ATM sieves with the exclusive "SEE-THRU" feature be used. Sieves are available in U.S. Standard Sleve Se ries and International Standards Organization mesh sizes from No. 31h through No. 400. When setecting sizes larger Ihan No. 20 (850 microns), please consult your ATM representative. PRECISION SIEVES - ATM can also supply sieves having mesh stzes from 150 microns down 10 5 microns. These sieves are made of electroformed nickel mesh. ORDER INFORMATION - When ordering sieves, speci1y the Catalog Number and the screen material. Orders may be placed by contacting your ATM Representative or by calling/writing to: ATM Corporation 645 5. 94th Place Milwaukee, WI 53214 (4t4) 453-1100 U.S. STANDARD SIEVES Stack column accomodates a maximum of 6 sieves Sieve Sieve Openlng No. mm 3.5 5.6mm 4 4.75mm 5 4.00mm 6 3.35mm 7 2.80mm 8 5.36mm 10 2.00mm 12 1.70mm 14 1.40mm 16 1.18mm 18 1.00mm 20 850/lm 25 710jJm 30 600/lm 35 500/lm 40 425/1m 45 355/1m 50 300/lm 60 250pm 70 21211m 80 laOpm 100 150/lm 120 125pm 140 106jJm 170 90/lm 200 75/1m 230 63/1m 270 53tJm 325 45/1m 400 38/1m Cat.No. Brass L3-B3.5 B4 B5 B6 B7 L3-B8 BIO B12 B14 B16 L3-B18 B20 B25 B30 B35 L3-B40 B45 B50 B60 B70 L3-B80 P100* P120* P140* P170* L3-P200* P230* P270* P325* P400* Cat. No. Stalnless Steel L3-53.5 54 55 56 57 L3-58 510 512 514 516 L3-518 520 525 530 535 L3-540 545 550 560 570 L3-580 5100 5120 5140 5170 L3-5200 5230 5270 5325 5400 * These sizes available in phosphor bronze or stainless steel only. NOTE - If you are in need 01 a special sieve configuration not listed above, please contact the ATM Corporation. 8 PRECISION SIEVESt Stack column accomodates a maximum 01 3 sieves Sieve Opening Cat. No. Mlcrons 150 L3-M150 125 M125 105 Ml05 100 Ml00 95 M95 90 L3-M90 85 M85 80 M80 75 M75 70 M70 65 L3-M65 60 M60 55 M55 50 M50 45 M45 40 L3-M40 35 M35 30 M30 25 M25 20 M20 15 L3-M15 10 Ml0 5 M5 t Precision sieves are double depth thus three will fit in the sieve stack. However. we recommend one sieve per separation in finer sizes due to the fragile nature 01 the electroformed nickel mesh. 

ATM Sonic Sifter Model L3P - manual

Abstract

Similar works

Full text

Available Versions

Electronic Publication Information Center