At European Centre of Nuclear Research (CERN), within the new Large Hadron Collider (LHC) project, measurements of magnetic flux with uncertainty of 10 ppm at a few of decades of Hz for several minutes are required. With this aim, a new Fast Digital Integrator (FDI) has been developed in cooperation with University of Sannio, Italy [1]. This paper deals with the final design tuning for achieving target uncertainty by means of experimental statistical parameter design

Arpaia, P

Giloteaux, D

Lucariello, G

Spiezia, G

CERN Document Server

EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCHLaboratory for Particle Physics(MTM)UNCERTAINTY REDUCTION VIA PARAMETER DESIGN OFA FAST DIGITAL INTEGRATOR FOR MAGNETIC FIELD MEASUREMENTP. Arpaia1, D. Giloteaux2, G. Lucariello1, G. Spiezia21 Università del Sannio, Dipartimento di Ingegneria, Benevento, Italy2 CERN, Accelerator Technology Department, Geneva, SwitzerlandCERN/AT 2007-25Presented at the Conference on Precision Electromagnetic Measurements (CPEM 2006)9-14 July 2006, Torino, ItalyDepartmental ReportCERN, Accelerator Technology DepartmentCH - 1211 Geneva 23SwitzerlandAt European Centre of Nuclear Research (CERN), within the new Large Hadron Collider (LHC) project,measurements of magnetic flux with uncertainty of 10 ppm at a few of decades of Hz for several minutes arerequired. With this aim, a new Fast Digital Integrator (FDI) has been developed in cooperation with University ofSannio, Italy [1]. This paper deals with the final design tuning for achieving target uncertainty by means ofexperimental statistical parameter design.30 August 2007UNCERTAINTY REDUCTION VIA PARAMETER DESIGN OF A FAST DIGITAL INTEGRATOR  FOR MAGNETIC FIELD MEASUREMENT   Pasquale Arpaia 1, David Giloteaux 2, Giuseppe Lucariello 1, Giovanni Spiezia 2  1 Dipartimento di Ingegneria, Università del Sannio, Corso Garibaldi 107, 82100 Benevento, ITALY. Ph : +39 0824 305804-17, Fax: +39 0824 305840, E-mail: arpaia@unisannio.it; gluck_78@yahoo.it; 2 CERN, Dept. AT (Accelerator Technology), Group MTM, CH 1211 Genève 23, Switzerland. Ph : +41 22 76 76635;  Fax: +41 22 76 76230, E-mail: {David.Giloteaux-Giovanni.Spiezia}@cern.ch   Abstract At European Centre of Nuclear Research (CERN), within the new Large Hadron Collider (LHC) project, measurements of magnetic flux with uncertainty of 10 ppm at a few of decades of Hz for several minutes are required. With this aim, a new Fast Digital Integrator (FDI) has been developed in cooperation with University of Sannio, Italy [1]. This paper deals with the final design tuning for achieving target uncertainty by means of experimental statistical parameter design.  Introduction In high-accuracy instrument design, accuracy is enhanced usually by selecting higher-quality components and imposing narrower variations to influence parameters. A different approach is used in control system and electronic circuit design, or in quality engineering [2]-[5]: the system output is made as much insensitive as possible both to component tolerances and to influence parameters by selecting a suitable system configuration. This is carried out through analysis techniques of system theory, range methods, or statistical experiment design. In any case, the same aim of only finding better nominal values of system components or design parameters is pursued, by avoiding a cost increase.  In this paper, a procedure of uncertainty reduction, as well as of optimization of metrological characteristics, through statistical experimental parameter design in the input range as a whole is proposed and applied to the abovementioned FDI [1]. The proposed method A measurement system can be formalized in terms of measurand parameters xj (j = 1, 2,..., m), design parameters ci (i = 1, 2,..., n), influence factors uj (j = 1, 2,..., r), and reading parameters yk (k = 1, 2,..., p) [6]. The ci are sampled in order to assume q levels (q = 1, 2, ..., z). The problem of uncertainty reduction is defined as to find the combinations of ciq  that reduce the reading variance without loss in other metrological performance [6]. The burden of this task is reduced by experimental fractional factorial plans [2]-[6].  The first step of the proposed approach is to choose a suitable objective function η. Under the hypothesis of parameter independency, the relationship between η and ci can be expressed by the following model:  εδµη ++= ∑=niiq1       (1) where µ is the overall mean of η for the experimental plan, δiq is the deviation from µ due to ciq, and ε stands for the uncertainty. Experimental results are then analysed by [2]: (i) analysis of mean (ANOM), in order to estimate the effects of the configuration options on the optimum attainment; and (ii) analysis of variance (ANOVA), in order to evaluate the relative weight of such options with reference to the uncertainty of the estimate, and to select only the most significant ones.   Experiments The proposed method was applied to the FDI developed at CERN, under the framework of a cooperation between Magnetic Tests and Measurement (MTM) Group and the Dipartimento di Ingegneria of University of Sannio [1].  At CERN, Portable Digital Integrators (PDIs), based on gain programmable voltage-to-frequency converters, have been used for 20 years successfully [7]. However, in most advanced applications of test and control for the LHC under construction, more constraining requirements of 10 ppm on integrated voltage measurement for an integration time of 1 s or more are needed for the measurement of magnetic field based on rotating coils. Other laboratories proposed full digital solutions [8]-[10], however drawbacks related to timing constraints still arise. The main sections of the FDI analog part are shown in Fig. 1: • the Programmable Gain Amplifier (PGA); • the 18-bit Analog-to-Digital Converter (ADC); • the Field Programmable Gate Array (FPGA); • the digital trimmer for the gain adjustment; • the Digital-to-Analog Converter (DAC) for the offset compensation. The input signal, picked up form the coil, is conditioned by the PGA and quantized and converted by the ADC; the digital signal is sent to a Digital Signal Processor (DSP) ADSP-21262 through the FPGA Xilinx Spartan III which represents the I/O processor of the FDI. The digital trimmer and the DAC operate in the calibration procedure for the adjustment of the selected gain and for the correction of the offset voltage. The list of the selected design parameters with the respective levels is shown in Tab. 1: fFPGA is the clock frequency of the FPGA, Vref is the external reference voltage of the ADC, AVDD is the ADC analog power input, while Vpow is the power voltage fo the instrumentation amplifier of the PGA, and Rgain is a resistor that contributes to the final value of RG, the sensing resistor of the PGA (Fig. 1).  1There are five parameters with three levels thus the experimental plan L18 [2]-[6] (Tab. 2) was selected. The chosen objective function was: ( )( )22 1log10 −+⋅−= fff µση          (2) each experiment (a row of the matrix) was replied nr = 30 times. In the presentation, the optimal combination of parameter level, carried out with ANOM test, and the terms that have gone over Fisher test on ANOVA for a significance level of 99 %, and the achieved uncertainty reduction is reported.  Acknowledgments This work was sponsored by CERN (European Organization for Nuclear Research) trough the agreement No K 120/AT/LHC with the Department of Engineering, University of Sannio, whose supports authors gratefully acknowledge. References [1] P. Arpaia, L. Bottura, et al., “A fast digital integrator for magnetic field measurements at CERN”, IEEE IMTC 2006, Sorrento (I), April 2006. [2] M. S. Phadke, “Quality engineering using robust design”, (Prentice Hall, Englewood Cliffs, NJ, 1989). [3] P. Arpaia, “Experimental optimization of flexible measurement systems”, IEE Proc. Sci Meas. Technol., Vol. 143, No. 2, March 1996. [4] P. Arpaia, P. Daponte, Y. D. Sergeyev, “A-priori statistical parameter design of ADCs by a local tuning algorithm of global optimisation”, Acts of 4th “IMEKO International Workshop on ADC Modelling and Testing ”, Bordeaux, France, 9-10 Settembre 1999, pp.236-244. [5] D. H. Wu, W. T. Chien, Y. J. Tsai, “ Applying Taguchi dynamic characteristics to the robust design of a piezoelectric sensor”, IEEE Trans. on Ultras., Ferroel. and Freq. Cont. Vol. 52 , Issue: 3, March 2005, pp. 480 – 486. [6] P. Arpaia, N. Polese, “Uncertainty reduction in measurement systems by statistical parameter design", IEEE IMEKO 2001, Lisbon, Portugal, September, 2001. [7] P. Galbraith, “Precision  electronics  for  field measurements: integrators”, CERN internal note 021120, 1985. [8] C. Evesque, “A new challenge in magnet axis transfer”, IMMW11 Brookhaven National Laboratory, September 1999. [9] Y. Kawamata, I. Yonekawa, K. Kurihara, “Development of an intelligent Digital Integrator for Long-Pulse Operation in a Tokamak”, 19th Symp. on Fusi on Engineering, 21-25 Jan. 2002, pp. 172 – 175. [10] R. Carcagno, J. Di Marco, S. Kotelnikov, M. Lamm, A. Makulski, V. Maroussov, R. Nehring, J. Nogiec, D. Orris, O. Poukhov, F. Prakoshin, P. Schlabach, J.C. Tompkins,G.V. Velev, “A fast continuous magnetic field measurement system based on digital signal processor”, 19th Magnet Technology, October 2005.  Table 1 – Control parameters with the respective levels Parameter Lev. 1 Lev. 2 Lev. 3 x1 fFPGA [MHz] 20 35 50 x2 ADC Vref [V] 4.09 4.096 5.02 x3 AVDD [V] 4.75 5.00 5.25 x4 Vpow 14.0 14.5 15.0 x5 Rgain [kΩ] 10 11.0 12 Table. 2 – Experimental Plan L18 (e: empty) Exp. x1 x2 x3 x4 x5 e e 7 e 1 1 1 1 1 1 1 1 1 2 1 1 2 2 2 2 2 2 3 1 1 3 3 3 3 3 3 4 1 2 1 1 2 2 3 3 5 1 2 2 2 3 3 1 1 6 1 2 3 3 1 1 2 2 7 1 3 1 2 1 3 2 3 8 1 3 2 3 2 1 3 1 9 1 3 3 1 3 2 1 2 10 2 1 1 3 3 2 2 1 11 2 1 2 1 1 3 3 2 12 2 1 3 2 2 1 1 3 13 2 2 1 2 3 1 3 2 14 2 2 2 3 1 2 1 3 15 2 2 3 1 2 3 2 1 16 2 3 1 3 2 3 1 2 17 2 3 2 1 3 1 2 3 18 2 3 3 2 1 2 3 1 Figure 1. Prototype  scheme.  2

Uncertainty Reduction Via Parameter Design of A Fast Digital Integrator for Magnetic Field Measurement

Abstract

Similar works

Full text

Available Versions

CERN Document Server