Oil-in-glycerol (O/G) emulsion was prepared in the presence of different

weight ratios of mixed Tween20-Span20 surfactants. O/G emulsion was

observed to form below 50 wt% of oil content at 3 wt% of mixed Tween20Span20

surfactants. Physical properties of the emulsion were determined by

using a microscope, particle counting and rheological measurement. An

attempt to correlate HLB values of mixed Tween20-Span20 with emulsion

stability was also carried out

Kuang Abdulah, Dzulkefly

Lim, Wen Huei

Suhaimi, Mohd Hamdan

Wan Mahamod, Wan Rusmawati

Universiti Putra Malaysia Institutional Repository

Pertanika J. Sci. & Techno\. 10(2): 153 - 160 (2002)ISSN: 0128-7680© Universiti Putra Malaysia PressEmulsion Properties of Mixed Tween20-Span20 inNon-Aqueous SystemlW. M. Wan Rusmawati, *%K. Dzulkefly, 3W.H. Lim & 48. HamdanlFaculty of Science and TechnologyUniversiti Pendidikan Sultan Idris (UPS!)2Department of ChemistryUniversiti Putra Malaysia (UPM)3Advanced Oleochemical Technology Centre (AOTC)Malaysia Palm Oil Board (MPOB)4Faculty of Science and TechnologyUniversity College TerengganuReceived: 27 June 2001ABSTRAKEmulsi minyak-dalam-gliserol (O/G) telah disediakan dari campuran surfaktanTween20-Span20 dengan nisbah berat yang berbeza. Emulsi O/G didapatiterbentuk bila kandungan minyak kurang dari 50 wt% dengan kepekatancampuran Tween20-Span20 3 wt%. Sifat-sifat flzikal emulsi ditentukan denganmengguna mikroskop, penganalisis partikal dan pengukuran reologi. Kajianperkaitan antara nilai HLB campuran Tween20-Span20 dengan kestabilanemulsi juga dilakukan.ABSTRACfOil-in-glycerol (O/G) emulsion was prepared in the presence of differentweight ratios of mixed Tween20-Span20 surfactants. O/G emulsion wasobserved to form below 50 wt% of oil content at 3 wt% of mixed Tween20-Span20 surfactants. Physical properties of the emulsion were determined byusing a microscope, particle counting and rheological measurement. Anattempt to correlate HLB values of mixed Tween20-Span20 with emulsionstability was also carried out.Keywords: Tween20, Span20, nonaqueous emulsion, droplets size, stability,rheologyINTRODUCTIONEmulsions have been defined as heterogeneous systems of one liquid dispersedin another in the form of droplets usually exceeding 0.1 !-lm in diameter. Thetwo liquids are immiscible, chemically unreactive, and form systems characterizedby a minimal thermodynamic stability. One of the important components formaking an emulsion is the emulsifier, and a systematic selection of emulsifiertype for a particular emulsion is frequently based on the hydrophilic-lipophilicbalance (HLB) concept (1). It is known that mixtures of emulsifiers can have*To whom correspondence should be addressedW. M. Wan Rusmawati, K. Dzulkefly, W. H. Lim & S. Hamdansynergistic effects in enhancing stability of emulsions. A suitable combinationof emulsifiers leads to a greatly enhanced stability as compared to individualemulsifiers (2). Various reasons have been given for this, such as formation ofintermolecular complexes at the oil/water (O/W) interface (3) and developmentof strong interfacial films that prevent coalescence by virtue of their highdilational elasticity (4).Water-in-oil (O/W) and oil-in-water (O/W) emulsions have been widelystudied since emulsion was recognized. In contrast, oil-in-glycerol (O/W)emulsion has not been fully explored and therefore remains rather limited.Thus, this paper presents some of the physical properties (emulsion stability,droplet size and flow behaviour) of a non-aqueous emulsion formed by mixingTween20 and Span20.MATERIALS AND METHODSMaterialsPolyoxyethylene (20) sorbitan monolaurate (Tween20) and sorbitan monolaurate(Span20) from Sigma were used as received. Glycerol (G) of 99.5% puritypurchased from Sigma was also used throughout the experiment. Mediumchain triglyceride (MCf) oil, obtained from a local manufacturer, was used asan oil phase.MethodsPreparation of EmulsionO/G emulsion was prepared by first dispersing a required amount of mixedemulsifier (Tween20-Span20) in glycerol (9.0 ml). The MCT oil (1.0 ml) wasthen added and the mixture was homogenised (using an IKA-T25 disperser) for3 min at 8000 rpm to produce an emulsion. The emulsions were kept at30.0±5°C for 24 hours to equilibrate before being analysed. The emulsifierswere blended together, to obtain HLB values within the range 8.7-16.7. HLBof mixed emulsifiers can be calculated as follows:HLBmixlUre = f HLBA + (1-1> HLBB (1)Where f is weight fraction of emulsifier A and (1-f) is weight fraction ofemulsifier B.Particle SizeThe O/G emulsions samples were viewed directly under a microscope (OlympusAX70) with a camera attached, and the stage of the microscope wasthermostatically controlled. The undiluted samples were placed on a slide andwere illuminated from below, i.e. transmitted light was used. The droplet sizesof emulsions were subjected to a laser light scattering instrument (MalvernZetasizer 5000) for particle size determination.154 PertanikaJ. Sci. & Techno!. Vol. 10 No.2, 2002Emulsion Properties of Mixed Tween2O-Span20 in on-Aqueous SystemViscosity MeasurementThe steady flow behaviour was studied using a Brookfield Rheometer (ModelDV-III), which was attached to a cone and plate sensor system. The sampleswere allowed to reach the required test temperature in a suitable sensor system.Subsequently, the rheometer was operated at a steady rate and the shear ratewas increased gradually from 1 and 250 ..1 and then decreased back to 1 ..lovera period of scanning time. The flow behaviour of O/G emulsions systemscontaining different MCT:G ratio at 3% wt/wt of mixed emulsifiers was studied.RESULTS AND DISCUSSIONThe results of emulsion stability through visual observation in Table 1 showedthat the emulsion was stable in the range of 10:90 to 30:70 of MCT:G ratios.The emulsions were unstable at higher content of MCT (i.e. 40:60 and 50:50 ofMCT:G ratios). This might be due to the collapse of oil droplets in theemulsion system. Comparison among different weight ratios of mixed surfactants,20:80 weight ratio of Tween20-Span20 system has the smallest stable emulsionregion (between 10:90 and 20:80 of MCT:G ratios) as observed under amicroscope. The decrease in emulsion region might be due to the strongrepulsion between Tween20 and Span20 at the oil-glycerol interface, which wasnot able to retain the increase of oil droplets in the system.Fig. 1 shows the variation of the emulsion droplets size of different lll..Bnumbers for 10:90 of MCT:G weight ratio. On the first day. the droplet sizeincreased with the increase of the HLB number. This means the increase of theHLB number - increase of Tween20 - played an important role in the incrementof oil droplet in the continuous phase. On the seventh day. it was observed thatthe oil droplet at lower HLB numbers (8 to 13) increased to about the size ofhigher lll..B numbers (13 to 16.7). This was due to the coalescence of the oildroplet cluster to form a more stable droplet. In contrast, there was no changein the droplet size of higher HLB number. The particle size was rather constantas compared to the first day. This suggests that the oil droplet in the emulsionTABLE 1Emulsion stability of mixed surfactants (3 wt%) in MCT/G emulsion systemsTween20-Span20 MCT-in-G (%)(HLB) 0:100 10:90 20:80 30:70 40:60 50:50100:0 (16.70) c1r S S S B B80:20 (15.11) c1r S S S B B60:40 (13.82) c1r S S S B B40:60 (12.26) c1r S S S B B20:80 (10.41) c1r S S B B B0:100 (8.60) c1r S S S B B* clr -clear solution; S - stable emulsion; B - emulsion breakPertanikaJ. Sci. & Techno!. Vo!. 10 0.2, 2002 155W. M. Wan Rusmawati, K. Dzulkefly, W. H. Lim & S. Hamdansystem was more stable even after seven days. This implied that the emulsionwas more stable with the increase of Tween20 as it did not affect the oil dropletsize.15001200Eca; 900NiiiQ)u 600t:<1la..30006-+-1 day-B-7 days8 10 12HLB number14 16 18Fig. 1: DIG emulsion in mixed surfactants system of various HLB values(MCT:G, 10:90 weight ratio)A similar phenomenon occurred in MCT:G of 20:80 weight ratio in mixedsurfactants system as shown in Fig. 2. On the fIrst day, the oil droplets increasedsteeply from 244 to 527 nm as the HLB number increased from 8 to 13.Further increase in HLB numbers from 13 to 16.7 did not show any signillcantincrease in droplet size. Mter seven days, the oil droplet sizes of lower HLB (8to 13) increased, whereas at higher HLB number, (13 to 16.7) the emulsionexhibited a rather constant droplet size. However, the droplet size of 20:80weight ratio of MGT:G system was larger than the 10:90 system. The weak oil-glycerol interface of the 20:80 weight ratio contributed to the instability of theoil droplet as more oil droplet coalescence produced large oil droplets.The oil droplet was further increased from 924 to 1061 nm (1st day) withthe increase of oil (MGT) content as shown in Fig. 3. However, at lower HLBnumbers, a rather consistent particle size was obtained after seven days. Incontrast, at higher HLB numbers, the droplet size increased. This increase ofsize was due to the contribution of oil (MGT) content in the OIG emulsionsystem. The results showed that the increment of oil was still able to maintainthe stability of emulsion except 20:80 weight ratio of Tween20-Span20 system.Fig. 4 shows the plotted shear stress versus shear rate of OIG emulsion ofdifferent Tween20-Span20 weight ratios in MGT:G (10:90) in the mixedsurfactants system. It was observed that the shear stress increased with theincrease of shear rate. All mixed Tween20-Span20 studies showed a similar flowbehaviour. The tangents of the curve indicate no changes in viscosity. The156 PertanikaJ. Sci. & Techno\. Vol. 10 No.2, 2002Emulsion Properties of Mixed Tween20-Span20 in Non-Aqueous System1015001200Ec 900GiN.(i;Q.lT.i 600tcrla..300a6--....1 day-e-1 (jays8 12HLB number14 16 18Fig. 2: OIG emulsion in mixed surfactants system of various HLB values(MCT:G, 20:80 weight ratio)1015001200Ec 900GiN(i;'"u 600f.''"Q..30006___ 1 day-B-7 days8 12HLB number14 16 18Fig. 3: OIG emulsion in mixed surfactants system of various HLB values(MCT:G, 30:70 weight ratio)viscosity is constant regardless of the shear rate that shows Newtoniancharacteristics. As oil content increased to 20:80 of MCT:G in the mixedsurfactant system, hysterisis loop was observed for all weight ratios of Tween20-Span20 mixtures except 0:100 and 20:80 of Tween20-Span20 (see Fig. 5). Thisindicates that the emulsion system was disturbed and unable to return to itsoriginal form. The network among oil droplets in the emulsion system wasbroken due to shear action. The increase of oil content in the emulsion systemPertanikaJ. Sci. & Techno!. Vo!. 10 No.2, 2002 157W. M. Wan Rusmawati, K. Dzulkefly, W. H. Lim & S. Hamdanincreases the network interaction among oil droplets. As a result, largerhysterisis loop was observed in the shear stress-shear rate curves except for 0: 100weight ratio of Tween2Q-Span20 mixtures as shown in Fig. 6.In general, yield stress increases with the increase of oil content in theemulsion system. The highest yield stress was observed in the system containing30:70 of MCT:G weight ratio (Fig. 7). In addition, the yield stress does not vary1000""- 100t:Z<Ii'f><lJ7j;m<lJ.c 1.0lj)Twccn:]O : Spa1l20___ 100:0-.-8020........... 40.60~20.80--0:10001o :;0 100 150Shear rate. 1isec200 250 300Fig. 4: Shear stress as a function of shear rate of different Tween2o-span20weight ratios in MCT:G (10:90) emulsion system1000E lO.n2:~20:BO__ 0:100G.lo 50 100 150Shea' late, 1fsec200 250 300158Fig. 5: Shear stress as a function of shear rate of different Tween2o-span20weight ratio in MCT:G (20:80) emulsion systemPertanikaJ. Sci. & Techno!. Vo!. 10 No.2, 2002Emulsion Properties of Mixed Tween20-Span20 in Non-Aqueous Systemsignificantly after storage for one week. Fig. 8 shows the variation of viscositywith HLB of the mixed Tween2Q-Span20 (3 wt%) emulsion systems afterapplying shear at 10 rpm. The viscosity of the emulsion decreases with the HLBnumber and increases with oil content in the mixture.100.0'"'""~10.01.0Tween20 : Sp/1Tl20___ 80:20- ..··60:40---- 40:60--0:1000.1o 50 100 150 200 250 300Sh~CH rRte. ~fs&cFig. 6: Shear stress as a junction of shear rate of different Tween20-Span20weight ratio in MCF:G (30:70) emulsion system5,--------------------..,-e-- 90'10 (1 dayj-.-80:20 (1 day)__ 70:30 (1 day)..._90·10 (1 week)--er- 80:20 (1 'NOCk)~- '10:30 (1 week)G:MCT----18161412108oL_~:::::::::i~=:::::5:~~::!~~~6HLB numbersFig. 7: Yield stress of DIG emulsions at different HLB numbers in 1 and 7 days.The emulsions were prepared using 3 wt % of mixed Tween20-Span20in different MCT:G ratiosPertanikaJ. Sci. & Technol. Vol. 10 0.2,2002 159W. M. Wan Rusmawati, K. Dzulkefly, W. H. Lim & S. Hamdan300G: IVICT~200o~~ii;c~,5 100___ 9tJ1{}t1 (j,iyi--..- 3020 \1 dayi-.-- iG.30 t1 auy)-e- 90.10 (1 weolk)-0-80:20 (1 wm~k)-e- iO:30 (1 wt:HK)---181610 12 14HLB numbers80'----.......----'---------"'"---""----....6Fig. 8: Viscosity of DIG emulsion of different HLB numbers at 10 rpm shear rate. Emulsionswere prepared using 3 wt% of mixed Tween2Q.-.Span20 in different MCT:G ratios andmeasured after 1 and 7 days storage.Non-aqueous emulsion of mixed suifactantsCONCLUSIONStable O/G emulsion was obtained between 10:90 and 30:70 of MCT:G weightratios. Further increase of oil content breaks the emulsion system. Theincrease of oil or MCT content also increases the droplet size and viscosity ofthe system. However, for high HLB numbers, 13-16.7, emulsions exhibited astable oil droplet size as compared to lower illB numbers between 8-13. Therewas no correlation between stability and illB numbers, but the stability ofnonaqueous emulsion varied with the content of MCT in the emulsion.REFERENCESBECHER, P. 1965. Emulsions - Theory and Practice. 2nd edn. New York: Reinhold.BoYD,]., C. PARKINSON and P. SHERMAN. 1971. Factors affecting emulsion stability and theHLB concept. J Colloid Inteiface Sci. 41: 359.FAlRHURST, D., M.P. ARONSON, M.L. GUM and KD. GoDDARD. 1983. Some comments onnon-ionic surfactant concentration effects in oil-in-water emulsion. Colloids andSuifaces 7: 153.TADROS T.H. 1984. Suifactant. London: Academic Press Inc.160 PertanikaJ. Sci. & Techno!. Vol. 10 o. 2, 2002

Emulsion Properties of Mixed Tween20-Span20 in Non-Aqueous System

http://psasir.upm.edu.my/3743/1/Emulsion_Properties_of_Mixed_Tween20-Span20_in.pdf

Emulsion Properties of Mixed Tween20-Span20 in Non-Aqueous System

Abstract

Similar works

Full text

Available Versions

Universiti Putra Malaysia Institutional Repository