Freeze-fracture electron microscopy results on water-in-oil microemulsion showed that significant polydispersion can be induced by adding water soluble

polymers

Radiman, Shahidan

Universiti Putra Malaysia Institutional Repository

'Pertanika J. Sci. & Techno!. 4(2): 197-200 (1996)ISSN:0128-7680© Penerbit Universiti Pertanian MalaysiaMicroemulsion Polydispersion Due toPolymer SolubilizationShahidan RadirnanNuclear Science DepartmentUniversiti Kebangsaan Malaysia43600 Bangi, Selangor, MalaysiaReceived 10 December 1992ABSTRAKBasil kajian mikroskop elektron sejuk-pecah menunjukkan bahawamikroemulsi air-dalam-minyak mengalami politaburan teraruh denganpenambahan polimer larut-air.ABSTRACTFreeze-fracture electron microscopy results on water-in-oil microemulsionshowed that significant polydispersion can be induced by adding water-soluble polymers.Keywords: electron tnicroscopy, tnicroetnulsion, polyethylene-oxideINTRODUCTIONFreeze-fracture electron microscopy in aerosol-OTIwaterlalkane systemsshows the fairly monodisperse globular structure of the L2 phase 0ahn andStrey 1988). In this note we report two examples of polydispersion inducedby solubilization of polyethylene oxide in an R = [H20]/[aerosol-OT] = 65microemulsion (L2 phase).MATERIALS AND METHODSAerosol-OT (from Sigma Co., USA) was first weighed in 10-ml flasks anddissolved in heptane. Aqueous polyethylene oxide (from Polymer Labs.,Middlesex, England) solution was then added such that the totalconcentration of AOT was 0.1 M and R = 65 was obtained. Two molecularweights were used, namely 12,300 and 105,000. The polymer to waterweight ratio for both was 1/50. This was to ensure that the phase boundariesobtained at room temperature were relatively distant as well as to keep thenumber of polymer molecules small compared to the number of waterdroplets (known from previous studies using small-angle neutron scatter-ing). Several drops of the samples were then transferred on to a dimpledstub, inverted and slammed on to a cold (liquid nitrogen temperature)Shahidan Radimancopper block at a freezing rate of about 8000 K/s. The samples were thentransferred to a Balzers 300 unit (kept at liquid nitrogen temperature and at10-6 Torr) for fracturing and coating. No etching was made. The sampleswere then swirled in a warm acetone solution and the platinum-carbonreplica fished out using a 200-mesh copper grid. Observations were made onthe dried replica using a Philips EM300 transmission electron microscope.RESULTS AND DISCUSSIONPlates 1 and 2 show the relatively polydisperse droplet structure of thepolymer-containing microemulsions. Two populations of the microemulsiondroplets were discernible: an unperturbed monodisperse droplet structureand larger polymer-containing droplets. For the polymer-containingdroplets a simple model of polymer solubilization is hereby proposed:Plate 1. Freeze-fracture electron micrograph of an aerosol-O T water-in-Izeptane microemulsioncontaining polyethylene oxide (mol. wt. = 105,000) at 55,000 magnification. Note the relativelysmall number of large droplets compared to a larger number of smaller droplets in the backgroundLet r be the radius of the polymer-solubilizing droplets and rw that ofthe initially polymer-free droplets. Then,(1)where n is the required number of empty droplets to solubilize the polymerwith microscopic volume vp ' Since the total area covered by the surfactant isroughly conserved, it follows thatr2 = nrw2 (2)198 Pertanika J. Sci. & Techno!. Vo!. 4 No.2, 1996Microemulsion Polydispersion Due to Polymer SolubilizationPlate 2. Freeze-fracture electron micrograph as in Plate 1 but for microemulsion containingpolyethylene oxide of molecular weight = 12,300 at 27,000 magnification. The result is similar toPlate 1.Mass and volume conservation also givenN = Nw and Vp = Nvp (3)where Nand Nw are the total number offilled and empty droplets and Vpisthe total polymer volume in the sample. Also,Vw = Nw .4/37rfw 3When (2-4) are substituted into (1) we obtain4/37rf3 = 4/37rfwf2 + 4/J7TTw f2Vp /Vwwhich simplifies tof = f w (1 + Vp/Vw )(4)(5)If the polymer randomly filled all the droplets this would suggest thatthe radius of the filled droplets would be larger by a small factor of roughly1 + 1/50, which is not borne out by the micrographs seen in Plates 1 and 2.The fact that a bimodal distribution occurs suggests that VplYw » 1/50where V w now refers not to the total volume of water but only to thatcorresponding to the filled droplets. This microscopic segregation ofpolyethylene oxide is probably due to the association of polyethyleneoxide with Aerosol-OT similar to those observed in an independent study ofthis polymer in a sodium dodecyl sulphate solution (Cabane and DuplessixPertanika J. Sci. & Techno\. Vo\. 4 No.2, 1996 199Shahidan Radiman1982). One would also suspect that the droplets would be Poissondistributed if the polymers were randomly distributed (which is not thecase here) among the droplets (Rizzo 1986). Finally, it is expected that thisprocess of droplet aggregation (e.g. by adding more polymers) willeventually lead to emulsification failure due to an average entropic loss.CONCLUSIONWe have shown evidence for a microscopic segregation of polyethyleneoxide in water-in-oil microemulsion which leads to its polydispersion.REFERENCESCABANE, B. and J. DUPLESSIX. 1982. Small-angle neutron scattering studies of SDS-PEG complex. ]. Physique France 43: 1529-1541.JAH , W. and R. STREY. 1988. Microstructure of microemulsions by freeze-fractureelectron microscopy]. Phys. Chern. 92: 2292-2301.RIZZO, V. 1986. Hydrophilic molecules solubilized in water-in-oil microemulsions.]. Colloid and Int. Sci. 110(1): 110-113.200 Pertanika J. Sci. & Techno!. Vo!. 4 No.2, 1996

Microemulsion Polydispersion Due to Polymer Solubilization

http://psasir.upm.edu.my/3251/1/Microemulsion_Polydispersion_Due_to.pdf

Microemulsion Polydispersion Due to Polymer Solubilization

Abstract

Similar works

Full text

Available Versions

Universiti Putra Malaysia Institutional Repository