The compact neutron generator MP320 (Thermo Scientific Inc.) operating on the principle of a
deuterium-tritium reaction was tested before its planned application as the neutron source for the purpose of Fast
Neutron Activation Analysis applications. Plates made from Al, Fe, Sn and Si were irradiated by a 14 MeV
neutron beam and typical neutron induced reactions were identified.Kompaktní neutronový generátor MP320 (Thermo Scientific Inc.) pracující na principu deuterium-tritiové
reakce byl testován před plánovaným využitím jako zdroj neutronů pro neutronovou aktivační analýzu pomocí
rychlých neutronů. Destičky vyrobené z Al, Fe, Sn a Si byly ozářeny svazkem neutronů s energií 14 MeV a byly
identifikovány reakce indukované neutrony typické pro uvedené prvky

Alexa, Petr

Uhlář, Radim

GeoScience Engineering

DSpace at VSB Technical University of Ostrava

1 GeoScience Engineering Volume LIX (2013), No.3 http://gse.vsb.cz p. 1-5, ISSN 1802-5420 THE FIRST TEST OF THE NEW NEUTRON GENERATOR AT THE VŠB - TECHNICAL UNIVERSITY OF OSTRAVA PRVNÍ TEST NOVÉHO NEUTRONOVÉHO GENERÁTORU NA VŠB-TU OSTRAVA Petr ALEXA1, Radim UHLÁŘ2 1 Institute of Physics and Institute of Clean Technologies, VŠB-Technical University of Ostrava, 17. listopadu 15, 708 33 Ostrava, Czech Republic, tel. (+420) 59 732 3100  e-mail petr.alexa@vsb.cz 2 Institute of Physics, VŠB-Technical University of Ostrava, 17. listopadu 15, 708 33 Ostrava, Czech Republic, tel. (+420) 59 732 4481  e-mail radim.uhlar@vsb.cz Abstract The compact neutron generator MP320 (Thermo Scientific Inc.) operating on the principle of a deuterium-tritium reaction was tested before its planned application as the neutron source for the purpose of Fast Neutron Activation Analysis applications. Plates made from Al, Fe, Sn and Si were irradiated by a 14 MeV neutron beam and typical neutron induced reactions were identified. Abstrakt Kompaktní neutronový generátor MP320 (Thermo Scientific Inc.) pracující na principu deuterium-tritiové reakce byl testován před plánovaným využitím jako zdroj neutronů pro neutronovou aktivační analýzu pomocí rychlých neutronů. Destičky vyrobené z Al, Fe, Sn a Si byly ozářeny svazkem neutronů s energií 14 MeV a byly identifikovány reakce indukované neutrony typické pro uvedené prvky. Key words: fast neutron activation analysis, neutron generators, material analysis  1 INTRODUCTION The Fast Neutron Activation Analysis (FNAA) is a non-destructive method to identify about 60 natural elements [1-2]. When a sample is exposed to a 14 MeV neutron beam generated during a deuterium-tritium (D-T) fusion, (n,p), (n,2n), (n,α) and in some cases also (n,) or (n,n’) are the most important neutron reactions for the FNAA [1]. The formed nucleus is radioactive and decays emitting characteristic delayed gamma rays observed in the FNAA. In this work, the D-T neutron generator (NG) MP320 (Thermo Scientific Inc.) [3] was tested by irradiating plates made from Al, Fe, Sn and Si and by identifying delayed -rays. The NG has a cylindrical shape (12 cm in diameter, 57 cm in length), and can produce 108 neutrons/s at maximum in continuous or pulsed regimes. The model MP320 of the D-T NG was selected for its relatively low cost, low power consumption (75 W), mobility (total weight of 12 kg) and its versatility: applications in the FNAA, the carbon detection via neutron induced prompt gamma emission and the investigation of biological effects of fast neutron irradiation.  2 EXPERIMENTAL PROCEDURE During the experiment, the NG was operated in a pulsed mode with the frequency of 10 kHz, the duty factor D = 0.1 (10 %), the acceleration voltage U = 80 kV and the beam current I = 60 A. The neutron yield was calculated from the known voltage U [kV], current I [A] and the duty factor D according to the NG manual [4] from:    n/s1040207060 723 UUIDY  (1) The NG was located inside a 1 m thick aerated concrete (Ytong, a density of 650 kg m-3) shielding in a 0.5 m x 0.75 m cavity (see Fig. 1).  2 GeoScience Engineering Volume LIX (2013), No.3 http://gse.vsb.cz p. 1-5, ISSN 1802-5420  Fig. 1 A schematic drawing of the irradiation facility (NG, Ytong shielding and a sample position).    Fig. 2 Neutron flux distribution in cm-2 s-1 inside the NG and in its immediate vicinity.  3 GeoScience Engineering Volume LIX (2013), No.3 http://gse.vsb.cz p. 1-5, ISSN 1802-5420 Al, Fe, Sn and Si plates with a size of 11  3.8 cm and a thickness of 1 mm (masses: Fe – 32.93 g, Al – 11.77 g, Sn – 30.34 g, Si – 19.32 g)  were irradiated by a neutron beam at a distance r = 10 cm from the NG target centre.  For a rough estimate of the neutron flux Φ through the irradiated sample surface, the isotropic neutron point source was considered and the following simple formula used  12-42scmn 1084rY (2)  The value is in agreement with the result of the MCNP5 (Monte Carlo Neutron-Particle Transport Code, Version 5) calculations of the neutron flux distribution based on the precised NG geometry and a material composition specification (see Fig. 2). The HPGe GC3018 detector (Canberra Inc.) was utilized for the measurement of the neutron induced delayed -ray radioactivity. The detector was cooled in liquid nitrogen and positioned inside a massive shielding (Pb – 100 mm; Cu – 1 mm; Cd – 1 mm). The energy calibration was performed using standard 60Co and 152Eu point sources. The detector was connected through the Canberra DSA 1000 multichannel analyser (MCA) to the personal computer. To manage the detector and the MCA and to analyse -spectrometric data, the Genie 2000 spectroscopy software was selected. The neutron beam irradiation of the samples proceeded twenty minutes. The samples were then placed close to the centre of the detector cap and -rays were recorded for eighty minutes. Tab. 1 presents neutron induced reactions identified in the measured spectrum (Fig. 3). Only the peaks corresponding to the produced radionuclides characterized by the appropriate half-lives were observed. In the gamma spectrum, the annihilation peak at 511 keV produced by the annihilation radiation in the surrounding material or the sample itself is clearly visible. The estimated sensitivity s of the experimental setup (minimum detectable mass) calculated from the known sample masses m, measured photopeak counts P and the background counts under the photopeak B [6],  BPms 3  (3) are shown in Tab. 1.  Tab. 1 The list of the neutron induced reactions clearly identified in the analyzed γ-spectrum.    Neutron induced reaction Cross section (mb) [5] Decay of radionuclide and its half life [5] Gamma energy (keV) Emission probability (%) [5] Sensitivity (g) 27Al(n,p)27Mg 73 27Mg (9.46 min) → 27Al + -e  + e  843.8 71.80 0.38 27Al(n,α)24Na 123 24Na (14.95 h) → 24Mg + -e  + e 1014.5 1368.6 2754.0 28.20 99.99 99.86 0.79 1.3 0.86 56Fe(n,p)56Mn 114 56Mn (2.58 h) → 56Fe + -e  + e  846.8 1810.7 2113.1 100 27.20 14.40 0.33 1.2 2.6 28Si(n,p)28Al 280 28Al (2.24 min) → 28Si + -e  + e 1778.9 100 0.68 29Si(n,p)29Al 137 29Al (6.6 min) → 29Si + -e  + e 1273.4 100 1.6 124Sn(n,2n)123Sn 1515 123Sn (40.1 min) → 123Sb + -e  + e 160.3 85.70 1.4 4 GeoScience Engineering Volume LIX (2013), No.3 http://gse.vsb.cz p. 1-5, ISSN 1802-5420  Fig. 3 Delayed -ray spectrum of the samples.    3 CONCLUSIONS The aim of this work was to analyse the delayed -rays emitted by the neutron exposed metal plates, in order to test the NG D-T generator (MP320, Thermo Scientific Inc.). To confirm the optimal position of the plates at the closest distance from the housing of the NG, MCNP5, computations were performed. The achieved neutron flux activates Al, Fe, Sn and Si plates and the HPGe GC 3018 (Canberra Inc.) detector is efficient to record the delayed -rays emitted by the isotopes produced in the neutron induced reactions. The sensitivity of the experimental setup was found to be in a range of 0.3 - 2.6 g for the neutron yield 107 n/s. The highest sensitivities were observed for the gamma lines 846.8 keV (Fe – 0.33 g) and 843.8 (Al – 0.38 g). The maximum available neutron yield of the NG, 108 n/s, is expected to increase the sensitivity by a factor of 10. The neutron generator MP320 was sponsored by the Municipality of the city of Ostrava. The paper was created at the project Institute of Clean Technologies for Mining and Utilization of Raw Materials for Energy Use, Reg. No. CZ.1.05/2.1.00/03.0082, supported by the Research and Development for Innovations Operational Program financed by the Structural Funds of the European Union and by means of the state budget of the Czech Republic.   REFERENCES [1] IAEA. Neutron Generators for Analytical Purposes In IAEA Radiation Technology Reports No. 1. Vienna: International Atomic Energy Agency, 2012. 145 pp. ISBN 978-92-0-125110-7.  [2] Reijonen J. et al., Nucl. Instrum. and Methods A 522 (2004) 598-602. [3] Chichester D.L., Simpson J.D., Lemchak M., J. Radioanal. Nucl. Chem. 271 (2007) 629-637.  [4] THERMO SCIENTIFIC. MP320 Neutron Generator Operation Manual. Colorado Springs: Thermo Fisher Scientific, 2010. 101 pp. [5] Chadwick, M.B. et al., Nucl. Data Sheets 112 (2011) 2887-2996; www.nndc.bnl.gov [6] Palmer B.M., McInerney J.J., Appl. Radiat. Isot. 45 (1994) 5-9.    5 GeoScience Engineering Volume LIX (2013), No.3 http://gse.vsb.cz p. 1-5, ISSN 1802-5420 RESUMÉ Pro studium struktury látky má neutron velmi užitečnou vlastnost – nulový elektrický náboj. Jaderné reakce vyvolané neutrony nejsou proto ovlivněny coulombovskou bariérou a mohou s větší či menší pravděpodobností probíhat ve velmi širokém intervalu energií neutronů. Během bombardování látky rychlými neutrony (14 MeV) zachytí některá jádra atomů neutron a proběhne jedna z jaderných reakcí (n,p), (n,2n), (n,α) a v některých případech i (n,) nebo (n,n’). Vzniklé jádro je většinou nestabilní a pokud není poločas rozpadu příliš malý, lze studovat zpožděné charakteristické -záření, které umožní určit izotop přítomný v ozařovaném vzorku i jeho množství (neutronová aktivační analýza rychlými neutrony). Množství izotopu ve vzorku je přímo úměrné intenzitě emitovaného -záření.  Za přispění Magistrátu města Ostravy byl zakoupen kompaktní neutronový generátor MP320 (Thermo Scientific Inc.), ve kterém dochází k fúzi deuteria a tritia a uvolňují se neutrony s energií 14 MeV. Maximální emisivita zdroje je 108 neutronů/s. Předložená studie popisuje výsledky prvního testování neutronového generátoru v pulzním režimu s emisivitou 107 neutronů/s. Prezentován je seznam jaderných reakcí, které byly vyvolány bombardováním vzorků (Al, Fe, Sn, Si) neutrony, a příslušné energie emitovaného -záření změřené polovodičovým germaniovým detektorem. Hlavním výsledkem práce je úspěšné ověření funkčnosti generátoru a stanovení minimální detekovatelné hmotnosti pro studované prvky, která se pohybuje v rozmezí 0.3 – 2.6 g, přičemž nejlepších výsledků bylo dosaženo pro železo a hliník. Pro maximální emisivitu NG, 108 n/s, se očekává desetinásobné snížení minimální detekovatelné hmotnosti.    

První test nového neutronového generátoru na VŠB-TU Ostrava

http://dspace.vsb.cz/bitstream/10084/111446/1/34-56-1-PB.pdf

První test nového neutronového generátoru na VŠB-TU Ostrava

Abstract

Similar works

Full text

Available Versions

DSpace at VSB Technical University of Ostrava