Iwata, Hiromitsu

Katayama, Makoto

Kawabata, Hirotaka

Yoshimi, Yuuki

English

Purdue E-Pubs

Purdue UniversityPurdue e-PubsInternational Compressor Engineering Conference School of Mechanical Engineering2006Surface Treatment Technology for Siding Parts ofCompressorsYuuki YoshimiMatsushita Refrigeration CompanyHirotaka KawabataMatsushita Refrigeration CompanyMakoto KatayamaMatsushita Refrigeration CompanyHiromitsu IwataMatsushita Refrigeration CompanyFollow this and additional works at: https://docs.lib.purdue.edu/icecThis document has been made available through Purdue e-Pubs, a service of the Purdue University Libraries. Please contact epubs@purdue.edu foradditional information.Complete proceedings may be acquired in print and on CD-ROM directly from the Ray W. Herrick Laboratories at https://engineering.purdue.edu/Herrick/Events/orderlit.htmlYoshimi, Yuuki; Kawabata, Hirotaka; Katayama, Makoto; and Iwata, Hiromitsu, "Surface Treatment Technology for Siding Parts ofCompressors" (2006). International Compressor Engineering Conference. Paper 1822.https://docs.lib.purdue.edu/icec/1822 C063, Page 1  Surface Treatment Technology for Sliding Parts of Compressors  Y.YOSHIMI, H.KAWABATA, M.KATAYAMA, H.IWATA  Refrigeration Devices Business Unit, Matsushita Refrigeration Company 6-4-3 Tsujido Motomachi, Fujisawa City, Kanagawa 251-8520, JAPAN Phone 81-(0)466-30-1152, Fax 81-(0)466-30-1177, E-mail yoshimi.yuuki@jp.panasonic.com  *Y.YOSHIMI    ABSTRACT  This paper describes a new surface treatment technology for sliding parts of compressors using solid lubricant. Phosphate coating has been commonly used for the surface treatment of sliding parts of compressors. However, the phosphate solution used in the treatment contains nickel which is one of heavy metals. So the process of phosphate coating is unfavorable in the environment and in recycling. This new technology is environmentally friendly because it uses only compressed air and fine particles of molybdenum disulfide that can be reused after the new surface treatment described in this paper. The new technology is superior to the phosphating in terms of sliding characteristics, taking advantage of the self-lubricating characteristic of molybdenum disulfide itself. The new technology has been developed that is effective to improve sliding characteristics and environmentally friendly.  1. INTRODUCTION  Currently, phosphate coating is widely used for the surface treatment of sliding parts of compressors. However, the phosphate solution for this treatment contains nickel, that is unfavorable in the environment. The phosphating has good sliding characteristics because the layer is a porous crystalline that can absorb and hold lubricating oil and has oil-film forming capability during sliding.1) Recently, compressors are required high efficiency so the viscosity of lubricating oil becomes lower. And in this result the metal contacts are occurred more often. Therefore it is difficult to make the best use of features of the phosphating. The other side, solid lubricants are used to improve lubrication in response to increasing the metal contact. However present technologies commonly used for surface treatment with solid lubricants require a binder between the metal surface and the solid lubricants. The binder impedes essential capability of the solid lubricant. In these circumstances we developed a new surface treatment technology that fully utilizes the functions of a solid lubricant and applied the new technology to a compressor.  2. TREATMENT EQUIPMENT  2.1 Equipment This technology is a modification of the fine particle shot peening method, that is, surface modification by blasting fine particles. Bombardment of the surface with high velocity fine particles accelerated by high-pressure air increases the surface temperature of a specimen, instantly melting, and thus modifying its surface. A salient feature of this method is to form high purity solid lubricant layers on the outermost surface of the specimen without using binder.2)  The equipment consists of the separation section, the processing section and the collector, as shown in Figure 1. Molybdenum disulfide fine particles, as shot materials, are blasted against a surface of a specimen with the help of compressed air. The specimen on the table rotates while the blasting nozzle of molybdenum disulfide moves vertically, thus fine particles of molybdenum disulfide are blasted onto all sliding surfaces of the specimen. The blasting pulverizes molybdenum disulfide particles. The particles not to adhesive to the specimen are separated into two portions; ones of more than a certain size are returned to the processing section while the others of smaller size are collected. The collected molybdenum disulfide without any foreign materials keeps its virgin characteristics and can be used in other applications.3)   International Compressor Engineering Conference at Purdue, July 17-20, 2006   C063, Page 2    BlastNozzleSeparationProcessing sectionSeparation sectionSuctionRecoveryCollectorUse for other applicationsParticles of smaller sizeParticles recovery after blastingShot material supplyTurntableParticles of more thana certain size                        Figure 1: Shot material supply process                                                                                 (Equipment construction)   2.2 Specimen Preparation Figure 2 shows fine particles of molybdenum disulfide used as shot materials. The fine particles of molybdenum disulfide are with a purity of no less than 98.5% and an average diameter of 8 ㎛. The molybdenum disulfide fine particles are blasted against a specimen made of sintered iron-based material, under compressed air pressure of 1.0 MPa to prepare an evaluation specimen.    Figure 2: Molybdenum disulfide particles SEM image   International Compressor Engineering Conference at Purdue, July 17-20, 2006   C063, Page 3  3. EXPERIMENTS AND RESULTS  3.1 The Surface Observation The specimen was observed through Scanning Electron Microscope (SEM) and analyzed by Energy Dispersive X-ray spectroscopy for component analyses (EDX). The SEM image in Figure 3 shows that tool marks disappeared and rougher surface is formed on the surface by blasting molybdenum disulfide fine particles. It was found that the surface consists of Mo, S and Fe from the EDX analysis as shown in Figure 4. These findings show clearly that the specimen surface after blasting is covered with molybdenum disulfide layers.   Tool mark               No-coating                                                          MoS2-shot coating  Figure 3: SEM image of the specimen surface observed      E0 (KV)FeSMoFeFe2.00 4.00 6.00 8.00 10.00 12.00 14.00Intensity (CPS)Intensity (CPS)                   Figure 4: Component analysis result by EDX     International Compressor Engineering Conference at Purdue, July 17-20, 2006   C063, Page 4  3.2 The Section Observation Cross section of the specimen sliding surface was observed through Transmission Electron Microscope (TEM) and analyzed by X-Ray Diffraction (XRD). Figure 5 and 6 show that molybdenum disulfide layers of 0.1 - 1 ㎛ thickness are formed on the surface of the specimen. The molybdenum disulfide layers are parallel to the substrate as shown in Figure 5 (b). As shown in Figure 6, the XRD shows the presence of (002), (004), (006) and (008) planes, indicating the layered structure specific to molybdenum disulfide, which is important for lubrication. In addition, molybdenum carbide (MoC), an intermetallic compound, is found in the molybdenum disulfide layers. The intermetallic compound is formed under the conditions that temperature rises at least several hundred degrees in the presence of carbon in the iron-based sintered material and molybdenum in the molybdenum disulfide fine particles used as shot materials. It is highly probable that a portion of the substrate melted and combined with molybdenum disulfide.   X Iron alloy : Fe   Intermetallic compounds : MoCMolybdenum disulfide : MoS2 Surface                (a) Cross section of the specimen sliding surface   10nm   (b) The molybdenum disulfide layers (Closeup TEM image of (X))  Figure 5: Cross section TEM image of the specimen sliding surface       International Compressor Engineering Conference at Purdue, July 17-20, 2006   C063, Page 5   x10^3501001502θ(deg)MoS2（002）MoS2（004）MoS2（006）MoS2（008）Intensity (CPS)Intensity (CPS)050010001500200025003000MoS2（002）MoS2（004）MoS2（006）MoS2（008）FeFeFeMoCMoC MoCMoCMoC2θ（deg）Intensity (CPS)Intensity (CPS)              (a) Surface with MoS2-shot coating                      (b) MoS2 particles used for the shot process  Figure 6: X-ray diffraction measurement result   3.3 Sliding Characteristic Ring on disk tests were performed using a wear tester, shown in Figure 7, to compare the sliding characteristics between phosphating and molybdenum disulfide layers by the new technology. Friction coefficient and wear resistance were evaluated. Table 1 shows ring on disk test conditions. In general, sliding conditions between a piston and a cylinder of a reciprocating compressor changes among fluid lubrication, mixed lubrication and boundary lubrication by crank angle, lubricating oil viscosity, pressure condition and surface roughness. Figure 8 shows that the friction coefficient of the phosphating specimen decreases with the increasing bearing constant in the range of 10 or less of the constant, and then it increases. This means this ring on disk tests are in the boundary range of mixed lubrication conditions. It was found that the specimens treated by the new technology described in this paper have friction coefficients lower than those of the phosphating specimens in all experimental conditions. The effect of the new technology is high, in particular, in the bearing constant range of 0.1 to 1, that is, in the boundary lubrication condition. As described in the preceding section, we think this effect depends heavily on the presence of the specific structure of molybdenum disulfide that is important for lubrication. Figure 9 shows that the wear depth of the specimens treated by the new technology is 1/3 that of the phosphating specimens, indicating the superiority of the new technology in terms of wear resistance. We think there are two things contributing to the superiority, that is, the effect of molybdenum disulfide as a solid lubricant as mentioned in the discussion of the friction coefficient, and strong adhesion of molybdenum disulfide to the substrate through the formation of the intermetallic compound, as mentioned in the preceding section.   OilRotationDiskRingLoadPressure vesselRef. Table 1: Test conditions   Friction coefficient test Wear test Load 10～1800 N 100 N Rotation Speed 0.5～1.0 m/s 1.0 m/s Refrigerant Pressure 0.4 MPa (R134a) Oil Temperature 60℃ Viscosity Grade VG8～VG22 VG8              International Compressor Engineering Conference at Purdue, July 17-20, 2006  Figure 7: Ring on disk test image  C063, Page 6  00.050.100.1 1 10 100Bearing constant［－］Friction Coefficient［－］MoS2PhosphatingFriction Coefficient［－］Sliding Distance ［m］1.51.00.50.0200000 400000 600000MoS2PhosphatingWear Depth ［μm］Wear Depth ［μm］                   Figure 8: Friction coefficient                                                  Figure 9: Wear depth   Next, reliability tests were performed to confirm the effect of the treatment on the piston assembled into an actual reciprocating compressor for hydrocarbon refrigerant used mainly in the market. Table 2 shows reliability test conditions. As shown in Figure 10, the test results by compressor also show that the wear depth of the piston treated by the new technology described in this paper is 1/3 that of the phosphate coating piston. In the performance evaluation, it was found that coefficient of performance (C.O.P.) of the piston treated by the new technology is improved by about 0.01 (W/W) compared to that of the phosphating piston. Thus the improvement of sliding characteristics using the new technology is confirmed with an actual compressor.  Table 2: Reliability test condition  Cylinder volume 10cc Refrigeration R600a Oil Viscosity grade : VG10 Discharge pressure 0.70MPa Suction pressure 0.06MPa   01Time [Ｈｒ]Wear depth ration [-](MoS2/Phosphating)0 1000 2000 3000 4000 5000Wear depth ration [-](MoS2/Phosphating)               Figure 10: Reliability test result  International Compressor Engineering Conference at Purdue, July 17-20, 2006   C063, Page 7   International Compressor Engineering Conference at Purdue, July 17-20, 2006  4. DISCUSSION  The crystalline structure of molybdenum disulfide sufficiently explains why the new technology is better than the phosphate coating in terms of wear resistance and friction coefficient, resulted in better efficiency of the compressor. Molybdenum disulfide is a hexagonal layer compound made from one molybdenum atom and two sulfur atoms, with molybdenum atoms positioned diagonally below the sulfur atoms.4) The chemical bond between Mo and S in the layer is a covalent bond, with very high bonding energy and a bond length of about 1.5 A. While the interlayer bond between S - S separated about 3 A is formed only by Van der Waals force, which is far weaker than the force of the covalent bond. Molybdenum disulfide layers are strong against force perpendicular to the layers because of the covalent bond in the layers, while the layers slide easily in directions parallel to the layers when a force is applied in that direction. This is because the Van der Waals force in the layers is weak. TEM observation confirmed that the molybdenum disulfide layers prepared by the new technology are parallel to the surface of the specimen. This is a reason why a better and stable friction coefficient is obtained. From these findings, we think the improved friction coefficient and wear resistance of the specimens treated by the new technology are brought about heavily by the crystalline and layered structure of molybdenum disulfide, which is not affected by the viscosity of lubricating oil. Another reason why the characteristics of molybdenum disulfide are fully utilized is the development of the new molybdenum disulfide blasting process, which enables the formation of high purity, more than 98 %, molybdenum disulfide layers without employing a binder. Molybdenum disulfide particles blasted against a specimen made of Fe-C alloy increases the surface temperature of the specimen, melting the surface, diffusing thermally into the melted Fe-C alloy, the basic material of the specimen, and forming intermetallic compound of Mo and C, probably through mutual thermal diffusion of the basic material and molybdenum disulfide. The intermetallic compound thus formed acts as an agent to bond Fe-C alloy to the molybdenum disulfide layers. The presence of the intermetallic compound helps realize peel strength of molybdenum disulfide layers that is higher than the strength in the absence of the compound. The new surface treatment technology described in this paper improves the performance of compressors, utilizing fully the self-lubricating characteristics of molybdenum disulfide  5. CONCLUSIONS  The following results were obtained in this research. ・ Friction coefficient can be decreased. ・ Wear resistance can be improved. ・ Pulverized molybdenum disulfide, the only chemical substance discharged in the process, can be 100% recycled.   ACKNOWLEDGEMENT  Our heartfelt thanks go to Messrs Kumagaya and Ishiwata of Fuji Manufacturing Co., Ltd. for their help and support extended to us from the beginning of this research.   REFERENCES  1) Saishin Hyoumen Shori Gijutsu Souran Hensyuu Iinkai, Sangyou service centre Co., Lts., 1987, New engineering review of coating, p.142  2) Yoshiteru Yasuda, Contribution of Fine Particle Peening, the New Surface Modification Technology, to Automotive Parts, Journal of Japanese Society of Tribologists, vol. 47, 12 (2002), p. 897. 3) Hidemi Ogihara, Modification of Piston Sliding Surface for Internal Combustion Engine by Fine Particle Peening of Solid Lubricant, Journal of Japanese Society of Tribologists, vol. 47, 12 (2002), p.895. 4) Masahisa Matsunaga, Yuuko Tsuya, SAIWAI SHOBO, KOTAI JUNKATSU HAND BOOK, p.84-94 

Surface Treatment Technology for Siding Parts of Compressors

https://docs.lib.purdue.edu/cgi/viewcontent.cgi?article=2821&amp;context=icec

Surface Treatment Technology for Siding Parts of Compressors

Abstract

Similar works

Full text

Available Versions

Purdue E-Pubs