Drabaek, I.

Gustafsson, V.

Hansen, P. E.

Pedersen, P. B.

Schmidt, A.

English

Purdue E-Pubs

Purdue UniversityPurdue e-PubsInternational Refrigeration and Air ConditioningConference School of Mechanical Engineering1994Total Environmental Impact of a Small HermeticCompressorP. E. HansenDanfoss Compressors GmbHV. GustafssonDanfoss Compressors GmbHI. Drabaekde-TeknikA. Schmidtde-TeknikP. B. Pedersende-TeknikFollow this and additional works at: http://docs.lib.purdue.edu/iraccThis document has been made available through Purdue e-Pubs, a service of the Purdue University Libraries. Please contact epubs@purdue.edu foradditional information.Complete proceedings may be acquired in print and on CD-ROM directly from the Ray W. Herrick Laboratories at https://engineering.purdue.edu/Herrick/Events/orderlit.htmlHansen, P. E.; Gustafsson, V.; Drabaek, I.; Schmidt, A.; and Pedersen, P. B., "Total Environmental Impact of a Small HermeticCompressor" (1994). International Refrigeration and Air Conditioning Conference. Paper 245.http://docs.lib.purdue.edu/iracc/245Total Environmental Impact of a Small Hermetic Compressor By Poul Erik Hansen, Vibeke Gustafsson Danfoss Compressors GmbH. P.O. Box 1443. D-24939 Flensburg. Germany. Tlf int. + 49464941·109, Fax Int. + 494614941-629 lver Drabek, Anders Schmidt, Preben Buhl Pedersen dk-Teknik, Gladsaxe Moellevej 15, OK 2860 S"borg, Denmark ABSTRACT The relative energy consumption caused by the introduction of the alternative refrigerants has been seen as very important while replacing the CFC's. In the framework of the TEWI concept the influence of alternative refrigerants on the global warming is calculated, taking into account the direct and indirect effect. This paper extends these analyses as it includes the influence of a hermetic compressor in its total lifetime from the production of raw materials to the disposal of the compressor. Further an analysis of the emission of S02 and NOx is given and the amount of waste is estimated. Finally the analysis is used on an energy optimised compressor for the European market. In order to increase the energy efficiency the compressor producers are normally forced to use more materials, e.g. copper wire. It is demonstrated that the energy consumption due to the use of more materials is tenfold regained by the reduction in energy consumption in the lifetime of the compressor. INTRODUCTION Life cycle analysis (LCA) can be defined as an inventory of the environmental impacts of a product from the production of raw materials to the final disposal of the used product. LCA is being used for an increasing number of purposes. Most applications have so far been comparisons between different products serving the same purpose. Lately LCA has been used while product development to include the knowledge of potential environmental impacts of products. The analysis in this paper will provide a comprehensive view of the environmental impacts from a typical compressor (TLSF) in its life cycle.Furthermore a comparison of the environmental impacts of a standard compressor (TLSF) with the corresponding energy optimised compressor (TLESSF) is presented. The compressors used in this analysis are hermetic reciprocating compressors with stroke volumes of 5 cm3 used for domestic refrigeration with the refrigerant R134a. At the standard rating point of 25°C/55°C/32°C the TLSF has a COP of 0,82, the TLESSF a COP of 0,96. METHODOLOGY. The present paper excludes the evaluation of the environmental impacts. Some choices have had to be made, e.g. the analysed geographical area. These ·choices, as well as other limitations in the study will be clarified in the following paragraphs. Key parameters of the analysis will be presented, but some results that may be of relevance in a complete analysis or assessment of the life cycle have been omitted. The analyses include the following phases of the life cycle (figure 1 ): * .. .. * Production of raw materials Production of components Production of the compressor Assembly and sale 177 * * * Use of the compressor Scrapping Recovery of raw materials (copper) The functional yott Defining a functional untt is very important in a LCA because tt is the basis for both analysis and comparisons. In the present study the functional unit is: Use of a compressor in a household refrigeration unit in an assumed unit lifetime of the unit of 12 years. Ute cycle phases and data guality The inventory focuses on the conditions found in Germany and gives a general view of the environmental impacts of a compressor that is produced, used and disposed of in Germany under conditions found in 1992/93. The data quality is not equal for all phases in the LCA. For the phase "Production of raw material" old data have been used in most cases. The age of the data is of minor importance as new technologies have not emerged during the recent years. The impact from production of some of the materials (e. g. the plastics) have been estimated consetvatively. As these materials only form a minor part of the compressor, the error introduced with this is very small. The phase "external production of components" was analysed by making analogies to the production at Danfoss · Compressors. This is because only few data from suppliers to Danfoss Compressors were available. "Production at Danfoss Compressors" was analysed using a black box approach. In all calculations the annual impact from the production is equally distributed on all compressors, desptte special condttions. The environmental impact from operation and maintenance of the production faciltties was included in this phase. Whether this is the case for the other phases are not clear. "Assembly and sale" was analysed using data from only one producer of refrigerators. It was assumed that the best available technology is used. The compressor is used in a small refrigerator with a net volume of 144 lttres. "Use of the compressor" was analysed using the following energy mixture: 58.2% Coal 27.8% Nuclear power 7.5% Natural gas 3.1% Hydro electrictty 2.0% Oil 1.5% Other The average efficiency in electrictty production was assumed to be 37.4%, equal to the German average for conventional power production. When a general knowledge was present emissions, i.e. S02, NOx and C02, were included in the analysis. It was assumed that no changes in the energy mixture will occur during the use phase. The energy consumption was calculated according to a model developed at The Institute of Physics, Technical University Of Denmark. The calculations were corrected for the heat production from the compressor and the waste from the energy production was calculated and included. In the "Scrapping" phase it was assumed that the compressors from Danfoss Compressors are treated like average compressors, i.e. 40% are recycled in "informal circutts• and 60% are sold to a copper mill for recovery of the copper. Scrapping and disposal of the refrigerator (inclusive the compressor) was assumed to take place at a modem German scrapping plant. A compressor produced in 1993 will use R134a, but a compressor that is being scrapped in 1993 was produced 12 years ago and has used R12 as refrigerant. Since tt is very difficult to estimate the development of scrapping technology, it was assumed that best current technology will be used. In the analysis of the "Copper Mill" it was assumed that the copper is recovered while all other residues are disposed of as waste, e. g. fillings for roads and ditches. 178 The impact from transportation is less than 0,1 percent of the impact in the use phase and is only estimated. An Material flow in the life cycle of compressors 1. Production of raw materials 2. External production of components 7. ~~~~~~~~~~6. Scrapping Copper mill Figure 1. The material flow in the different phases of a life cycle of a compressor. even smaller contribution comes from the packaging materials, mainly wood. RESULTS 5. Use of CO!llpressors Production 61 281 24,9 80,5 44 x x x of raw materials External 59, 7 6, 6 15, 5 13 ? ? ? production Production at Danfoss Compressors Assembly and sale 93,9 0,1 10,4 24,3 20,5 X 0,01 48,9 0,96 - 1,33 Use 29800 1100 1600 3000 X X 15,7 Scrapping -0,4 1 1,6 7,6 In the pnase Assembly and sale tne rerngerant ts F 134a used tn the TL5F; In "Scrapptng the refngerant ts R12 111 hicflts us 3d tn older compressors. Table 1. Key parameters in the life cycle of a compressor (TLSF). 179 In table 1 and figure 2 the impacts in the life cycle of a compressor is presented. It is obvious that the use phase is the most important with respect to both consumption of primary energy and emissions. However, it should also be noted that heavy metals and polycyclic aromatic hydrocarbons (PAH) are present in several phases of the life cycle. The emissions of these compounds have not been quantified. The materials produced in the phase "Production of raw materials" enter the life cycle in three subsequent phases. The final compressor weighs 7,8 kg. COMPARISON BETWEEN THE TWO COMPRESSORS The difference between the two compressors is found in the phases "Production of raw materials" and "Use". The difference in "Production of raw materials" is shown for some key parameters in figure 3. The difference in the consumption of raw materials is mainly caused by a use of more copper (approx. 137 grams) in the TLESSF. The copper content in an ore is less than 1%, so the use of additional 137 grams of copper will accordingly increase the consumption of raw materials with 14 kilos. The use of iron in the TLESSF is less than in the TLSF, but totally the TLESSF consumes more raw material than the TLSF, although the final compressor weighs less. The bigger consumption of energy in the production of raw materials for the TLESSF is also caused by the increased amount of copper. The difference between the two compressors Key parameters in different phases (Logaritmic scale) 1E5 1E4 1E3 1E2 1E1 1EO L..==~~'-..!!!!!!!!!L.;!!!!!!!!~ Energy con-EmissionEmission Emission Wa!l.e sumption of C02 of S02 of NOx (kg) (MJ) (kg) (g) (g) Figure 2. Key parameters In different phases of the life cycle of a compressor (TLSF). in the use phase is demonstrated in figure 4. As can be seen, the TLESSF consumes about 9% less primary Comparison between TL5F and TLES5F Production of raw materials TU 110 C50 30 20 Raw materials Energy (kg) (MJx 10) Water (lllreS) Weste (kg) Figure 3. Comparison of ksy parameters in production of raw materials for two compressors. Comparison between TL&F and TLES6F Use phase • 3.11 3 2.11 2 1.li Energy E;m~ssiln <1 EmiSSicln fl Emission Ill (GJ X 10) C02 (IDn) S02 (lig) NOX (kg) Figure 4. COmparison of kay parameters In the use phase of two compressors. 180 absolute consumption of energy, this decrease becomes more significant as the energy consumption in the use phase is 99% of the total consumption in the whole life cycle. The decrease is thus 10 times the total con· sumption in all other phases. In all other phases only minor differences between the two compressors can be found. It should be noted that the extra copper used in the TLESSF will be partly (60%) recovered in the scrapping phase. CONCLUSIONS The analysis shows that the major part of the energy consumption of a compressor takes place during the uuse• phase. For a typical compressor the consumption in the use phase is about 99% of the total energy consumption. Improvement in terms of a reduced environmental impact should therefore concentrate on this phase. This is similar to the conclusions from the TEWI analysis of refrigerants (3). The direct contribution on global warming from a refrigerant is only a minor fraction of the indirect contribution, i.e. the energy consumption in the refrigerator. A comparison between a standard compressor and an optimised compressor shows that a reduction of 9% in the energy consumption has been accomplished, equal to 10 times the total consumption in all other phases. The "investment" of more materials e.g. copper, pays well off on the total energy balance. REFERENCES 1. National Energy Data Profile- Federal Republic of Germany. World Energy Counsel, 15th W.E.C.Congress 1992. German Member Committee. 2. Anders Schmidt et at., "The Danish Materials Technology Programme. The frame programme for integrated environmental and occupational assessment. u Methodology appendix., Feb. 1992. 3. AFEAS, US. Department of Energy, uenergy and Global warming Impacts of CFC Alternative Technologies", DEC 1991. 181 

Total Environmental Impact of a Small Hermetic Compressor

https://docs.lib.purdue.edu/cgi/viewcontent.cgi?article=1244&amp;context=iracc

Total Environmental Impact of a Small Hermetic Compressor

Abstract

Similar works

Full text

Available Versions

Purdue E-Pubs