The recovery of glycerine from spent soap lye has been done using soap lye samples obtained from the cold process

of soap production using palm kernel oil (PKO) and palm oil (PO). The overall weight of glycerine recovered per

200g of oil used, was 9.8g (4.9%) and 9.4g (4.7%) from PKO and PO soap lye respectively. Thus an average of

56.3% and an average of 53.9% of the glycerine in spent soap lye were recovered from PKO and PO soap lye

respectively. Higher quantity of brine (200g at 8% concentration) was needed to recover 9.8g of glycerine from

PKO soap lye than that (50g at 12% concentration) required to recover 9.4g of glycerine from PO soap lye. The

weight of glycerine obtained from palm kernel soap lye increased steadily going through some maxima at various

brine concentrations before they began to drop. At 8% concentration, the maximum value of glycerine obtained was

9.8g, 7.9g at 10% concentration, 8g at 12 and 15% concentrations respectively. While the weight of glycerine

recovered from palm oil soap lye increased minimally at all concentrations. At 8% concentration the maximum

value of glycerine recovered was 8.2g, 9g at 10% concentration, 9.4g at 12% concentration and 9.1g at 15%

concentration

Adeeyo, O.A.

Anawe, Paul Apeye Lucky

Efeovbokhan, Vincent Enon

Obafunso, Bisola Aderonke

Covenant University Repository

International Journal of Engineering & Technology IJET-IJENS Vol: 12 No: 02                     11                                                                                           122402-7171 IJET-IJENS @ April 2012 IJENS                                                                                        I J E N S RECOVERY OF GLYCERINE FROM SPENT PALM KERNEL SOAP AND PALM OIL SOAP LYE  Efeovbokhan, Vincent Enon.1, Anawe, Paul Apeye Lucky2, Adeeyo, Opeyemi3  and Obafunso, Bisola Aderonke4 1, 3, 4Chemical Engineering Department, Covenant University, O a, Nigeria. 2Petroleum Engineering Department, Covenant University, Ota, Nigeria ABSTRACT: The recovery of glycerine from spent soap lye has been done using soap lye samples obtained from the cold process of soap production using palm kernel oil (PKO) and palm oil (PO). The overall weight of glycerine recovered per 200g of oil used, was 9.8g (4.9%) and 9.4g (4.7%) from PKO and PO soap lye respectively. Thus an average of 56.3% and an average of 53.9% of the glycerine in spent soap lye were recovered from PKO and PO soap lye respectively. Higher quantity of brine (200g at 8% concentration) was needed to recover 9.8g of glycerine from PKO soap lye than that (50g at 12% concentration) requi ed to recover 9.4g of glycerine from PO soap lye. The weight of glycerine obtained from palm kernel soap lye increased steadily going through some maxima at various brine concentrations before they began to drop. At 8% concentration, the maximum value of glycerine obtained was 9.8g, 7.9g at 10% concentration, 8g at 12 and 15% concentrations respectively. While the weight of glycerine recovered from palm oil soap lye increased minimally t all concentrations. At 8% concentration the maxi um value of glycerine recovered was 8.2g, 9g at 10% concentration, 9.4g at 12% concentration and 9.1g at 15% concentration.  KEY WORDS: Glycerine, Recovery, Spent soap lye, soap quality.    INTRODUCTION: Glycerol (propan-1, 2, 3-triol) is an important by-product of soap manufacture. It is found  dissolved in the soap lye and as impurity in the crude soap when fats and oils are saponified by causti  soda. [1,2,3]  The process of soap manufacture from fats and oil usually yields glycerol to about 10% of the value of the soap formed and because of its many uses, its recovery is vital to the manufacturing cost analysis for any soap making venture. Unfortunately many small scale and medium scale soap producers usually discard the lye as a waste.  In Nigeria, large tonnage of soap is produced annually from vegetable oils (principally from palm kernel and/or palm oils) by cottage and medium industries. In most cases, the soap as it is being used for laundry purposes is in its crude state because of the high level of glycerin and other impurities still embedded in it. The glycerin is eventually wasted or lost along with the soap usage because they are never salted to rcover the glycerine. Hence, it becomes very advantageous economically to recover at least some of the glycerin from such soap during soap production. The glycerine, when further processed, can be an added source of income to the soap manufacturer because of its wide range of both industrial and domestic applicability. Soap is a cleansing agent made from the interaction of fats and oils with alkali. In chemistry, soap is a salt of a fatty acid. [1] Soap is mainly used for washing and cleaning, but soaps are also important components of lubricants. Soaps for cleansing are obtained by treating vegetable or animal oils and fats with a strongly alkaline solution. The alkaline solution, often lye, promotes what is known as saponification. In saponification, fats are broken down (hydrolyzed) yielding crude soap, i.e. impure salts of fatty acids and glycerol.  Fats and oils for soap are compounds of glycerin and  fatty acid. When oils are mixed with an alkali, they form glycerin and the sodium salt of the fatty acid. The fatty acids required for soap making are supplied by tallow, grease, fish oils, and vegetable oils. [4]         Lye, also known as caustic soda, is a basic ingredient n soap making. [1] It combines with fatty acid derivatives to produce soap. This chemical process is known as saponification. Traditionally, saponification involves hydrolysis of esters under basic conditions to form an alcohol and the salt of a carboxylic acid (carboxylates). Saponifiable substances are those that can be converted into soap. [5] International Journal of Engineering & Technology IJET-IJENS Vol: 12 No: 02                     12                                                                                           122402-7171 IJET-IJENS @ April 2012 IJENS                                                                                        I J E N S Soap comprises of sodium or potassium salts of various fatty acids but chiefly of oleic, stearic, palmitic, lauric and myristic acids and is obtained by reacting common oils or fats with a strong alkaline solution (the base, popularly referred to as lye) in a process known as saponification. The fats are hydrolyzed by the base, yielding alkali salts of fatty acids (crude soap) and glycerol5. Currently, sodium carbonate or sodium hydroxide is used to neutralize the fatty acid and convert it to the salt Charles, 2003), and its by-product.  In saponification, formation of salt by reaction of the base with a long chain fatty acid yields. [6]  Fat + 3NaOH              Glycerin + 3Soap Splitting of oils and fats by hydrolysis, or under basic conditions (saponification), yields fatty acids, with glycerin (glycerol) as a byproduct. [7] In the process of salt formation between the reaction of the base or alkali and the fat, glycerin- a by-product is formed. Glycerin presence is responsible for the softening of soap and depending on the desired quality of the final product; varying amounts of glycerin may be incorporated. However, excess glycerin is removed an this process otherwise referred to as drying makes the soap hard enough to form a distinct shape. [8, 9] Addition of salt water to dissolve glycerine and precipitate the soap forms the basis of this process. [10, 11, 12]  MATERIALS AND METHODS:  The spent lye sample used in this study was generated from the soap samples prepared at the Chemical Engineering Laboratory, Covenant University, Canaan Land, Ota. The palm kernel oil, sodium chloride and caustic soda were purchased from a local Chemical market at Ojota, Lagos. Brine Solution Preparation: 8% concentration (weight by weight) of brine solution was first prepared by dissolving 80g of sodium chloride in 920 g of distilled water in a one litre plastic container and covered with a lid. Various other concentrations 10, 12 and 15% wt/wt. were similarly prepared and stored.  Soap Preparation and Salting: The cold process was used. Here, 200g of the palm kernel oil whose saponification value had been determined was first weighed into a one-litre glass beaker and gently heated to a temperature of 40oC. 23.6g of caustic soda was then weighed and dissolved in 78g of distilled water in a 500ml plastic container to give about 23.22% caustic solution. This was allowed to cool to a temperature of 40oC. At 40oC the caustic soda solution was then carefully poured into the oil and under continuous stirring until a homogenous soap paste or trace was formed. Salting of the soap samples was done using varied quantities of the 8% brine solution for each batch of soap sample prepared. Salting process was repeated using 10, 12 and 15% brine solutions for other soap batches prepared. The salting process separated the soap two phases; soap (upper phase) and the spent soap lye (lower phase).  The spent soap lye contained the glycerin.  Glycerin Recovery From Spent Soap Lye: The spent soap lye was filtered in order to remove unwanted soap particles. Each filtrate was heated to different t mperature of 60oC in 250ml conical flasks. Acid treatment was followed by adding 0.1M Hydrochloric acid (HCl) drop wisely until the pH range was within 4.0-6.0. The sample was filtered into a conical flask. 0.1M sodium hydroxide was then added with the aid of a pipette to the filtrate in other to raise the pH again to a range of between (8.0-10.0). The sample was then filtered again and poured into a 250ml beaker. This was then kept in an oven for drying at 1500C leaving the crude glycerine and salt. The salt is insoluble in glycerine. The crude glycerine sample was carefully decanted, weighed and stored in a refrigerator to further precipitate the remaining salt (if any) in the sample. The glycerine recovered was weighed again.          International Journal of Engineering & Technology IJET-IJENS Vol: 12 No: 02                     13                                                                                           122402-7171 IJET-IJENS @ April 2012 IJENS                                                                                        I J E N S RESULTS AND DISCUSSION:  Fig.1: Recovery of Glycerine from Soap Lye at Varied Quantities of 8% Brine Concentration at 60oC.   Fig.2: Recovery of Glycerine from Soap Lye at Varied Quantities of 10% Brine Concentration at 60oC.  International Journal of Engineering & Technology IJET-IJENS Vol: 12 No: 02                     14                                                                                           122402-7171 IJET-IJENS @ April 2012 IJENS                                                                                        I J E N S  Fig.3: Recovery of Glycerine from Soap Lye at Varied Quantities of 12% Brine Concentration at 60oC.   Fig.4: Recovery of Glycerine from Soap Lye at Varied Quantities of 15% Brine Concentration at 60oC.  From the graphs 1-4, weights of glycerine recovered from lye obtained from PKO progressively increased until they got to their respective maxima and then begins to drop. The highest value of glycerine recovered was 9.8g at 8% brine concentration using 200g quantity of same for salting. While the weights of glycerine recovered from the lye obtained from PO showed slight decreases at all conditions (see graphs 1-4). The highest value of glycerine recovered was 9.4g at 12% brine concentration using 50g quantity of it for salting. Generally, it was observed that the higher t  percentage brine concentration, the higher the value of glycerine recovered. The overall effect of percentage brine concentration on glycerine recovery was more International Journal of Engineering & Technology IJET-IJENS Vol: 12 No: 02                     15                                                                                           122402-7171 IJET-IJENS @ April 2012 IJENS                                                                                        I J E N S pronounced than the quantity of brine used. This effect could be seen from the curves of the weight of glycerine recovered moving upward as brine concentrations were increased. Also, the highest yields of glycerine in all of the conditions were obtained at relatively lower amounts of the respective brine concentrations.  It was further noticed that the variation in amount of glycerine recovered from spent soap lye depended very much on the nature of the soap lye and the method of treatm nt. The acid and alkaline treatments of the soap lye in adjusting the pH of the lye helped to reduce the amount of salt originally combined with the soap by precipitation, coagulation and flocculation10.   CONCLUSION The recovery of glycerine from spent soap lye indicates that: * Glycerine can be successfully separated from soap lye irrespective of the source or nature of the fatty acids from which the soap was made. *  The weight of glycerine obtained from the two soap lye depended more on the percentage brine concentration rather than its quantity.  * Higher yields of glycerine were obtained from the two soap lye for all concentrations investigated at lower brine quantities.  * The salt used for salting was at some point in the process recovered. Salt is insoluble in glycerine and hence could be reused. This makes the economy of the process (glycerine recovery) a viable option f r local soap manufacturers as it would be an added source of income to them aside from improving both thetexture and overall quality of the soap obtained.  It is suggested that further work on the recovery of glycerine from spent palm kernel and palm oils soap lye using the hot process of soap manufacture be investigated. This is because local soap manufacturers use either the hot or cold process for soap making. Such investigations will provide the needed platform foreffective comparison of glycerine yields from both processes.      REFERENCES 1.  SRS Engineering Corporation, Biodiesel Technology,       Available from http://www.srsengineering.com [Accessed 7th may, 2011]  2.  McNaught AD, Wilkinson A. (1997) IUPAC. "IUPAC Gold Book - soap" Compendium of Chemical Terminology, 2nd ed. Compiled by Blackwell Scientific Publications, Oxford (1997). ISBN 0-9678550-9-8. doi:10.1351/goldbook.   3. Thorsten Bartels et al. "Lubricants and Lubrication" in Ullmann's Encyclopedia of Industrial Chemistry, 2005, Weinheim. doi:10.1002/14356007.a15_423  4. Mensink, RP; Katan, MB (1992). "Effect of dietary fatty acids on serum lipids and lipoproteins. A meta-analysis of 27 trials.". Arterioscler Thromb 12 (8): 911  5. Soap Basics: Pure, Natural Ingredients for Soap M king. Traditional & Contemporary Materials for your Cosmetic Creations.  23 Southbrook Road Melksham Wiltshire SN12 8DS United Kingdom  www.soapbasics.co.uk [Acessed April, 2011]  6. Reeves J.B, Weihrauch J.L, Consumer and Food Economics Institute (1979). Composition of foods: fats and oils. Agricultural handbook 8-4. Washington, D.C.: U.S. Dept. of Agriculture, Science and Education Administration. p. 4. OCLC 5301713.    7. Ang, C.Y.W, KeShun L, Yao-Wen H, eds. (1999). Asian Foods Asian foods: science & technology Technomic Pub. Co., Apr 5, 1999 - Cooking – p. 40-10   8. Education Administration Washington D.C.. 4. U.S.A. Federal Food, Drug and Cosmetic Act, 21 CFR 101.25 as amended in Federal Register July 19, 1990.  International Journal of Engineering & Technology IJET-IJENS Vol: 12 No: 02                     16                                                                                           122402-7171 IJET-IJENS @ April 2012 IJENS                                                                                        I J E N S  http://www.americanpalmoil.com/publications/16factsPO.pdf 9. Akpan U.G, Jimoh A, Mohammed A.D, (1999) Extraction, characterization and modification of castor seed oil. Leonardo J. Sci., 4, 1-8.  10. Palm oil Wikipedia,   Available from http://www.wikipedia.com  [Accessed April, 2011].  11. Bellis M, "The History of Soaps and Detergents" http://inventors.about.com/library/inventors/blsoap.htm. [Accessed April, 2011].  12. Israel U, Obot I.B, Asuquo J.E, (2008) Recovery of glycerin from spent soap lye  E-Journal of Chemistry http://www.e-journals.net Vol. 5, No.4, pp. 940-945, October 2008 ISSN: 0973-4945; CODEN ECJHAO [Accessed October, 2011]  13. Experience the joys of Soap making. Super Soap Making. What Is Trace? Available at http://www.supersoapmaking.com/what-is-trace.html [Accessed November, 2011].   

Recovery of Glycerine From Spent Palm Kernel Soap and Palm Oil Soap Lye

http://eprints.covenantuniversity.edu.ng/3391/1/ARTICLE%201.pdf

Recovery of Glycerine From Spent Palm Kernel Soap and Palm Oil Soap Lye

Abstract

Similar works

Full text

Available Versions

Covenant University Repository