The shaking table system for geotechnical centrifuge, which can simulate sinusoidal and real seismic waves under a centrifugal force of 50 times earth gravity, is capable of providing significant data for the seismic design of structures. The shaking table can accommodate test specimens up to 250kg under 50G condition, so it can be used to perform various types of ground shaking tests

ECT Team, Purdue

English

Purdue E-Pubs

Purdue University Purdue e-Pubs ECT Fact Sheets Emerging Construction Technologies 1-1-2007 Shaking Table System for Geotechnical Centrifuge Purdue ECT Team Purdue University, ectinfo@ecn.purdue.edu DOI: 10.5703/1288284315775 Follow this and additional works at: https://docs.lib.purdue.edu/ectfs  Part of the Civil Engineering Commons, and the Construction Engineering and Management Commons Recommended Citation ECT Team, Purdue, "Shaking Table System for Geotechnical Centrifuge" (2007). ECT Fact Sheets. Paper 66. http://dx.doi.org/10.5703/1288284315775 This document has been made available through Purdue e-Pubs, a service of the Purdue University Libraries. Please contact epubs@purdue.edu for additional information.      Factsheet ID: CV03013 Page 1 / 3  http://dx.doi.org/10.5703/1288284315775 © Purdue University     SHAKING TABLE SYSTEM FOR GEOTECHNICAL CENTRIFUGE   THE NEED  Because of the increasing constructions of large-scaled and important structures on soft grounds especially in bay area development, it has become very necessary to investigate the seismic ground behavior. One effective method of studying such behavior is to conduct shaking table tests under a centrifugal field using a model specified from the actual structure in accordance with the similarity law, so as to allow economic evaluation of alternative designs, investigation of complex problem areas, and validation of numerical methods with instrumented physical models.   FIGURE 1 SHAKING TABLE SYSTEM   THE TECHNOLOGY  The shaking table system for geotechnical centrifuge, which can simulate sinusoidal and real seismic waves under a centrifugal force of 50 times earth gravity, is capable of providing significant data for the seismic design of structures. The shaking table can accommodate test specimens up to 250kg under 50G condition, so it can be used to perform various types of ground shaking tests. Because the maximum excitation acceleration of the shaking table is 25G (i.e. 500 Gal in full scale prototype), it can simulate the response of ground during large earthquakes. The available frequency range of the system is from 25 to 350Hz (corresponding prototype frequency is 0.5~7Hz), which covers the predominant frequency range of  Civil - Construction Equipment & Methods      Factsheet ID: CV03013 Page 2 / 3  http://dx.doi.org/10.5703/1288284315775 © Purdue University     real earthquakes. The data acquisition system can simultaneously measure 48 channels of signals including acceleration, displacement, pore water pressure and earth pressure, etc.  FIGURE 2 PRINCIPLE OF CENTRIFUGE MODELING TEST   THE BENEFITS  This technology can be applied following fields: 1) Investigation on the dynamic soil-structure(such as bridge foundation, tunnel, etc.) interaction. 2) Simulation of the response of liquefied ground. 3) Verification of liquefaction-resistant construction method. 4) Verification of the seismic stability of soil-structures.  STATUS  Direct application to specific engineering design historically has been reserved for large projects, which justify the time and expense involved. These have included, for example, offshore foundation design in the oil industry; large span bridge pier foundation design; seismic and non-seismic design of embankment dams; and seismic design of bridge foundations and waste disposal facilities. However, the frequency with which it is used by large design-construct firms internationally is increasing, especially in Japan. Together      Factsheet ID: CV03013 Page 3 / 3  http://dx.doi.org/10.5703/1288284315775 © Purdue University     these trends point to its increased use in engineering design of difficult, unusual, or extreme geotechnical engineering design.  BARRIERS  Geotechnical centrifuge modeling is a highly specialized laboratory based technique. As such, it suffers from the traditional obstacles to moving research results into practice. For the engineer-contractor, this means developing an appreciation of the potential advantages derived from smarter geotechnical engineering, and being able to see different scenarios played out before construction; the visual nature of the modeling, enhanced by collection of soil and structural response data, however, makes the investment very attractive. For the researcher, this will require increased sensitivity and understanding of the practical needs of real construction, in terms of economics, response time, and the appropriateness of the end product delivered to the engineer-contractor.  POINTS OF CONTACT  Naoto Ohbo, Kajima Technical Research Institute Tel: +81 (424) 89-7296 Fax: +81 (424) 89-7116, E-mail: ohbo@katri.kajima.co.jp Deborah J. Goodings, UMCP Center for Geotechnical Centrifuge Modeling Tel (301) 405-1960 Fax: (301) 405-2585, E-mail: goodings@eng.umd.edu  REFERENCES  1. Kajima Technical Research Institute 2. Center for Geotechnical Centrifuges Modeling, http://www.cee.umd.edu/centrifuge/ 3. U.S. Army Centrifuge Research Center, http://www.wes.army.mil/centrifuge/index.html  REVIEWERS  Peer reviewed as an emerging construction technology   DISCLAIMER  Purdue University does not endorse this technology or represents that the information presented can be relied upon without further investigation.  PUBLISHER  Emerging Construction Technologies, Division of Construction Engineering and Management, Purdue University, West Lafayette, Indiana  

Shaking Table System for Geotechnical Centrifuge

https://docs.lib.purdue.edu/cgi/viewcontent.cgi?article=1065&amp;context=ectfs

Shaking Table System for Geotechnical Centrifuge

Abstract

Similar works

Full text

Available Versions

Purdue E-Pubs