Bushnell, P.

Khalifa, H. E.

English

Purdue E-Pubs

Purdue UniversityPurdue e-PubsInternational Compressor Engineering Conference School of Mechanical Engineering1998Minimum Viscosity for Bearing Reliability inRotary CompressorsP. BushnellCarrier CorporationH. E. KhalifaCarrier CorporationFollow this and additional works at: https://docs.lib.purdue.edu/icecThis document has been made available through Purdue e-Pubs, a service of the Purdue University Libraries. Please contact epubs@purdue.edu foradditional information.Complete proceedings may be acquired in print and on CD-ROM directly from the Ray W. Herrick Laboratories at https://engineering.purdue.edu/Herrick/Events/orderlit.htmlBushnell, P. and Khalifa, H. E., "Minimum Viscosity for Bearing Reliability in Rotary Compressors" (1998). International CompressorEngineering Conference. Paper 1252.https://docs.lib.purdue.edu/icec/1252Minimum Viscosity for Bearing Reliability in Rotary Compressors Paul Bushnell and H. Ezzat Khalifa Carlyle Compressor Division Carrier Corporation 6500 Chrysler Drive Syracuse, NY 13221 ABSTRACT To ensure bearing reliability, it is traditional for compressor manufacturers to specify a minimum oil sump temperature difference above the saturated discharge temperature in a high-side compressor and suction temperature in a low-side compressor. This minimum oil sump temperature specification is, in essence, a surrogate measure of the minimum viscosity the compressor manufacturer reqtrires to ensure adequate lubricant film thickness under system flooding conditions. The minimum viscosity required to maintain an adequate lubricant film thickness in the bearings depends on the bearing geometry, the load and the speed. Because the load, and to a much lesser extent, the speed vary from point to point over the compressor operating envelope, so v.i.ll the minimum viscosity required to maintain adequate film thickness. This paper describes a method for specifying the minimum safe viscosity over the entire operating envelope of high-side rotary compressors based on film thickness calculations. NOMENCLATURE c Radial clearance Pe Pressure at compression angle B D Bearing diameter Rc Cylinder radius Fb Bearing force Rr Roller radius h Cylinder height s Sommerfeld number k Polytropic compression exponent T Temperature N Shaft frequency, Hz Ve Compression volume at angle B f.l Absolute viscosity Vtv Compression volume at B = o pb Bearing pressure e See Figure 3 Pzmiz Pressure of lubricant mixture e Crank position after IDC Pgref Pressure of refrigerant gas If/ See Figures 2 and 3 Pa Discharge pressure X Mass fraction Ps Suction Pressure INTRODUCTION Compressor development involves reliability testing at various points within the operating envelope. It is typical that maximum load flood-back condition is part of the qualification to represent the maximum bearing load and minimum oil viscosity that will result in the minimum bearing film thickness of any continuous qualification tests. This condition is typical of systems with fixed expansion devices and are subjected to high charge levels, low air flow and high ambient condition. This becomes an experienced based point in the operating envelope, where the bearing life is known based on worst case film thickness condition from qualification. From this standpoint, where the bearing load and oil viscosity can be determined, the bearing load and lubricant mixture properties will be described in a form to specifY the minimum viscosity and minimum oil temperature at other conditions though the operating envelope. For a bearing of a given length-to diameter ratio (LID), the minimum film thickness may be computed as a function of the Sonunerfeld number, s = (D!c/.N.p!P. (1) 275 This includes all the variables from the designer's standpoint and is a dimensionless number. c, D, and N are constant in a given fixed-speed design and the active system variables are p and P. The lubricant viscosity, p, is that inside the bearing gap. For the purposes of this paper, however, we will employ the lubricant viscosity in the oil sump as a surrogate. This in tum is determined based on the temperature and pressure of the refrigerant over the oilMrefrigerant mixture in the compressor sump, assuming mixture equilibrium state conditions. This paper describes s method for establishing minimum acceptable sump viscosity and temperature at all points within the operating envelope of a rotary compressor that successfully meets bearing reliability criteria at maximum load. ROTARY COMPRESSOR BEARING LOADS Dynamic Bearing Load The cross section of the compressor is shown in Figure 1. The rotary compressor is a high side compressor with the lubricant subjected to discharge conditions. The bearings are hydrodynamic journal bearings on the upper and lower sides and eccentric bearings. The magnitude and direction of the dynamic load P e are shown in Figure 2. Figure 3 shows the pertinent geometric details. P 8 may be determined by compressor instrumentation or by computing P e based on gas properties and compressor geometry [1] as given by the following equations: Pe = P,(V ro I Vel and (2) Fb = (Pe- P,).h.(2Rc sin(vr/2)) untilPe = P tb (3a) Fb = (P a - P, ).h. (2Rc sin(lfl/2)) until IDC. (3b) Ve is purely geometry dependent and is given by: (4) The bearing film thickness requires numerical solution to the Reynolds equation where P e is the dynamic load input [2]. The minimum film thiclmess can be computed as a function ofS to allow other similar bearing conditions to be determined. This was done for a typical rotary compressor and is shown in Figure 4. BEARING LOAD AND MIXTURE VISCOSITY Viscosity Requirement In order to prevent bearing wear, a minimum hydrodynamic film thickness larger than the RMS value of the composite surface roughness (A>li must be maintained under all sustained operating conditions [3]. The minimum bearing hydrodynamic film thickness can be estimated for any given sump temperature, suction pressure and discharge pressure from the bearing load (a function of suction and discharge pressure) and the viscosity of the lubricant/refrigerant mixture in the sump (a function of discharge pressure and sump temperature.) If P b is a function of P a and P., then the Sommerfeld number will yield f..lmin as a function of P a and P,. Given the mixture properties, the viscosity p is expressed as a function of P a, Tin a high side compressor where P lnU:s: = P a. The dynamically loaded bearing film thickness can be represented in terms of the integrated average load on the bearing as shown through the operating envelope in Figure 5. A more rigorous analysis has also been carried out with the dynamic film squeezing effect taken into account, but the use of the average load was deemed adequate for the purposes of the present paper Assuming dynamic similarity throughout the operating map of a given rotary compressor, the Sommerfeld number could be employed to provide a reasonable estimate of Jlmin(Pa, Ps). 1 Adsorbed anti-wear films generated by the reaction of the lubricant (and its additives, if any) and the sliding surfaces could offer wear protection even when A<l. 276 Mixture Properties and Temperature Effect Lubricant mixture viscosity is available in terms of any two state properties of the mixture from lubricant manufacturers and other organizations [4]. For example, the temperature and pressure of the compressor sump can be measured to determine the viscosity. The discharge pressure is very close to the sump pressure and the oil temperature can be inferred from measurement of the compressor shell base temperature. The mixture properties may be obtained from a Daniel diagram as shown in Figure 7. It can be seen that as the lubricant/refrigerant mixture temperature approaches the saturation temperature for any given isobar, the viscosity drops precipitously to values approaching those of liquid refrigerant, which is typically several orders of magnitude smaller than that of the pure lubricant. To bring this diagram into perspective for a vapor compressor, by specifYing a minimum temperature at a particular discharge pressure, a minimum viscosity will be maintained. The discharge pressure and lubricant viscosity are the common variables that couple the load and lubricant mixture in the compressor. The bearing load is translated into a viscosity requirements through the Sommerfeld number, (6) The required viscosity at the prevailing refrigerant conditions can only depend on the temperature of the sump. For a given compressor, the minimum allowable sump temperature, Tmm is, therefore, a function of P d and Ps only. The minimum viscosity that must be maintained at any condition through the operating envelope is shown for a typical rotary compressor in Figure 8. CONCLUDING REMARKS From well defined and understood high load conditions, the safe viscosity can be mapped as a function of discharge and suction conditions. From this required viscosity, the mixture properties will allow a minimum sump temperature to be specified. This allows the compressor supplier to provide the potential customer with the fl.oodback guidelines to assure compressor reliability within the complete operating envelope. The complete chart should be taken in its entirety, not only at a single point. That is, under no condition within the complete operating envelope of the system should the compressor be continuously operated with sump viscosities lower than those indicated in the chart. Special attention must be paid to overcharged systems with orifice- or capillary-type expansion devices, because these systems may satisfy the minimum viscosity requirements if tested at light loads but fail them at higher loads. Therefore, a continuous floodback test perfonned on such systems at light loads with clean coils and unobstructed air flow may yield satisfactory results, leading to false security, when the same system tested at higher loads may fail the guidelines (high condensing pressures resulting from high outdoor temperatures, dirty coils or obstructed air flow). REFERENCES [1] Slayton, C. R. et al., Compressor Roller Bearing Dynamic Analysis, Proc. International Compressor Engineering Conference, Purdue University, 1982, pp.419-421. [2] Handbook ofLubrication: Theory and Practice ofTechnology, Vol. 2, CRC Press, Boca Raton, 1983. [3] Ludema, K. C., Friction. Wear and Lubricatio!l, CRC Press, Boca Raton, 1996. [4] :Michels, H. H. et. al., Solubility Modeling ofRefrigerant!Lubricant Mixtures, International CFC and Halon Alternatives Conference, Washington, DC, 1995, pl. 277 N -...J co Figure 1 ...t:l k.. ........ .... ....... .. .. Boorirg Fm:iioo Fare \tS. Oari<Prge :m ... .. '• ~·····"""''"" '• ,,,,,o•'' I /'• ········ .. . ...... :t :ro () 0 2001-.......................... E li 240 0 Dredim L..-- en •..L an c Q) ow F<ltE-·- L.. 100 hl g> L.."O :+ 1al iS--Q) 0 •+ 00 L.. 0 LL 0 fn-ntTTTTh-rro-1, o' ,1, o 1 ,1, 1 o 1 I • 1 1 o 1, o o 1l o 1 1 rl1 11 o I o 1 o o I o ,nf.,n-l•rn+rrrrh-o 1 F I o 'o o I •' 1 ~~- 0 0 al 40 00 00 100 12J 140 100 100 _2l) ZD 240 aD 200 3D 3!> 3«J :RJ Oal< age (<ig"a:B) Figure 2 ' ' I I ' I I I i II I I ' ' ' I ' i"'iii: I I I l'i--I i1 ,...." ' I ' I I I I I I I -1 I ' ' ' ' I .TI I I 1 1 -r I II I I I I I I I I I i i I ]I 279 I I I I I I I ,.... ' i I I I II I I I I I I ' I I I I ! I ' 1\ \' I I I ~ II ' ' I I I I 0 T""" _T""" .,.... d g § o o· d -.::1" V;i Q) ,_ :::1 0> ii tv 00 0 Figure 5 ~ l ~ ~ ~ Figure 7 I b s I ;z ·20 0 Bearing load in ro!ary compressor 40 60 80 Saturated suction pressure (Psla) VISCOSITYfTEMPERATURE CHART 20 40 60 60 Tem,p~rll,ure fC) 100 100 0272 035.2 0 43.3 051.3 059.3 067.3 D75.3 !:SJ 63.4 g 91.4 m99A r;a 107.4 ll!ii115A -123.4 -131.5 - 139.5. 120 - 147.5 120 Figure 6 Minimum Viscosity for Rotary Compressors j' L--::::1 0.2 CJ 02 !!:. C'J 0.3 ~ CJ 0.3 I f'::J OA 0 0.4 a. 0 0.5 Gl i EJ 05 D o.e -~ till 07 0 111111 0.7 nl - 0}1 VJ • o.a. -0.9 14QL _____ ,,1 -0.9 20 40 60 so 100 120 -10 Saturated Suc~on Pressure (Psi a) Figure 8 Minimum Sump Temperature Requirement for Rotary Compressors w ~ j ~ ~ 440 "2 f! 200 ~ U) HO 20 40 60 80 Saturated Suction Pressure (Psi a) 100 l=:J 79 6 CJ871 0944 010H ti:J 108.9 0116.1 D 1234 D 130.7 0137.9 ~ 145.2 111152.5 - 159.7 -167.0 .. 174.2 .. 181.5 120 .. 186.8 

Minimum Viscosity for Bearing Reliability in Rotary Compressors

https://docs.lib.purdue.edu/cgi/viewcontent.cgi?article=2251&amp;context=icec

Minimum Viscosity for Bearing Reliability in Rotary Compressors

Abstract

Similar works

Full text

Available Versions

Purdue E-Pubs