Williams, Carol

English

DigitalCommons@USU

1CLEANING, REPAIRINGAND RECONDITIONINGWOOD FURNITURECarol WilliamsUSU Extension AgentWayne and Piute CountiesAugust 2000 FL-HI-500You may have a piece of furniture that is soiled, slightly scratched and worn, but notdamaged badly enough to require stripping and refinishing. You may own a valuable antiquewhose beauty might be enhanced but whose quality could be greatly diminished if you strippedthe old finish away, or did anything more than dust the piece. You may own a piece of furniturethat really needs some attention but your time or personal situation may not allow you to refinishit just now. What to do—clean it and/or recondition it? Cleaning and reconditioning mayaccomplish the task or will temporarily solve the problem until you can do a more thoroughrefinishing.Some methods for cleaning and reconditioning are:1. Cleaning/washing2. Abrasion3. Over coating4. Reamalgamation5. Padding6. PatchingThey are listed in order of increasing difficulty. Use the method that will require the leastwork to accomplish the desired result.CLEANING AND WASHINGThere is no best way to clean a finish. It depends on the kind of dirt. NOTE: Use a waterwash sparingly—water can loosen old glues.1. Hot Wash: Add to each gallon of hot water:2 tablespoons gum turpentine 4 tablespoons boiled linseed oilThis formula works best if it is hot enough to require that you wear rubber gloves. Wringout a soft clean cloth in the solution and wash the wood. The turpentine and hot water will cleanaway soil, oils, and built up waxes and polishes. The linseed oil will replace oils and actually“finish” worn or bare spots. (Linseed oil has been one of the most used finishes of the past.)2Wipe dry and buff with a clean soft cloth. This may be sufficient. Polish with lemon oil or applya surface wax if desired. This wash works well for furniture, cabinets and wall paneling.Murphy’s oil soap or similar products can also be used to wash wood.2. Ammonia wash. Make a solution of 20 percent household ammonia and 80 percent water.Wring clean rag and wipe furniture. Depending on the type of finish, this method may discolor orcloud the wood finish.3. Mineral spirits wash. Moisten a clean soft cloth with paint thinner (mineral spirits) and rubsoiled wood to dissolve polish, wax, oil and greasy grime.ABRASIONWax build up, finger prints, soil or scratches may require you to use an abrasiontechnique. Good furniture finishes are actually thick enough that you can “wear” away damagethat is on the finish and has not penetrated to the wood. Sometimes the damage is only in the waxor furniture polish that is on top of the finish. A white ring is an example. It may be in the wax orpolish or in the finish. Stains that are dark or black are usually through the finish and into thewood. However, the abrasion of the finish will take a high gloss finish to a satin finish and so theabrasion will need to be over the entire surface of the wood.1. Oil and Abrasive PolishNew motor oil ORParaffin oil ORBoiled linseed oilPumice or rotten stone or whiting (abrasive)0000 steel woolPlace abrasive in a small can or jar. Place oil in a small can or jar. Dip a small pad of0000 steel wool into the oil and then into the abrasive. Polish the furniture in small sections, rubback and forth with the grain. Adjust the pressure to the needs of the job at hand When thedefects have been removed or sufficiently repaired, wipe off the surface. Polish with lemon oil orwax with a quality wax if desired. If the piece of furniture has years of polish and wax built up you may want to wipe it offwith paint thinner applied liberally to a soft clean rag before you begin the abrasion process.2. Turpentine and Linseed Oil1/4 cup gum turpentine3/4 cup boiled linseed oil0000 steel woolPlace turpentine and oil in a glass jar. Cover with a tight lid. Shake well before using.When ready to use, put hot water in a small can or jar. Pour some of the mixture on top. Dip apad of steel wool into the mixture and rub the wood surface back and forth with the grain. Whenthe task is completed, polish with a clean soft rag.3. Toothpaste and Soft Cloth or 0000 Steel WoolFor small or simple white spots, try toothpaste. Put a small amount of toothpaste on aclean cotton cloth or 0000 steel wool. Buff carefully with the grain of the wood. Wipe off with aclean cloth and oil or wax the surface.3OVER COATINGIn some cases the wood may be in good shape but the finish may be worn out and thinwith not enough left to repair by the abrasion technique. Over coating is the technique ofapplying a new finish over old.Begin by cleaning the surface with paint thinner or a weak solution of ammonia and waterto remove soil, polishes and waxes. If the stain is worn, apply new stain. In some cases, a coat ortwo of oil based stain buffed into the wood with 0000 steel wool and wiped with a clean cloth isenough finish.If stain has been applied, let it dry thoroughly. Apply a thin coat of a clear finish. It is bestif you apply the same kind of finish that was used originally, i.e., shellac over shellac or varnishover varnish, etc. The least successful method is any synthetic varnish over shellac. The mostsuccessful is penetrating oil/resins over oil/resin finish.Always test a small amount of finish over a hidden part of the furniture.If a surface finish has been applied (not a penetrating oil finish) when it is thoroughly dry,wipe it with very fine steel wool and apply paste wax.REAMALGAMATIONReamalgamation is a process in which the damaged finish on wood is dissolved with asolvent for the original finish and then reapplied as the finish. If this process is well done it willbe beautiful. It does not destroy the “patina” of the wood that has come with age, care and useand is often prized.First you must determine what the finish is because the correct solvent must be used todissolve the finish. Test solvents in a hidden place. Finishes will dissolve in their own solvent.FINISH SOLVENTShellacIf the furniture was built before 1920and has its original finish, it’sprobably finished with shellac.Denatured alcoholLacquerUsed on commercially madefurniture because it dries so rapidlyLacquer thinnerVarnishNot usually found unless the piecewas custom or handmade orpreviously refinished.Difficult to dissolve. Try lacquerthinner or commercial stripper.Penetrating OilsThis finish will probably never needto be reamalgamated because it is soeasily and effectively over coated.(See previous section.)Lacquer thinner or commercialstripper.4For any method, clean the furniture with paint thinner or turpentine. Beginreamalgamation by dipping steel wool or a brush into the appropriate solvent and applying it tothe wood surface. Get the surface wet as quickly as possible before solvent evaporates. Brushand/or rub and reapply solvent until all defects disappear. Apply more solvent to the finish andsmooth the reamalgamated surface with long light strokes, working with the grain. When thesurface is dry, buff it with 0000 steel wool to remove any rough spots. Apply a good paste wax. Itshould look like new.There are some “amalgamators” on the market which are solvents for most finishes. TheMohawk Company has one called “Amalgamator.” Formsby’s is called “Furniture Refinisher.”There are several other brands available. Polyurethane finishes cannot be reamalgamated.PADDING This method is often used by professionals to repair valuable furniture and is called“French Polishing.” Padding is a technique in which a new finish is applied over an old one usinga tightly rolled pad of soft cotton cloth and “padding lacquer” such as Pad-Lac available inConstantines Wood Workers catalog.Make sure the wood is clean. Prepare the padding cloth by rolling a soft clean piece ofcloth fabric large enough to fit in your hand. Dip the pad into a bowl of padding lacquer andsqueeze it to remove any excess liquid.Stroke the damaged surface with a moistened pad, using small up and down rockingmotion with your hand and wrist. The padding cloth must be kept moving because the solvents in“padding lacquer” dry so quickly that a resting pad will leave impressions of the fabric on thewood. Start padding motions gently to wet the surface and then increase pressure to generate heatthat will help lacquer dry. Continue adding padding lacquer to the cloth and move around theproject until finished. Rub the wood surface with the pad for at least 15 minutes to make surelacquer is dry.The padding finish will be quite glossy. If you desire a dull finish, or one with less shine,rub with 0000 steel wool and apply paste wax.PATCHINGPatching is used to repair large scratches, gouges, burns, etc., in the surface. This methodis often used when there is a surface blemish on an otherwise undamaged finish.1. Shellac-Stick PatchingIf shellac sticks are not available in your local paint or hardware store, they may bepurchased from mail order supply firms. You will want to practice the technique on a wood scrapbefore repairing furniture.Shellac sticks in color of woodAlcohol lamp or some way to heat spatula and shellac stickArtists spatula or grapefruit knife400 grit waterproof abrasive paperParaffin rubbing oil (car oil will do)Heat the spatula and the tip of the shellac stick. Apply the melted shellac to damage areaand smear into place with spatula. If shellac cools too fast, reheat spatula andsmooth shellac.5When damage has been repaired and shellac has cooled, shave off excess with sharp razorblade. Sand with 400 grit paper lubricated with the oil. Touch up the spot with padding lacquer.2. Wax Stick PatchingWax sticks are readily available and come in many colors. (I have even used crayons andthey work well.) Colors can be blended.Spatula or knifeA heating source to melt stick. (There are special refinishers hot patching knivesavailable.) Heat wax and let it drip into damaged area. Leave slight excess rounded on top. Use a hotspatula blade to work into blemish and to make it even with surrounding surface. If necessary,smooth it up with the razor blade.If the repaired area will receive any wear, cover it first with a coat of shellac, whichmakes it possible for other finishes to adhere, and then a coat of varnish or lacquer.COMMON SPOTS, DEFECTS AND POSSIBLE CURES1. White Spots, Rings, and BlushingWhite spots are caused from moisture damaging the polish or wax layer of the finish.Some finishes can turn white just from moisture in the air. (This will not happen in most of aridUtah.) The whiter the area, the deeper into the finish the moisture penetration.Cure: Choose an abrasion cure, one of these will cure most white spots and rings. Applywax or polish with lemon oil.2. Dark Spots and RingsDark spots are more serious than white spots and indicate water has penetrated into thewood. This kind of damage does not happen in a short time. It has probably been caused by aflower pot or something very moist being left on the wood for several days.The damaged area will probably need to be stripped, the stain bleached with oxalic acidand refinished. If the whole piece of furniture does not require refinishing, be sure to protect itvery carefully while you repair the damage. Repair the whole surface where the damage is found(i.e., table top, etc.). If you attempt to repair only the spot you will be left with a larger damagedspot. This can be true of all repair methods. NOTE: If you cannot find oxalic acid at the hardwarestore, try the drug store. It comes in crystals which are dissolved in warm water for use.If oxalic acid doesn’t remove the stain, you may try household bleach, or a two solutionwood bleach found at the hardware store. Two-part wood bleach will take all color from wood,so be very careful. Some sources say oxalic acid is very dangerous, others say it is mild and safe.3. SteamingOn raw wood (stripped or unfinished wood) dents are easily removed by holding a hotiron over a damp cloth which has been placed on the dent. Wool fabric works very well becauseit holds lots of moisture without dripping or running. The steaming fills the wood fibers andcauses them to swell and fill the dent. Steam as long as necessary to fill the hole. The fibers willusually swell a little above the surface. It is very important to let the raised wood dry thoroughlybefore sanding or the entire bruised area may come out. On finished furniture, you may have toremove some of the finish or puncture damaged area with pins to allow the penetration of steam.6Repair finish by over coating, reamalgamation or padding.Scratches and Hairline Cracks1. Small scratches and cracks—try one of the following:a. Rub with a walnut meat.b. Rub with Old English or similar stain filled furniture polish.c. Rub with matching color shoe polish.d. Rub with matching oil base wood stain.e. Paint with matching crayon.f. Paint with matching color felt tipped pen.2. Alligatoring and hairline cracks—usually caused by swelling and shrinking of finish:a. Reamalgamate the finish.b. Repair polyurethane finish by over coating with another varnish.c. Buff in a coat of matching stain using 0000 steel wool.3. Deep scratches, missing wood.a. Use a patching method.Scars, Gouges, Burns1. PatchingIf the damage is caused by burning, scrape all of the burned area away before patching.2. Remove old finish and refinish the wood.Worn and Thin FinishesClean. If the stain is also worn away, restain to match surrounding area, and overcoat witha new finish.Abused, Worn and Scratched1. PaddingTry repairing with padding technique.2. Complete refinishing.Remember to assess the soil, spot or damage and use the simplest and easiest method thatwill accomplish the task.Follow cleaning method with a rub down of good quality lemon oil polish (available inmany brands) or wax.Work safely. Use protective gloves and eye glasses when using any chemical or methodto clean or repair wood. Be sure to work in a well-ventilated area!SOURCES USED FOR CLEANING AND REPAIRING OUTLINE1. Furniture Finishing and Refinishing. Sun Set Books, Lave Publishing Co., Menlo Park,Calif.72. Step by Step Furniture Finishing, Restoring, Painting and Antiquing. Nancy HowellKoehler. Golden Press, New York.3. Is There Life After Housework? Don Aslett. Writers Digest Books, Cincinnati, Ohio.4. Clean Your House and Every Thing In It. Eugenia Chapman and and Jill C. Major,Perigre Putman Publishing, New York.5. More Clean Your House and Everything In It. Eugenia Chapman and Jill C. Major.6. Housecleaning on a “Shoestring.” Marilyn Noyes USU Extension Service. Logan, UT.7. Constantines Wood Workers Catalog, 1-800-253-WOOD.8. Many years of personal experience and teaching by the author.RECIPES FOR CLEANERSFurniture Cleaner/ConditionerIngredients: 1. 1/4 cup gum turpentine2. 3/4 cup boiled linseed oil3. Hot waterMixing: Mix 1 and 2 together in a glass bottle with a tight lid. Store until needed. Shakewell before using. Work in well ventilated room. Pour hot water (3) into an emptytuna fish can. Pour the turpentine and linseed oil mixture (1 and 2) over thesurface of the hot water. Do not stir. Dip cloth or 0000 steel wool into the oilymixture floating on the surface of hot water. Rub on small area of the woodsurface. Avoid excess moisture on places that have been glued. Use toothbrush oncarved areas and grooves. For areas that appear to have a buildup of dirt, dip 0000steel wool into the cleaner and rub lightly with the grain of the wood. Then dipfresh cloth into clear, warm water, wring the cloth out and wipe the surface.Polish or wax. Do not reheat remaining mixture. Discard.Furniture Cleaner/ConditionerIngredients: 1. Paraffin oil or new car oil2. 0000 steel wool3. Pumice or whiting4. Clean soft cloths5. Good quality furniture polish (lemon oil)Directions: Put pumice in a saucer or container. Dip steel wool in oil and then in pumice. Ruband clean a small area of the soiled furniture. Wipe area with soft cloth. Repeatuntil furniture piece is cleaned. Polish the entire piece with lemon oil polish andsoft cloths.Furniture Polish, Oil and WaxIngredients: 1. 1 quart mineral oil2. 2 tablespoons Camauba wax or bees waxMixing: Put 1 and 2 in the top of a double boiler and heat until 2 melts and can be mixedwith 1. Then cool and store in glass or plastic bottles.8        Utah State University Extension is an affirmative action/equal employment opportunity employer andeducational organization. We offer our programs to persons regardless of race, color, national origin, sex,religion, age or disability.        Issued in furtherance of Cooperative Extension work, Acts of May 8 and June 30, 1914, in cooperationwith the U.S. Department of Agriculture, Robert L. Gilliland, Vice-President and Director, CooperativeExtension Service, Utah State University, Logan, Utah. (EP/08-2000/DF)Furniture Polish, Lemon OilIngredients: 1. 1 quart mineral oil2. 1 tablespoon lemon extractMixing: Stir 2 into 1, store in glass or plastic bottle.FURNITURE BEAUTY TREATMENTUse this to clean and restore wood furniture (not paint or shellac). It will disguisescratches, remove dullness, and restore oils.In the top of an old double boiler or in a two-quart can, add:3 tablespoons boiled linseed oil (buy it as such)2 tablespoons turpentine1 quart hot waterPlace over hot water until the moisture is as warm as a gloved hand can stand. For bestresults, provide a means for keeping the solution hot while it is being used.Dip in a soft, clean cloth into the solution. Lift it out and squeeze until it does not drip.Go over an area no larger than about 1 by 2 feet, redipping the cloth in the hot solution,squeezing it until it does not drip, and washing until the area is clean. Follow immediately with aclean, dry, absorbent cloth until all oil is removed. Boiled linseed oil allowed to remain on thewood will become tacky. Continue until the entire piece has been cleaned.The solution not only cleans woods, it also protects the finish. The hot water andturpentine removes the soil and the boiled linseed oil lubricates the wood, thus preventinghairline checks in the finish. It also makes checks already in the wood less noticeable.9

Cleaning, Repairing and Reconditioning Wood Furniture

https://digitalcommons.usu.edu/cgi/viewcontent.cgi?article=1505&context=extension_histall

Cleaning, Repairing and Reconditioning Wood Furniture

Abstract

Similar works

Full text

Available Versions

DigitalCommons@USU