Beach, MA

Morris, KA

Naji, A

Warr, PA

IEEE Transactions on Microwave Theory and Techniques

English

Geometric frequency tuning in planar electromagnetic resonators is common in many applications. It comes, however, at a penalty in the resonance quality, Q0. The literature traces the causes of such penalty often in terms of the shortcomings in the added elements and materials, which were used to achieve the tuning. In this paper, however, it is shown that another underlying source of quality degradation exists at the fundamental geometric level. This source, unlike other added sources of degradation during tuning, will always exist (even before tuning takes place) and will rely on the “modal areas” of the geometric modifications made to host the tuning mechanism. Hence, it forms an upper bound to the performance that can be achieved from a geometically-tuned planar resonator, carries an important insight to resonator design in general, and significantly helps in the understanding of the problem of geometric tuning in particular. We present the electromagnetic theory behind this limit and canonically demonstrate it using practical microwave resonator examples. The theory, finite-element method simulation, and experiment results are presented and good agreement is observed. It is shown that incorporating such understanding into the design process of tunable planar resonators can help optimize their performance against a given set of design requirements. Furthermore, the presented theory provides a useful electromagnetic model as a tool for estimating Q0 for geometrically modified or irregular metal patches and planar resonators in general, to assist analysis, and design at any wavelength or application. The theory also asserts that, under a given mode, a planar resonator will always have its maximum Q0 before introducing any internal subtractive geometric modifications (e.g., cuts, apertures, or slits) to its original shape.Geometric frequency tuning in planar electromagnetic resonators is common in many applications. It comes, however, at a penalty in the resonance quality, Q0. The literature traces the causes of such penalty often in terms of the shortcomings in the added elements and materials, which were used to achieve the tuning. In this paper, however, it is shown that another underlying source of quality degradation exists at the fundamental geometric level. This source, unlike other added sources of degradation during tuning, will always exist (even before tuning takes place) and will rely on the “modal areas” of the geometric modifications made to host the tuning mechanism. Hence, it forms an upper bound to the performance that can be achieved from a geometically-tuned planar resonator, carries an important insight to resonator design in general, and significantly helps in the understanding of the problem of geometric tuning in particular. We present the electromagnetic theory behind this limit and canonically demonstrate it using practical microwave resonator examples. The theory, finite-element method simulation, and experiment results are presented and good agreement is observed. It is shown that incorporating such understanding into the design process of tunable planar resonators can help optimize their performance against a given set of design requirements. Furthermore, the presented theory provides a useful electromagnetic model as a tool for estimating Q0 for geometrically modified or irregular metal patches and planar resonators in general, to assist analysis, and design at any wavelength or application. The theory also asserts that, under a given mode, a planar resonator will always have its maximum Q0 before introducing any internal subtractive geometric modifications (e.g., cuts, apertures, or slits) to its original shape

Explore Bristol Research

[15] B.Carey-Smith,P.A.Warr,M.A.Beach,andT.Nesimoglu,“AMEMSready wide tuning range planar resonator with application to microwave ﬂexible ﬁlters,” in

A software deﬁned radio receiver test-bed,” in

Authorized licensed use limited to: UNIVERSITY OF BATH.

Bandwidth and central frequency control on tunable bandpass ﬁlter by using MEMS cantilevers,”

Beach (A’90) received the Ph.D. degree from the

Carey-Smith received the B.E. degree in electrical and electronic engineering from the University of Canterbury, Christchurch, New Zealand, in 1995, and is currently working toward the Ph.D. degree in electrical engineering at the University of Bristol,

Distributed MEMS transmission lines for tunable ﬁlter applications,”

Low-loss bandpass RF ﬁlter using MEMS capacitance switches to achieve a one-octave tuning range and independently variable bandwidth,”

Mark Beach received his PhD for research addressing the application of Smart Antennas to GPS from the University of Bristol in 1989, where he subsequently joined as a member of academic staff.

Microwave Filters, Impedance-Matching Networks and Coupling Structures.

Miniature distributed ﬁlters for software re-conﬁgurable radio applications,” in

RF and Microwave Coupled-Line Circuits.

RF MEMS-based tunable ﬁlters,”

Tayfun Nesimoglu received the B.Sc. degree in electrical and electronic engineering from the Eastern Mediterranean University, Gazimaˇ gusa,

Tunable lumped-distributed capacitively coupled transmission-line ﬁlter,”

Variable MEMS capacitors implemented into RF ﬁlter systems,”

Warr received the B.Eng. degree in electronics and communications from The University of Bath,

A fundamental limit on the performance of geometrically-tuned planar resonators

Abstract

Similar works

Full text

Available Versions

Explore Bristol Research

Crossref