Fuke, H

Imada, S

Imori, M

Matsumoto, H

Shikaze, Y

Taniguchi, T

CERN Document Server

High Voltage Power Supply Module Operating in Magnetic FieldM. Imori, H. Matsumoto, Y. Shikaze1, H. Fuke2, T. Taniguchi 3, and S. Imada4International Center for Elementary Particle Physics, University of Tokyo7-3-1 Hongo, Bunkyo-ku, Tokyo 113, Japan1Faculty of Science, Kobe UniversityRokko-dai 1-1, Nada-ku, Kobe 657 Japan2Faculty of Science, Department of Physics, University of Tokyo7-3-1 Hongo, Bunkyo-ku, Tokyo 113, Japan3National Laboratory for High Energy Physics (KEK)1-1 Oho, Tsukuba-shi, Ibaraki-ken 305, Japan4NF Corporation6-3-20 Tsunashima Higashi, Kouhoku-ku, Yokohama 223, JapanAbstractThe article describes a high voltage power supply moduleincorporating a ceramic transformer. The high voltage powersupply module incorporates a ceramic transformer whichutilizes piezoelectric effect to generate high voltage. Theceramic transformer is constructed from a ceramic bar anddoes not include any magnetic material. The module can workwithout a loss of efficiency under a magnetic field of 1.5 tesla.The module includes feedback to stabilize the high voltageoutput, supplying from 3000 V to 4000 V with a load of morethan 10 MΩ at efficiency higher than 60 percent. A supplyvoltage of 5 V is high enough to provide the high voltage from3000 V to 4000 V at a load of more than 10 MΩ. The modulewill be soon commercially available from a Japanese company.The module is provided with interface for a Neuron chip, aprogramming device processing a variety of input and outputcapabilities. The chip can also communicate with other Neuronchips over a twisted-pair cable, which allows establishing a highvoltage control network consisting of a number of the moduleswhich are interfaced by the Neuron chips individually. Thefunctions of the module kept under the control of the chip aremanaged through the network. The chip turns on and off themodule and sets the output high voltage. The chip detects theshort circuit of the output high voltage and controls its recovery.The chip also monitors the output current. Thus the modules aremonitored and controlled through the network.I. HIGH VOLTAGE POWER SUPPLY MODULEThe high voltage power supply module includes feedbackto stabilize the high voltage output, supplying from 3000 V to4000 V with a load of more than 10 MΩ at efficiency higherthan 60 percent under a magnetic field of 1.5 tesla [1]-[4]. AJapanese company1, trying to improve the performance andto reduce the size of the module, will soon makes a compacthigh voltage power supply module commercially available.The module incorporates a ceramic transformer. The ceramictransformer takes the place of the conventional magnetictransformer. The ceramic transformer utilizes piezoelectriceffect to generate high voltage. The ceramic transformer is1NF Corporation http://www.nfcorp.co.jpconstructed from a ceramic bar and does not include anymagnetic material. So the transformer is free of leakageof magnetic flux and can be operated efficiently under amagnetic field. The transformer is shaped symmetrically in thelengthwise direction and operated in the longitudinal vibrationmode. The maximum power rating of the ceramic transformeris about 4 W.In a high voltage control network, each module is interfacedby a Neuron chip2. Neuron chips enable the high voltagepower supply modules to network intelligently. Neuron chipshave all the built-in communications and control functions toimplement LonWorks3 nodes. These nodes may the be easilyintegrated into highly-reliable distributed intelligent controlnetworks called LonWorks network. Most functions of themodule is brought under the control of the Neuron chip. Sofunction of the module kept under the control of the Neuronchip is managed through the network. The module is turned onand off through the network. The high voltage is set throughthe network. The output current is also monitored through thenetwork. Short-circuiting the high voltage is detected by theNeuron chip and reported through the network. The Neuronchip is enabled to recover the high voltage from feedbackbreakdown, for example, caused by the short-circuiting.II. FEEDBACKThe high voltage power supply is composed of dividerresistors, an error amplifier, a voltage controlled oscillator(VCO), a driver circuit, the ceramic transformer and aCockcroft-Walton (CW) circuit (Fig. 1). The VCO generatesa driving frequency for a sinusoidal voltage wave whichdrives the ceramic transformer. The VCO supplies the drivingfrequency to the driver circuit where the sinusoidal voltagewave is generated synchronized with the driving frequency.The sinusoidal voltage wave is amplified in voltage by thetransformer and then supplied to a Cockroft-Walton (CW)circuit where the sinusoidal wave is amplified further in voltageand rectified. A high voltage is produced at the output of theCW circuit.2Neuron is a registered trademark of Echelon Corporation.3LonWorks is a registered trademark of Echelon Corporation.Regulator  ESJA98 x6x63nF 100nF200MΩ200KΩOPA234PError Amplifier1nFΩ100K 100nF1KΩ50KΩΩLM385    -1.2 OPA234PΩ0.1nFVoltage-ControlledOscillator    Ceramic TransformerµHx2502SK2796Lx2Driver circuitReference Voltage0V2V~4V JKCLKQQ3KΩ8KΩ5KΩ180pFCockcroft-Walton circuitOutput Capacitance Divider Resistor200Ω200pF200pF200ΩINA155JKCLKQQLTC1440TPS2811P1MAX16141ONOFFCeramic Capacitor74HC73RR30KΩTLC5552SK2796L10K20KFREQ1/2Return of Supply voltage5VDISCRILM385-1.2VREFVREF−500mVSupply voltageFigure 1: Schematic circuit of the high voltage supply module.The voltage is divided by the divider resisters and fed tothe error amplifier to be compared with a reference voltage.The output of the error amplifier is supplied to the VCO whichgenerates the driving frequency. The sinusoidal voltage wavedrives the transformer through the driver circuit. Voltageamplification of the transformer depends on the drivingfrequency. The driving frequency is a function of the outputof the error amplifier. So the amplification is adjusted bycontrolling the driving frequency, which stabilizes the highvoltage. Fig. 2 shows amplitude and phase of the transmissionpath from the output of the error amplifier to the output of theCW circuit.The ceramic transformer includes an internal resonancecircuit. The transformer input voltage is amplified at theoutput, with the input to output voltage ratio being anamplitude ratio that shows a resonance as a function of thedriving frequency. The resonance is shown in Fig. 3, wherethe transformer is loaded with 100kΩ. The range of thedriving frequency is designed to be higher than a resonancefrequency of the ceramic transformer. As shown in Fig. 3,the feedback increases the driving frequency when the outputvoltage is higher than the reference voltage at the input of theerror amplifier. Similarly, the driving frequency decreaseswhen output voltage is lower than the voltage specified by thereference voltage.FREQUENCY [Hz]100m 1 10 100 1k 10k 100kGAIN [dB]-100-50050100PHASE [deg]-180-135-90-4504590135180Figure 2: Amplitude and phase of the transmission path from theoutput of the error amplifier to the output of the CW circuit, where theoutput of the CW circuit is connected to a 6.25 MΩ loadA. Breakdown of FeedbackWhen the power supply load falls within an allowablerange, the driving frequency is maintained higher than theresonance frequency such that the feedback is negative, asdesigned. However, although the allowable range of load issufficient for normal operation, it cannot cover, for example, ashort circuit (output voltage to ground). When the load deviatesFREQUENCY [Hz]70k 80k 90k 100kGAIN [dB]010203040PHASE [deg]-180-150-120-90-60-3003060working rangeinitializationFigure 3: Resonance shown by the transformer loaded with 100kΩfrom the allowable range, the driving frequency may decreasebelow the resonance frequency, resulting in positive feedbackand effectively locking the circuit such that it is independentof load. In order to restore the negative feedback control,the driving frequency must be reset externally in addition toremoving the load.1) Circuit ProtectionAn abnormal load outside the allowable range causesthe frequency of the VCO to decrease past the resonancefrequency. The positive feedback, accompanied with thebreakdown of feedback, reduces the frequency of the VCO toits lower limit. A frequency range of the VCO is adjusted sothat the output voltage could be lowered enough at the lowerlimit in frequency. Thus the breakdown of feedback reducesthe output voltage, providing circuit protection in the event offailures.B. VCOThe VCO is implemented by TLC555 and a flip-flop. Thedriving frequency is a function of the input voltage appliedto its input terminal. The input voltage is limited between2.3 V and 4.3 V. The driving frequency ranges from 80 kHzto 130 kHz. When the feedback breaks down, lowering thedriving frequency below the resonance frequency of thetransformer, the positive feedback raises the input voltage to anupper limit of 4.3 V, which reduces the driving frequency to80 kHz. While the negative feedback works as designed, theinput voltage remains relatively steady around 3 V, and doesnot exceed 4 V. Therefore feedback breakdown can be detectedas an increase in the input voltage beyond 4 V.C. Interface with Neuron ChipThe Neuron chip detects the breakdown of the feedback ata DSCRI terminal in Fig. 1. The VCO outputs the drivingfrequency as a square wave. Thus the Neuron chip counts thepulses at a FREQ1/2 terminal in Fig 1. The driving frequencycan be obtained by counting pulses over a fixed time interval.III. MEASUREMENTFig. 4 shows setup for measurement where the high voltagesupply module is interfaced by the Neuron chip. The module,making a LonWorks node, is controlled by a computer. Theoutput voltage is measured by a digital voltmeter connectedto the computer, where the probe of the voltmeter steps thevoltage down by a factor of 1000. Two voltage supplies provideelectricity to the module; 6.5-V feed provides a 5-V line , and avariable voltage source supplies the driver circuit and set by thecomputer for measurement.The node of the module includes a digital-to-analogconverter which generates the reference voltage. The computeris set up to send a signal to the digital-to-analog converterand measure the corresponding driving frequency. Thecorresponding output voltage across the load resistance atthe digital voltmeter is also monitored. In measurement, theoutput high voltage and the driving frequency are scannedautomatically by incrementing the value sent to the converter.The output voltage was then plotted against the converter valuerevealing that the output voltage is linearly proportional to theconverter value with negligible variance.6.5  V2.500 V3.0  VComputerVoltage supplyVoltage SupplyDigital voltmeterProbeFigure 4: Setup for measurementA. Output High Voltage against Driving FrequencyCorrespondence of the high voltage to the driving frequencymay depend on the load resistance and the supply voltageto the driver circuit. The high voltage is plotted against thedriving frequency for the various load resistances and thesupply voltages, and Fig. 5 shows the plots for a load resistanceof 21 MΩ with a supply voltage of 1 V to 3 V stepped inincrements of 0.5 V. The high voltage is limited below 3.5 kVbecause of isolation breakdown.It can seen from the plot that the high voltage remainsconstant between 130 kHz and 124 kHz. The high voltage cannot be lowered under the constant voltage. So the high voltageis clamped at the voltage while the high voltage is assigned tobe lower than the constant voltage.When the supply voltage is fixed, the high voltage becomesmaximum when the driving frequency is equal to the resonancefrequency of the transformer. Attempting to increase the voltagefurther results in feedback breakdown.For the transformer, the correspondence between theamplitude ratio and the driving frequency depends mainly onthe load. While the load is fixed, the correspondence may beinvariant to a first-order approximation. We therefore plottedthe high voltage divided by a conversion factor (voltage ratio)against the driving frequency, as shown in Fig. 6, where theconversion factor is estimated to be the product of the supplyvoltage, the multiplier at the CW circuit of 5.5, and the ratio ofamplitude of the carrier applied to the transformer to the supplyvoltage (3). Then, in rough approximation, the voltage ratio canbe compared with the amplitude ratio of the transformer. It canbe seen from the figure that the voltage ratio is linearly relatedto the supply voltage, which also holds for the amplitude ratio.02500300035005001000150020004000120 125 130Driving frequency (kHz)Output high voltage3.5 V3 V2.5 V2 V1.5 V1 VFigure 5: Output high voltage versus driving frequency for loadresistance of 21 MΩ with the supply voltages from 1 V to 3.5 V bystepped at 0.5 VB. Load ResistanceThe high voltage is plotted against the driving frequency forvarious loads, and Fig. 7 shows the plot for a load resistance of10 MΩ. Fig. 8 shows the plot for a load resistance of 4.7 MΩ.It can be seen from the figures that the resonance frequency ofthe transformer shifts lower frequencies as the load becomesheavier.IV. NETWORKA. Neuron ChipThe Neuron chip is a system-on-a-chip with multiplemicroprocessors, read-write and read-only memory (RAM andROM), a media-independent network communication port anda configurable I/O controller. The read-only memory contains020406080100120140120 125 130Driving frequency (kHz)Voltage ratioFigure 6: Voltage ratio plotted against driving frequency for a load of21 MΩ05001000150020002500300035004000120 125 130Driving frequency (kHz)Output high voltage3.5 V3 V2.5 V2 V1.5 V1 VFigure 7: Output high voltage is plotted against the driving frequencyfor a load of 10 MΩ and various supply voltages.an operating system, a LonTalk communication protocol, andan I/O function library. A complete implementation of theLonTalk protocol is contained in ROM in every Neuron chip.The chip has non-volatile RAM for configuration data and forthe application program, both of which are downloaded overthe network.The I/O controller provides two timer/counters andconfigurable 11 I/O pins. Each Neuron chip contains three8-bit CPUs. Two of the CPUs handle LonWorks protocolcommunication, and the third run an application. TheNeuron chip can communicates with other Neuron chips05001000150020002500300035004000120 125 130Driving frequency (kHz)Output high voltage3.5 V2.5 V2 V1.5 V1 V3 V4 VFigure 8: Output voltage versus driving frequency for a load of4.7 MΩ with various supply voltagesover a twisted-pair cable; a feature that allows establishing anetwork of the Neuron chip. The peer-to-peer protocol forcommunication allows all the Neuron chip connected to thenetwork to communicate with each other.B. Node for ModuleA LonWorks node for the high voltage power supplymodule includes the Neuron chip and integrates acommunication transceiver, a clock, reset circuitry, and a 12-bitdigital-to-analog converter. Most functions of the module beingbrought under the control of the Neuron chip, the modules aremonitored and controlled through the network. Fig. 9 showsthe interface with the module.Neuron ChipDAC7611LonWorksNetworkMAX707RESETRESETDATA ADATA BIO-7IO-8IO-9IO-6IO-5IO-4IO-3IO-2IO-1IO-0IO-10VCCGNDONOFFDISCRIFREQ1/2MR RSTPFIVCCGNDVREFCLRLDCLKSDIVOUTVDDGNDCSto power controlcircuitFigure 9: Interface circuit between chip and module1) Output High VoltageThe chip controls the 12-bit digital-to-analog converterwhich generates the reference voltage. The high voltage can becontrolled using the converter via the network. The referencevoltage ranges from 0 V to 4 V, and 1/1000 of the high voltage,divided by the divider resistor, is compared with the referencevoltage.2) Recovery from Feedback BreakdownThe Neuron chip detects the feedback breakdown andpropagates the report through the network, assisting resolutionof cause of the breakdown. The Neuron chip, followinginstructions received from the network, manages recoveryfrom breakdown, where firstly the reference voltage is reset,which initializes the driving frequency, and secondly the chipincreases the reference voltage to a prescribed value, restoringthe high voltage.3) Current MonitorIt is assumed that the supply voltage to the driver circuit isfixed. Once the high voltage is assigned, the driving frequencyat which the transformer is driven depends on the load. Thedriving frequency, obtained by counting pulses over a fixed timeinterval, allows the load to be calculated based on the shift of thedriving frequency.V. ACKNOWLEDGMENTSWe are indebted to the people engaged in development ofceramic transformer at Material Development Center, NECCorporation, for providing their newest ceramic transformers,and also indebted to Mr. Atsusi Ochi of NEC Corporation forcontinuous encouragement.VI. REFERENCES[1] Y. Shikaze, M. Imori, H. Fuke, H. Matsumoto, and T.Taniguchi, A High-Voltage Power Supply Operating undera Magnetic Field, IEEE Transactions on Nuclear Science,Volume: 48, June 2001 pp. 535 -540[2] M. Imori, T. Taniguchi, and H. Matsumoto, Performanceof a Photomultiplier High Voltage Power SupplyIncorporating a Piezoelectric Ceramic Transformer, IEEETransactions on Nuclear Science, Volume: 47, Dec. 2000pp. 2045 -2049[3] M. Imori, T. Taniguchi, and H. Matsumoto,A Photomultiplier High-Voltage Power SupplyIncorporating a Ceramic Transformer Driven byFrequency Modulation, IEEE Transactions on NuclearScience, Volume: 45, June 1998 pp. 777 -781[4] M. Imori, T. Taniguchi, H. Matsumoto, and T. Sakai, APhotomultiplier High Voltage Power Supply Incorporatinga Piezoelectric Ceramic Transformer IEEE Transactionson Nuclear Science, Volume: 43, June 1996 pp. 1427 -1431[5] S. Kawasima, O. Ohnishi, H. Hakamata et. al.,Third Order Longitudinal Mode Piezoelectric CeramicTransformer and Its Application to High-Voltage PowerInverter, IEEE Ultrasonic Sympo., Nov., 1994, Cannes,France. pp.525-530.[6] C. Y. Lin and F. C. Lee, Design of PiezoelectricTransformer Converters Using Single-ended Topologies,1994 VPEC Seminar Proceedings, pp.107-112.

High voltage power supply module operating in magnetic field

Abstract

Similar works

Full text

Available Versions

CERN Document Server