We have previously reported on improving the equipment by which an iron ball was made to float using a magnet, along with adjustment of the position of magnet and iron ball.  As a result, the time required to achieve floating was greatly reduced.  In this study we report on lightening the equipment and simplifying the operation.  Through trial and error we were able to float a ball of about 50 g gross mass.  And, it was possible through simple operations to make the iron ball float in a short time (few seconds).departmental bulletin pape

2077

2078

SAKURAI, Yuryo

サクライ, ユウリョウ

櫻井, 勇良

English

Shonan Institute of Technology Repository / 湘南工科大学学術リポジトリ

―  ―MEMOIRS OF SHONANINSTITIUTE OF TECHNOLOGYVol. 44, No. 1, 20091.	 IntroductionRecently, experimental results were reported in which an iron ball floated stably using simple equipment consisting of a plastic box, magnet and iron ball.1-3)  We saw and were impressed with the photograph of an iron ball floating in a magnetic field.  This phenomenon is very interesting as a physical phenomenon (i.e., Earnshaw's theorem).  If the iron ball floated completely free of physical contact, this is a significant discovery that violates Earnshaw's theorem which states that no fixed configuration magnet can be held stationary and stable by a three-dimensional (3D) static magnetic and /or gravitational forces without any physical contact.4)Using this phenomenon it may be possible to transport objects without physical contact.  This would be especially useful in semiconductor production processes which are extremely susceptible to contamination if there is physical contact with the object being moved.  Magnetic and gravitational forces are involved in this phenomenon, and the floating situation changes with changes in the balance conditions, i.e., control depends to a large extent on the position of iron ball and magnet.  Therefore, in order to carry out an effective study of this phenomenon it is necessary to continuously observe the delicate movement of the ball until it floats stably rather than observing only the floating condition.  Of course, the mechanism to control the position of the magnet and plastic box must be provided for in the experimental equipment.   It has been difficult to continuously observe the delicate movement to not only float the iron ball but also float it stably, because such a control mechanism was not available in the reported equipment. 1-3)In our previous paper, we developed the equipment to observe this delicate movement.5)  As a result of trial and error, we developed simple equipment that could drastically shorten the time required to make the iron ball float stably.  It was possible to continuously observe the delicate movement of the iron ball, and we were able to continuously observe the very small movement of the iron ball due to unbalances between the magnetic and gravitational forces.  Though the condition where the iron ball floated perfectly in a contactless condition could not be achieved, we were able to strongly suggest the possibility of perfect contactless floating.Many experiments were necessary to examine the various conditions necessary in order to get the equipment to produce contactless iron ball floating.  Therefore, it is desirable to make the operation of floating the iron ball as simple as possible.  The method (knack) of operating the equipment we developed for floating the ball is hard to express in language. Primarily, experience is necessary to make the iron ball float in the shortest possible time.  Based on this situation we specified certain requirements for the equipment to simply make the iron ball float. Requirements of the equipment are the following.*Department of Electrical and Electronic Engineering, Shonan Institute of Technology, 1-1-25 Tujido-Nishikaigan, Fujisawa, Kanagawa 251-8511, JapanSimplification of the Iron Ball Magnetic Levitation EquipmentYuryo SAKURAI* We have previously reported on improving the equipment by which an iron ball was made to float using a magnet, along with adjustment of the position of magnet and iron ball.  As a result, the time required to achieve floating was greatly reduced.  In this study we report on lightening the equipment and simplifying the operation.  Through trial and error we were able to float a ball of about 50 g gross mass.  And, it was possible through simple operations to make the iron ball float in a short time (few seconds).	 Key	words:	magnetic levitation, iron ball, Earnshaw's theorem, magnetization.湘南工科大学紀要　第44巻　第１号―  ―Simplification of the Iron Ball Magnetic Levitation Equipment （SAKURAI）―  ―(1) The equipment must be simple and light.(2) It must be simple to carry out the operation whereby the iron ball floats.(3) It must be possible to produce the float condition in a short time.(4) Since it is hard to recover from accidents involving the magnetic force, the magnet must be comparatively weak.2.	 ExperimentsThe equipment consists of a magnet and a container for storing the iron balls.  In this study we used small iron balls (diameter: 3.95 mm, mass: 0.279 g) in order to keep the equipment light.  A transparent pipe (outer diameter: 6 mm, inner diameter: 4 mm) was used as the container to store the iron balls.  Magnets of various shapes, sizes and materials, including a broken magnet were prepared.  These various magnets were combined sometimes in piles of two.  The experiment was carried out in the following manner.(1) The magnet or transparent pipe (including the iron ball) is held in the hand.(2) The transparent pipe is placed atop the magnet or combination of magnets.(3) Distance and positional relation between magnet and pipe are delicately adjusted in consideration of the instantaneous motion during descent and rise of the iron ball.The experimental result was synthetically evaluated, though the above-mentioned conditions were taken into consideration. The magnetic flux density distribution of the magnet was measured in order to fully define the magnetic field causing the floating. The sensor was fixed just under the magnet, and the magnet was made to move in 3D rectilinear direction.3.	 Results	and	DiscussionFig.	1  A photograph and schematic illustration of the experimental set up we developed for magnetic levitation of a single iron ball.Fig.	2  The condition of iron ball which floats in the plastic pipe: (a) preparation, (b) end face of the magnet, (c) center of the magnet, (d) z axis back.Figure 1 shows the experimental equipment.  As a result of trial and error, the ferrite ring magnet (magnetic flux density ~60 mT) of 45 mm outer diameter, 19.5 mm inner diameter 湘南工科大学紀要　第44巻　第１号―  ―Simplification of the Iron Ball Magnetic Levitation Equipment （SAKURAI）―  ―and 6.5 mm thickness was selected.  The ring type magnet was divided about in half, and the two pieces of the magnet were placed on top of each other (see Fig.1).  The upper end of the plastic pipe was fitted with a wooden plug so as to retain the iron ball.  A wooden rod the thickness of the inside of the plastic pipe was inserted in the pipe.  The distance between the iron ball and magnet was adjusted by relative motion of the wooden rod.  This wooden rod is grasped in the hand, and the plastic pipe is moved.  The gross weight of this plastic pipe, wooden plug and rod, and iron ball is about 46 g.  This is approximately 1/100 the gross mass of the (~4.5 kg) previous equipment.  Using this equipment and the above-mentioned procedure it was possible to float the iron ball within 10 seconds.  Further, the levitation phenomenon, including the instantaneous descent and climb motion, was also simple to reproduce.  The outline of the operation using this magnet is given in the following (see Figs.2 (a)-(d)).(1) The upper part of the plastic pipe is made to contact the magnetic inner diameter.(2) The plastic pipe is moved near the position of the two superimposed magnetic sheets, i.e., moved horizontally.(3) The transparent pipe is moved downward.This procedure was repeated, while the position of the wooden bar was adjusted.  As a result, one of the two iron balls floated but only when the plastic pipe was near the center of the magnetic and the superimposed magnetic sheets (see Fig.2 (c)).The broken magnet was used by accident.  There is no a special reason for using this magnet.  When using various magnets and broken magnets it was easy to float an iron ball when the ball was positioned “inside” the magnet.  We observed that over about 1/2 of the circular arc was necessary to float the iron ball.From these results we determined that it was possible to float the iron ball if the magnetic force was weak and the iron ball was placed inside the magnet diameter.  The magnetic flux density between the two superimposed sheets was about two times higher than outside the diameter.  This allowed the equipment to be made much lighter.  Because we were able to simplify and lighten the equipment, according to our goals, we achieved the contactless floating condition.Bx(mT)Fig.	3  Magnetic flux density distribution characteristic in the X direction, and in the region shown.湘南工科大学紀要　第44巻　第１号―  ―Simplification of the Iron Ball Magnetic Levitation Equipment （SAKURAI）―  ―Now consider the effect of the broken ring magnet.  Gravity and magnetic force affect the iron ball, and the levitation condition is determined by their balance.  The effect of the magnetic force is in certain areas greater than the gravity. Therefore the magnetic flux density distribution was measured over three-dimensions.Figures 3-5 show the magnetic flux density distribution in three-dimensions.  The magnetic flux density distribution in the X, Y direction was measured in the vicinity of the two stacked magnets.  In the Z direction the measurement was near the internal wall of the magnetic internal.  As shown in Fig.3, the magnetic flux density tended to decrease when moving away from the internal wall of the magnet.  Figure 4 shows the magnetic flux density to have a minimum near the center between the internal magnetic walls, i.e., a U-shape. As shown in Fig.5, the magnetic flux density distribution in the Z direction peaked in the vicinity of the boundary between the piled up magnetic sheets.Based on the success described above, the force on the iron ball was examined.  The plastic pipe with one iron ball was used.  The plastic pipe was moved in the region where magnetic flux density was measured, and the movement of the iron ball was observed.    The balance point existed a little below the actual levitation point in the X direction, i.e., the ball moved up when the iron ball was shifted up from the equilibrium position, and it fell, when the iron ball was shifted down from the equilibrium position.  In the Y direction, and though the iron ball was moved in the Y direction and near the internal magnetic wall, it did not react.  In the Z direction, and though the iron ball was moved in the vicinity of the boundary of the two magnet sheets above, it did not react.  A summary of the magnetic flux density distribution and force as described above is shown in Fig.6.Bx(mT)Fig.	4  Magnetic flux density distribution characteristic in the Y direction, and in the region shown.Bx(mT)Fig.	5  Magnetic flux density distribution characteristic in the Z direction at the designated magnetic inner diameter.湘南工科大学紀要　第44巻　第１号―  ―Simplification of the Iron Ball Magnetic Levitation Equipment （SAKURAI）―  ―Fig.	6  A schematic illustration of the magnetic flux density distribution of magnetic inner diameter: (a) x-axis direction, (b) y-axis direction, (c) z-axis direction, (d) three-dimensional direction.Fig.	7  The distribution of magnetic force and gravity.  The difference by have (a) nothing, and (b) the force pulling back to the balance point.Fig.	8  A schematic illustration of the three-dimensional force which affects the iron ball.Next, we examined the levitation motion of the iron ball. Magnetic force and gravity affect the iron ball used in this experiment.  Figures 7(a) and (b) show the outline of the balance of magnetic force and gravity force.  The iron ball floats at the balance of gravity and magnetic force.  In this delicate balance situation it is necessary to know the form of the force that restores the floating iron ball from any deviation so that it floats stably at the balance point, i.e., the existence of the force pulling the ball back for the balance point is important.  In the case of Fig.7(a), it is difficult for the iron ball to float stably because there is no force pulling the ball back to the balance point.   In simple terms it is necessary to realize the force distribution shown at Fig.7(b).  When the iron ball is under the influence of this force, the downward force acts on the iron ball to limit the top of the motion, and the upward force acts to limit the bottom of the motion, i.e., it is possible to stably float the ball because the force is always pulling it back toward the balance point.  Instantaneous descent and climb motion of the iron ball observed with this experimental equipment indicates the existence of a restoring force, i.e., this force must have the general characteristic of the force shown in Fig.7(b).  It is difficult to make the iron ball float only at the balance point.  The iron ball can also be slightly shifted from the balance point.   In the case of Fig.7(a), the iron ball can not deviate from the stable point position because the force pulling it back toward the balance point does not 湘南工科大学紀要　第44巻　第１号―  ―exist.  To achieve a stable float point it is necessary to have the distribution of force in which the restoring force on the iron ball shifted from the balance point acts to move the ball back to the stable point.  This means a force characteristic like that of Fig.7(b) is necessary.  However, the magnetic flux density distribution curve shown in Fig.7(b) is not the same as shown in Figs. 3-5.  A factor beyond the magnet must be considered for the magnetic flux density distribution of the force shown in Fig.7(b) to exist.  One of the factors is the magnetized iron ball, or more specifically the force generated between magnetized iron balls.  For the case of two iron balls the uppermost iron ball receives this repulsive force.  However, it can not move, because it is up against the upper part of the plastic pipe. The next lowest iron ball receives the force downward, and it separates from the uppermost iron ball.  This (lower) iron ball floats stably because of the balance of the upward force of the magnet and the repulsive force between the magnetized iron balls and gravity (see Fig.8).  These three forces, the magnet, the repulsion between the iron balls and gravity produce the force as shown in Fig.7(b).  The actual magnetic flux density distribution in this condition is unknown because of the influence of the magnetized iron ball.It is easy to understand that the magnetic flux density is complicated by the presence of the iron ball.  Therefore, the distribution of the force also is changed indicating the possibility of forming the distribution as shown in Fig.7(b). We surmised that the forces described do exist because of the motion before the ball floats.  In this study, the inference of the foregoing was obtained as a result of examining the levitation mechanism of the iron ball including this motion. Small upward and downward motion of the iron ball which occurs before it floats has been missed and examination of this motion was difficult.  The observation of this upward and downward motion, however, was easy to observe with the improved equipment that allowed control of the position of iron ball and magnet.The equipment in which the iron ball simply was made to float was produced.  And, the inference of the levitation mechanism was also observed.  However, whether the iron ball is in a contactless condition is uncertain.  It is necessary that the distribution of the force as shown in Fig.7(b) be formed in three dimensions so that the iron ball may float contactless.  It is now necessary to examine the Y and Z axis directions. The X-axis direction was confirmed by this study. This is a future problem.4.	 ConclusionBased on previous experimental results, lightening and simplification of the iron ball levitation equipment was performed.  The new equipment allowed floating of the iron ball of approximately 50 g with a few seconds.The following observations are the main reason why this equipment is simpler than the previous equipment and that the iron ball was made to float in a short time.(1) Since the iron ball was not placed at the outer diameter of the magnet, but at the inner diameter, the effect of part of the circular arc appeared.(2) A balance of gravity and magnetic force was easy to accomplish because of the lighter weight of the iron ball.References(1) S. Sasaki, I. Yagi, and M. Murakami, J. Appl. Phys. 95, 2090 (2004).(2) M. Murakami, Y. Nishimura, T. Hirooka, S. Sasaki, and I. Yagi, J. Appl. Phys. 95, 083911 (2005) .(3) M. Sakai, Y. Takabayashi, K. Sugawara, T. Shibayama, Y. Shimonura, T. Orikasa, K. Kamishima, and N. Hirastuka, J. Appl. Phys. 97, 083908 (2005).(4) S. Earnshaw, Trans. Cambridge Philos. Soc. 7, 97 (1842).(5) Y. Sakurai, J. Appl. Phys. 104, 044503 (2008).

Simplification of the Iron Ball Magnetic Levitation Equipment

https://shonan-it.repo.nii.ac.jp/record/2000258/files/21-26_%E6%AB%BB%E4%BA%95%E5%8B%87%E8%89%AF_Simplification%20of%20the%20Iron%20Ball%20Magnetic%20Levitation%20Equipment.pdf

Simplification of the Iron Ball Magnetic Levitation Equipment

Abstract

Similar works

Full text

Available Versions

Shonan Institute of Technology Repository / 湘南工科大学学術リポジトリ