Bergman, Richard D.

Western Dry Kiln Association

Western Dry Kiln Association. Meeting (55th : 2005 : Reno, Nev.)

Undetermined

ScholarsArchive@OSU

SMALL-SCALE LUMBER DRYING USING WOODGASIFICATION AS A HEAT SOURCERichard D. BergmanUSDA Forest ServiceMadison, WisconsinABSTRACTSmall, rural forested communities have the economic need to develop a wood productsindustry to replace the loss of large sawmills and maintain forest health. The mainobjective of this study was to explore the potential of using producer (wood) gas to fire ahot water boiler for a small dry kiln capable of drying both softwood and hardwood lumber.A BioMax wood gasifier, a hot water boiler, and dry kiln were integrated as parts of awhole lumber drying system for a field test in southwestern United States. Results so farfound the amount of gas heat produced from the wood chip-fed BioMax 15 and 50 is250,000 and 1,000,000 Btus per hour respectively, while the hot water boiler provides109,000 Btus per hour for a 3,500 board foot dry kiln.INTRODUCTIONThere are several million acres of forestland in the United States, particularly in the Westthat contains stand of pine so dense that forest health is affected and the risk ofcatastrophic forest fires is high. Removal of the small stems is expensive, and thereforeinterest in using this woody material is high. Also, as fossil fuel prices continue toincrease, alternative renewable fuels, like the gas produced from gasifying wood(producer gas), becomes more economical favorable.The harmful effect of high and rising oil prices on the economies and development effortsof oil-importing developing countries have become apparent. As a result, there has beenincreased interest in indigenous renewable energy sources, of which biomass in the formof wood or agricultural residues are the most readily available in many developingcountries. In many developing countries—particularly in rural areas—internal combustionengines are widely used in stationary applications such as electric power generation andoperation of water pumps and mills. Technologies such as wood gasification, which allowutilization of biomass fuel in such engines after minimum preparation, are therefore ofparticular importance.Designing and developing wood gasifiers as well as charcoal gasifiers have been aroundfor more than a hundred years. Wood gasification is the process of heating wood in anoxygen-limited chamber until volatile pyrolysis gases (i.e., carbon monoxide, hydrogen,and oxygen) are released from the wood. In the range of 395 *F to 535°F, the majority ofthe gases, which yield from 60% to 80% of the heat content of the wood, are driven off.This emitted wood gas, typically called producer gas, has energy content of 150 Btu percubic ft that is approximately 15% as strong as natural gas; still the producer gas canoperate an internal combustion engine. The major advantage wood gasification has overwood combustion is the substantial increase in efficiency. Extremely high combustionefficiency is obtained by gasification, thereby generating minimal emissions particularlyparticulate emissions.Western Dry Kiln Association 	 40	 May, 2005OBJECTIVESSmall, rural forested communities have the economic need to develop a wood productsindustry to replace the loss of large sawmills and maintain forest health. The mainobjective of this study is to explore the potential of using producer gas to gas fire a hotwater boiler providing heat for a small dry kiln capable of drying both softwood andhardwood lumber. Other objectives in this study include the following:Determine sizing of the (BioMax) wood gasifier required to run a dry kiln on a particularspeciesFind out if the dry kiln is capable of producing high quality kiln dried softwood andhardwood while using producer gas in a hot water boilerSoftwood lumber for constructionHardwood lumber for flooring• Determine potential part-time kiln drying• Determine potential kiln drying using heat from a storage tank overnightWood Gasifier — 250,000 BtltS per hourBACKGROUNDUsing renewable fuels like solid-wood fuel to provide heat for conventional steam kilns arequite typical and a common practice. On the other hand, very little work, if any, has beendone using producer gas to fire a boiler to heat a hot water kiln. In rural areas, fossil fuelprices continue to increase where wood residue has significant availability.One problem in connecting new, not quite commercially available technology (woodgasification) with standard technology like a hot water dry kiln is determining proper sizeof either unit. A proper-sized wood gasifier connected to proper-size dry kiln is alsodependent on the specie. Depending on specie, you can expect to kiln dry lumber from4 days up to 4 weeks.Western Dry Kiln Association	 41	 May, 2005Community Power Corporation (CPC) is adapting its BioMax 15 and BioMax 50 GasProduction Modules to provide thermal energy for drying lumber. In order to provide asystem that can meet the widest range of market requirements, we will be demonstratingthe ability to kiln dry both hardwoods and softwoods at the Zuni Sawmill in New Mexico.The kiln will have the flexibility to dry a range of woods to various quality standards asopposed to picking the easiest drying requirements and having a product with minimalmarket appeal.A packaged kiln capable of holding 3,500 board feet of 4/4 lumber will be obtained andtested at a facility selected by CPC, and then put in the field at Zuni, New Mexico, for a1-year test.A method must be developed to transfer thermal energy in a controlled manner from acombusted flame to the packaged kiln. Proper kiln drying to produce high quality lumberis another issue that will be addressed in this study because of the uncertainty of whetherthe kiln can function part-time. Also, the potential of utilizing heat from an insulated watertank when the wood gasifier is shutdown will be determined.If the BioMax 15 is oversized for a 3,500 board foot kiln, the options exist to operatemultiple kilns, find other on-site uses for the excess energy, flare the excess energy, storethe energy, or cycle the system.While testing, we will dry both hardwoods and softwoods to confirm the viability of thesystem. We will also dry softwoods and hardwoods in the field in New Mexico.It is believed that the current design of the BioMax 15 can provide 250,000 Btu/hour forat least 8 to 10 hours per day and that the current design of the BioMax 50 can provide1,000,000 Btu/hour for at least 16-24 hours per day.Three different sizes of the BioMax have been or soon will be operating in the field witha variety of functions, including providing heat and power for a research house, traditionalhousing (Hogans), greenhouses, and small businesses, particularly wood productsindustry.The BioMax 15 was the first of the three models to be field-tested with a unit running oncoconut shells installed to provide electricity for a Philippine village in the 1990s. Due tothe forest fires of 2000, an emphasis was given to manage our National Forests to preventthe catastrophic forest fires that still continue to occur to this day through mechanicalthinning. A good use of.this thinning material is wood for energy although it is not as goodas a revenue generator as are saw logs. It does utilize material that would otherwise beleft in the woods as a potential fire hazard. Through a partnership of the USDA ForestService State & Private Forestry Technology Marketing Unit (S&PF TMU) located at FPL,the National Renewable Energy Laboratory (NREL), and CPC, we are field-testing threeBioMax 15s and one BioMax 50.As a continuation of utilizing this wood gasification technology, we are providing technicalassistance to CPC as the company works on integrating their technology with standardcommercial dry kiln technology. Presently, the boiler is being tested at CPC using theproducer gas from the BioMax. The second step is integrating the hot water boiler dry kiln.Western Dry Kiln Association	 42	 May, 2005r.DHot Water Dry Kiln04.)-0 0-0 0•	 Gas lowLEW:a0PROCEDURESMaterial• BioMax 15 / 50 – wood gasification production module• Gas-fired hot water boiler (109,000 Btus per hour)• –3,500 board foot hot water dry kiln• (1) Load of Ponderosa Pine / (1) Load of poplarExperimental DesignThe study will follow the design and development of an integrated system capable ofcombusting producer gas from a BioMax in a gas-fired hot water boiler, using the thermalenergy to dry both softwood and hardwood lumbers on a small-scale.• Test the boiler with producer (wood) gas from the BioMax at CPC to ensure properoperation of boiler prior to field-testing.• Assemble the dry kiln prior to transportation to the Zuni Sawmill in Zuni, NM (by dry kilnmanufacturer).• Install the whole system on site and test with a load of softwood and hardwood tocompare drying times plus lumber quality.Data collection will include the following during kiln operation:• Wood consumption (pounds per hour)• Moisture content of wood fuel (% MC)• Producer gas flowrate (ft 3 per hour)• Estimated energy content of producer gas (BTU per ft3)Wood Clips IFeeder/Dryer Module• Hot water flowrate (ft 3 per hour)• Hot water supply temperature (°F)Nur TO SCATFigure 1. Block diagram of BioMax 15 integrated to hot water dry kiln.Western Dry Kiln Association	 43	 May, 2005• Hot water return temperature (°F)• Volume of hardwood lumber (thousand board feet)• Volume of softwood lumber (thousand board feet)• Initial %MC / Final %MC for both softwood and hardwood• Kiln Temperature (°F) / Relative Humidity (%MC)• Moisture loss per day (%MC) – kiln samples / moisture sectionsKiln DryingPonderosa Pine Schedule (Approximate): 3-4 days at 140°F: Green to 19% MCYellow Poplar Schedule (Approximate): 5-6 days at 140°F: Green to 6% MCANALYSIS(1) For a 5,000 board foot kiln that is using the thermal energy from a BioMax 15 (up to250,000 Btu/hr), how much energy (hourly, daily, total) is needed to dry softwoods andhardwoods to market requirements given that the system must have the capability to drywood in both summer and winter environments. If there is a quality difference in the typeof wood being dried (furniture vs. structural applications, for example), how will this impactthe energy needed?(2) What are the desired temperature profiles for drying hardwoods and softwoods ofdifferent quality types? If the user cannot provide the labor to operate the system 24 hoursper day and does not want to leave the system unattended during operation, is it possibleto operate the kiln in shifts of 8 to 10 hours per day, 5 days per week? What are thedisadvantages of the thermal cycling that this drying strategy would entail?(3) Is there a value to energy storage? How would we store the energy? How would werelease it in a controlled manner?(4) What are the different heat transfer options? What are the advantages anddisadvantages for each? Which is the preferred option for CPC?(5) What is the preferred design of a packaged dry kiln that has been integrated with asmall modular biopower system? Provide a schematic of the integrated system.(6) Is the 250,000 Btu/hr system oversized? How can we best use the excess energy ifthis is the case?(7) What are the fundamental design decisions that we need to make as we go along inthe program?(8) What are the details of lumber drying tests to be conducted at CPC including, but notlimited to, such considerations as types of wood, quality types, sources of supply,estimated cost (including transportation), moisture content, kiln loading, temperatureprofile, measurements needed, etc?Western Dry Kiln Association	 44	 May, 2005TIME SCHEDULESeptember 2004January 2005May 2005August 2005November 2005BUDGETInitiate development of gasifierResearch kiln designObtain hot water boilerObtain dry kiln / integrating with boilerField Test BioMax and dry kilnCommunity Power Corporation will cover all costs for the project. Funding of $750,000came from the Small Business Innovation Research (SBIR) Program.TECHNOLOGY TRANSFEROne publication is expected that describes how well the integration of the BioMax to a hotwater dry kiln performed for both softwoods and hardwoods and proper sizing of theBioMax to the hot water dry kiln.LITERATURE CITEDShottafer, J.E. and Shuler, C.E. 1974. Estimating Heat Consumption in Kiln DryingChamber. Life Science and Agricultural Experiment Station Technical Bulletin 73.University of Maine at Orono.Simpson, W.T. and Tschernitz, J.L. 1978. Time, Costs, and Energy Consumption forDrying Red Oak Lumber as Affected by Thickness and Thickness Variation. ForestProducts Journal 30(1): 23-28. Forest Products SocietySkaar, C. 1977. Energy Requirements for Drying Lumber. Practical Application of SolarEnergy to Wood Processing Workshop Proceedings pg. 29-32.Calabrese, D. 2004. Father, Son Launch Hardwood Drying Operation. TimberlineCalabrese, D. 2003. Kentucky Family Mill Expands into Drying. TimberlineCalabrese, D. 2002. Dansville Companies Complement Each Other. Timberline... 2000. Constant Venting is Heart of Koetter Technology. Timberline.Petree, J. 2001. McCready Finding Success in Treated Lumber. Timberline........ 2004. Biomass for Small-Scale Heat and Power Techline. Forest ProductsLaboratory State & Private Forestry Technology Marketing Unithttp://www.fpl.fs.fed.us/documnts/techline/biomass for small-scale heat and power.pdfWestern Dry Kiln Association	 45	 May, 2005Zuni SawmillZuni Solar Dry Kilns-PresentHot Water Dry Kiln-FutureWestern Dry Kiln Association	46	May, 2005

Small-scale lumber drying using wood gasification as a heat source

https://ir.library.oregonstate.edu/downloads/m613mz48m

Small-scale lumber drying using wood gasification as a heat source

Abstract

Similar works

Full text

Available Versions

ScholarsArchive@OSU